Myson Kickspace 500E Bedienungs- und Wartungshandbuch
KICKSPACE 500 E
ELECTRIC FAN CONVECTOR
1370041 - 04
INSTALLATION, MAINTENANCE AND
OPERATING INSTRUCTIONS
AND TECHNICAL DATA
PLEASE READ THESE INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION
AFTER INSTALLATION LEAVE THESE INSTRUCTIONS WITH THE USER
B.E.A.B.
Approved
®
2
Fig. 3.2 - Plinth opening
PREPARATION - continued
3.1 A clean and level floor area is required under the cupboard base.
3.2 Decide the position of the Kickspace, mark out and cut the plinth to the dimensions given in Fig. 3.2.
A minimum 25 mm clearance is required above the finished floor level.
3.3 A suitable support must be securely fitted to the floor. The top of the support must be level with the lower
edge of the cut-out when fitted.
A minimum of 25 mm clear headroom is required above the top of the Kickspace when fitted.
3. PREPARATION
2. ELECTRICAL SUPPLY
WARNING:THIS APPLIANCE MUST BE EARTHED.
The electrical installation must comply with IEE
Wiring Regulations (UK) or local regulations in
other countries.
2.1 The Kickspace is supplied fitted with a 2 metre
1.0 mm² cord.
2.2 A fused (10A) electrical spur with a switch
having 3 mm separation in all poles must be
provided in an easily accessible position
adjacent to the Kickspace, as shown in Fig. 2.2.
2.3 Room Thermostat - A room thermostat may
be fitted to give local temperature control. This
should be wired to the fused spur. See wiring
diagram in section 7.
Do not energize the electrical supply until the remaining
stages of the installation have been completed.
ELECTRICAL SUPPLY - continued
Switched fused spur
Kickspace
Fig. 2.2 - Electrical supply
1. APPLICATION
The Kickspace 500 E is intended for installation in the cavity beneath kitchen cupboards on the vacant floor space. In
this position, consideration should be given to the storage of perishable goods in the cupboard above.
THE KICKSPACE 500 E MUST NOT BE LOCATED IMMEDIATELY BELOW A SOCKET OUTLET.
THE UNIT MUST NOT BE INSTALLED IN A BATHROOM OR A ROOM CONTAINING A SHOWER.
No rear access shall be available to the unit after completion of installation.
3
5.1 With the electricity supply disconnected,
remove the two screws holding the safety cover
and discard the cover.
5.2 Align the grille and secure it to the unit using
the two screws previously removed.
5. COMPLETION COMPLETION - continued
5.3 Secure the unit/grille to the plinth with two
screws supplied.
Fig. 5.3 - Secure the unit to the plinth
Fig. 5.2 - Fit the grille
5.4 Complete the electrical supply, switch on and
test the Kickspace.
Front view of unit
Grille securing screws
Front view of unit
Unit securing screws
4.1 Position the Kickspace under the cupboard in the
required location, with the front edge just behind
the line of the plinth.
Note: Ensure that the electrical cord is not in contact
with any hot surface.
4. FITTING THE KICKSPACE
4.2 Replace the plinth and bring the Kickspace forward
into the opening so that the front edge projects 8
mm through the plinth.
FITTING THE KICKSPACE - continued
Fig. 4.2 - Ensure 8 mm projection
Fig. 4.1 - Position the Kickspace
6. CONTROLS 7. WIRING DIAGRAM
Fig. 6 - Controls
Heating switch
(Blue Off Red)
Fan speed switch
(Boost Low)
Power selector switch
(2 kW or 1 kW)
8 mm projection
Top view of unit
Colour code: br-Brown, bl-Blue, r-Red, p-Purple,
y-Yellow, g/y-Green/Yellow
8. Operation
Ensure that the electrical supply is switched on.
8.1. Heating
Set the Heating switch to the red disc position position, see Fig. 6.
Set the Power switch to either 2 kW or 1 kW as required, see Fig. 6. The fan will operate at the appropriate speed for
the element selected. The Fan Speed switch does not operate in these conditions.
DO NOT COVER THE UNIT OR OBSTRUCT THE GRILLE AREA. IF COVERED THERE IS A RISK OF FIRE.
8.2. Temperature control
If a room thermostat is connected to control the Kickspace, its setting should be gradually adjusted to obtain the required
temperature. Use the Power switch at 2 kW (II) or 1 kW (I) as required, see Fig. 6, to increase or decrease the heat output of
the unit.
8.3. Air circulation
If required, the Kickspace can be used in Summer for air circulation without heat.
Set the Heating switch to the blue disc position, (if a remote room thermostat is fitted, set it to its highest setting).
Set the Fan Speed switch to either Boost ( ) or Low position ( ), see Fig. 6, to select the required speed.
9. MAINTENANCE
Isolate the electrical supply.
Maintenance should be restricted to occasional removal of dust and lint around the unit. Any further maintenance should be
carried out by a qualified engineer.
In case of further service requirements, contact your supplier.
10. TECHNICAL DATA
Heat output: 2 kW at Boost speed (II)
1 kW at Low speed (I)
Electrical supply: 230 - 240 V ~ 50 Hz 2025 W
MYSON RADIATORS LTD, REGISTERED IN ENGLAND NO. 653648.
REGISTERED OFFICE: EASTERN AVE., TEAM VALLEY TRADING ESTATE, GATESHEAD, NE11 0PG
All descriptions and illustrations contained in this leaflet have been carefully prepared but we reserve the right to make changes and improvements in our
products which may affect the accuracy of the information contained in this leaflet. The statutory rights of the consumer are not affected.
© Myson Radiators Limited 2001. All rights reserved. No part of this leaflet may be reproduced by any means without prior written consent.
Manual compiled and designed by Publications 2000 (01670) 356211 10/01/D74
Andere Handbücher für Kickspace 500E
1
Inhaltsverzeichnis
Andere Myson Heizung Handbücher
Myson
Myson DÉCOR KH11 Bedienungsanleitung
Myson
Myson LO-LINE RC 6-4 Bedienungsanleitung
Myson
Myson 6-4 Bedienungsanleitung
Myson
Myson Rio Bedienungsanleitung
Myson
Myson HI-LINE RC 7-4 Bedienungsanleitung
Myson
Myson 6-4 Bedienungsanleitung
Myson
Myson 7-4 Bedienungsanleitung
Myson
Myson ELECTRIC DECOR H EXX20060 Series Wartungs- und Serviceanleitung
Myson
Myson SELECT Kurzanleitung
Myson
Myson HEK Bedienungsanleitung
Myson
Myson KICKSPACE 500 DUO Montageanleitung
Myson
Myson WHISPA III 9000 WM Bedienungsanleitung
Myson
Myson 40G Bedienungsanleitung
Myson
Myson iVector S2 Bedienungsanleitung
Myson
Myson FINESSE SC. Bedienungsanleitung
Myson
Myson ULOW-E2 Kurzanleitung
Myson
Myson iV080 Bedienungsanleitung
Myson
Myson SLIM-LINE RC Bedienungsanleitung
Myson
Myson Kickspace 500E ECO Montageanleitung
Myson
Myson T6 Series Bedienungsanleitung
Beliebte Heizung Handbücher anderer Marken
Empire Heating Systems
Empire Heating Systems WCC65 Bedienungsanleitung
Wetekom
Wetekom 92 86 43 Bedienungsanleitung
Desa
Desa SPC170-F Bedienungsanleitung
Watlow
Watlow Watrod Electric Tubular Heaters Bedienungsanleitung
Haverland
Haverland ECO-DRY GPS Series Stücklistenhandbuch
Stelpro
Stelpro ASILVC2060 Series Bedienungsanleitung