Myson Touch RS Bedienungsanleitung
Operating Instructions
Myson Touch RS
10/12 Revision 1
Ref: Myson Touch RS
11
Contents Page
Display Symbols Explained 7
Temperature Display 8
Setting the Clock 8
Comfort Levels Explained 9-11
Locking the Keypad 12
Temperature Override 12
Temperature Hold 13
Holiday 13-14
Heat On/Off 14
Clean Screen 15
Factory Reset 15
Optional Feature Setup 16-21
Re-calibrating the Thermostat 22
Wiring Diagrams 23-24
2
What is a programmable room thermostat?
A programmable room thermostat is both a programmer
and a room thermostat. A programmer allows you to set
“On” and “Off” time periods to suit your own lifestyle. A
room thermostat works by sensing the air temperature,
switching on the heating when the air temperature falls
below the thermostat setting, and switching it off once this
set temperature has been reached.
So, a programmable room thermostat lets you choose when
you want the heating to be on, and what temperature it
should reach while it is on. It will allow you to select different
temperatures in your home at different times of the day (and
days of the week) to meet your particular needs.
Turning a programmable room thermostat to a higher setting
will not make the room heat up any faster. How quickly the
room heats up will depend on the design of the heating
system, for example, the size of the boiler and radiators.
3
Any setting selected will not affect how quickly the room
cools down. Turning a programmable room thermostat to
a lower setting will result in the room being controlled at a
lower temperature, and will save energy.
The way to set and use your programmable room thermostat
is to find the lowest temperature setting that you are
comfortable with, and at the different times you have chosen.
Then leave it alone to do its job.
The best way to do this is to set a low temperature first,
say 18°C, and then increase the setting by one degree
each day until you are comfortable with the temperature.
You should not have to adjust the thermostat further. Any
adjustment above these settings may waste energy and cost
you more money.
If your heating system is a boiler with radiators, there is
usually only one programmable room thermostat to control
the whole house. But you can have a different temperature in
an individual room by installing thermostatic radiator valves
(TRVs) on each radiator. If you do not have TRVs, you should
choose a temperature that is reasonable for the
4
whole house. If you do have TRVs, you can choose a slightly
higher setting to make sure that even the coldest room is
comfortable. In the other rooms adjust the TRVs to prevent
any overheating.
The time on the programmer must be correct. The clock will
have to be adjusted in spring and autumn at the changes
between Greenwich Mean Time and British Summer Time.
Programmable room thermostats need a free flow of air
to sense the temperature, so they must not be covered
by curtains or blocked by furniture. Programmable Room
Thermostats must be sited to avoid localised heat from
sunshine, electric fires, televisions, and wall or table lamps
that may prevent the thermostat from working properly.
5
Installation Procedure
DO’s
1. Do mount the thermostat at eye level.
2. Do read the instructions fully so that you get the best from
our product.
DON’Ts
1. Do not install near a direct heat source as this will affect
the workings of the thermostat.
2. Do not push hard on the LCD (liquid crystal display).
The LCD will be damaged and this is not repairable.
6
Installation
The thermostat is designed to be flush mounted; a back box
of 25mm should be sunk in the wall prior to installation.
Step 1
Carefully separate the front half of the thermostat from the
back plate by placing a small flat head terminal screwdriver in
to the slots on the bottom face of the thermostat.
Step 2
Place the thermostat front half somewhere safe.
Terminate the thermostat power supply as shown in the
diagrams at the back of this booklet.
Screw the thermostat back plate on to the back box.
Step 3
Clip the thermostat front half to the back plate.
7
Display Symbols Explained
Symbol Description
Heat On Icon
Shown when the heating is On
Flashing when the Smart Start is in operation.
Frost On Icon (Heating Off)
Shown when the heating is switched off and is
protected against frost only
Keylock Icon
Shown when the keypad is locked
OFF Icon
OFF The OFF button is always displayed,
press once will toggle on/off Frost Protection.
Press and hold OFF to turn the display off.
8
Temperature Display
Room Temp = This is the current room temperature.
Floor Temp = This is the current floor temperature.
SET = This is the temperature you are trying to achieve in
your home.
Setting The Clock
To set the clock in your thermostat, follow the steps below:
• Withthethermostatturnedon,pressPROG.
• PressCLOCK.
• Use to set the correct Time.
• PressDAYtosetthecorrectDay.
• PressDONEtoacceptandstore.
Inhaltsverzeichnis
Andere Myson Thermostat Handbücher
Myson
Myson MPRT RF Bedienungsanleitung
Myson
Myson 63050507401 Bedienungsanleitung
Myson
Myson MPRT Bedienungsanleitung
Myson
Myson TOUCH4 Bedienungsanleitung
Myson
Myson Touch 2 WiFi Bedienungsanleitung
Myson
Myson Unisenza Plus Thermostat Bedienungsanleitung
Myson
Myson MPRT RF Bedienungsanleitung
Myson
Myson MRT1 Bedienungsanleitung
Myson
Myson MPRT MS Bedienungsanleitung
Myson
Myson REMOTE ROOM THERMOSTAT CONTROL Bedienungsanleitung
Beliebte Thermostat Handbücher anderer Marken
EWELLY
EWELLY EW-181 Bedienungsanleitung
Prolon
Prolon T1100 Montageanleitung
Computherm
Computherm Q20 Bedienungsanleitung
Heatmiser
Heatmiser neoStat Bedienungsanleitung
Aube Technologies
Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung
Mars
Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung
