Nady Systems ENCORE DUET Bedienungsanleitung

Dual Receiver VHF Wireless Microphone System

CONTENTS ....................................................................................................2

INTRODUCTION .............................................................................................2

USING THIS MANUAL .....................................................................................2

SYSTEM FEATURES ..........................................................................................3

ENCORE DUET RECEIVER.................................................................................4

WHT HANDHELD MICROPHONE TRANSMITTER ................................................7

WLT LAVALIER/LAPEL OR HEADWORN MICROPHONE

BODYPACK TRANSMITTER................................................................................9

WGT INSTRUMENT BODYPACK TRANSMITTER ................................................11

SPECIFICATIONS...........................................................................................13

SERVICE INFORMATION ................................................................................14

WARRANTY ..................................................................................................15

CONTENTS

Thank you for choosing the Nady Encore DUET dual receiver wireless microphone

system, we know you will be very pleased with its performance and features.

The Encore DUET is loaded with top professional operating features and is the

best performance and price value available in VHF dual receiver wireless systems.

This booklet provides information regarding the use of the Encore DUET VHF wireless

system and includes a description of features and a step‑by‑step guide to operation of

the unit. This manual should answer any questions you may have about the operation

and servicing of your Encore DUET.

INTRODUCTION

USING THIS MANUAL

•Dualchannelsystemforsimultaneousoperationoftwotransmitters

•AvailableontwoselectedfrequenciesintheVHFhighband(171-216MHz)

for interference‑free, long‑range performance

•Proprietarycompandingcircuitryforanindustry-best120dBDynamicRange,

and the clearest, most natural sound available

•OperatingRange:Upto250feettypical(dependingonsiteconditions)—

upto500+feetline-of-sight

•Noise-freetransmitterON/OFFoperation

• Rugged,foam-paddedtravelingcaseprovideseasy,safetransportandstorage

ENCORE DUET RECEIVER

•Half-rackdualreceiverdesign(ChannelAandChannelB)withretractable

front panel dual antennas

•DualRFandAF5-LEDdisplaysformonitoringincomingsignalstrength

and audio level on both channels

•DualbalancedXLRandunbalancedadjustable1/4"jackoutputs

•Dualmute(squelch)adjustcontrols

•ExternallypoweredbyAC/DCpoweradapter

•Uniquesnap-outpanellockingtabsforsinglereceiverordoublereceiver

(side-by-side)optionalrackmounting

WHT HANDHELD MIC TRANSMITTER

•FeaturestheNadyDM-10Dunidirectionalneodymiumdynamiccartridgefor

optimumtruesound,maximumfeedbackrejectionandminimalhandlingnoise

•OFF/STANDBY/ONswitchallowsconvenientaudiomutingwiththe

 transmitter"ON"

•LowbatteryLEDindicatorashesonceforunit"ON";lightssteadyfor

low battery alert

WGT & WLT BODYPACK TRANSMITTERS

•Choiceofinstrument(WGT)orheadworn/lavaliermicrophone(WLT) 

bodypack transmitter

•OFF/STANDBY/ONswitchallowsconvenientaudiomutingwiththe

 transmitter"ON"

•LowbatteryLEDindicatorashesonceforunit"ON";lightssteadyfor

low battery alert

•Locking3.5mmmini-jackprovidessecureconnectionforremovable

microphone or instrument cable

•Easilyaccessibleinputleveladjustcontrolforoptimumsound

SYSTEM FEATURES

1. Rackmounting the Receiver

TherearetwooptionsavailableforrackmountingtheEncoreDUETreceiver:

singly or side‑by‑side with another Encore Series receiver.

a. Single mounting: Remove the receiver SIDE MOUNT CLIP (1) from each side of

thereceiver(asshown)andslideintheoptionalERM-12 RACK EARS (9).

b. Side-by-side double mounting: After removing the SIDE MOUNT CLIPS (1) from

bothEncorereceivers,jointhetworeceiverswiththeEJC-2 JOINING CLIP (10)

and attach the ERM-22 RACK EARS (12) as shown.

(Note: Do not mount the receiver in a rack directly above an ampliﬁer or

other source of high heat — this could degrade the performance of the

Encore DUET. Always ensure adequate airﬂow and heat dissipation in

any rack conﬁguration.)

2. Powering the Receiver

Plug the 12V AC/DC ADAPTER (15) provided into the DC INPUT JACK (11) on the

back of the receiver. Then plug the power supply into an AC outlet.

(Note: Any 12V DC source with 400mA capability can also be used.)

Press the POWER SWITCH (8) once to turn on the receiver. The POWER ON LED (7)

will now light and the receiver is operational.

3. Antennas

The Encore DUET receiver is supplied with TELESCOPIC ANTENNAS (16), one each

forChannelAandChannelB.Theseshouldbeextendedfullytoobtainmaximum

range.Optimalantennapositionis45degreesfromthereceiver(at90degrees

fromeachother).Formaximumrange,itisalwaysbesttomaintainalineofsight

(noobstructions)betweenthereceiverantennasandthetransmitteratalltimes

whenever possible.

4. Mute (Squelch) Adjustment

In normal operation, the MUTE CONTROLS (2) foreachchannel(A&B)shouldbeset

fully counterclockwise to the factory preset minimum RF level. However, in areas of

highRFactivity,themutes(orsquelches,astheyaresometimescalled)mayneedto

beadjustedtocompensatefortheadverseconditionsinaparticularlocation.If,with

the transmitter off, one or more LEDs of the receiver's 5 LED RF LEVEL DISPLAYS (4) for

thatchanneltransmitterickerorstayon,thesquelchcontrolforthatchannelshould

beturnedclockwiseuntiltheLEDsextinguish.Whenthesquelchisproperlyadjusted,

the RF LEVEL LED displays will only light when that channel transmitter is turned

on. Turning the squelch control too far clockwise will reduce the range, but yield a

quietermute(squelch)function.Whenthe5 LED RF LEVELdisplayextinguishes,the

transmitter for that channel is out of range for that given location, and the user should

move closer to the receiver to re‑establish the radio link.

ENCORE DUET RECEIVER

5. Connecting the Audio Output

TheEncoreDUETreceiverprovidesbothaxedmiclevelBALANCED AUDIO OUTPUT

XLR (14)foreachchannelandanadjustablelinelevelA + B UNBALANCED AUDIO

OUTPUT 1/4" JACK (13) whichprovidesamixed(summed)ChAplusChBoutput

signal.ThemixedlevelfromtheA + B UNBALANCED OUTPUT is controlled by the rear

panel VOLUME CONTROLS (6) for each channel.

(Note: As when making any connection, make sure the ampliﬁer or mixing board

volume is at the minimum level before plugging in the receiver to avoid possible

sound system damage. Also make sure that the phantom power on the input of the

mixer is turned OFF before making connection to the receiver.)

a. Instrument Connection(usingtheWGTinstrumenttransmitter)

 Insertanaudiocordwitha1/4"monophoneplugintheA + B

UNBALANCED OUTPUT JACK (13) on the rear panel of the receiver. Plug the

otherendofthecordintoanamplier,effects,ormixingboard.Adjustthe

appropriate VOLUME CONTROL (6) for the channel being used on the Encore

DUETreceiverclockwisetoabout3/4rotation,untilthemixedvolumelevelis

comfortable for your application. This setting is roughly equivalent to a direct

instrumentcordconnection.Turningthevolumeuptomaximumwillprovide

4dB gain over a cord. (Note: Since this a mixed output of Ch A & Ch B, both

channels with be processed simultaneously by the ampliﬁer and/or effects

connected to, which may not be appropriate for your application.

b. Microphone Connection(usingtheWLTtransmitterwitheitheraheadset

orlavaliermicrophoneortheWHThandheldmicrophonetransmitter)

For microphone use, either the BALANCED MIC AUDIO OUTPUT XLRs (14) or the

1/4" line level A + B UNBALANCED OUTPUT (13)canbeused.TheXLRoutput

issetatanon-adjustablemicrophonelevel,similartohardwiredmiclevels.

PluganXLRconnectorintoeitherorbothoftheXLR OUTPUT JACKS on the

rearoftheunitandplugtheotherendintoyouramplierormixingboard.

(Note: Make sure the phantom power on your mixing board is turned off

and the volume is turned down when making connections.)

Foryourconvenience,theXLRoutputlevelsarepresetatthefactoryand

arenotadjustablewiththereceivervolumecontrols.Tousethe1/4" A + B

UNBALANCED OUTPUT JACK (13), follow the instructions for the Instrument

Connection(above),exceptstartwiththereceivervolumeat1/2MAX

andadjustthevolumecontrolforeachchanneluntilthemixedChAand

Ch B volume level is optimal. If the volume controls are set too high, you

mayoverloadyourmixeroramp.

4 45 5

14 14 2 156 13 11 6

1. Unscrew the BATTERY COMPARTMENT COVER (17)andremove,exposingthe

BATTERY HOLDER (18). Insert a fresh 9V ALKALINE BATTERY (19), observing the

correct polarity as marked, and screw the cover back on to the microphone.

Make sure the cover is screwed on completely. A fresh alkaline battery can

lastupto16hoursinuse,butinordertoensureoptimumperformance,itis

recommendedthatyoureplacethebatteryafterevery10hoursofuse.

2. Turn on the WHT by sliding the OFF/STANDBY/ON SWITCH (20) to the STANDBY

position(transmitteron,audiomuted)ortheONposition(transmitterandaudio

bothon).TheBATTERY INDICATOR LED (21)willgiveasinglequickash,indicating

usable battery strength. In the case of a dead or low battery, the LED will either

not go on at all or will stay on continuously, indicating that the battery should be

replaced with a fresh one. To preserve battery life, turn the transmitter off when

not in use.

3. The microphone is now ready to use. Most or all of the RF LEVEL DISPLAY LEDs (4)

on the Encore DUET receiver should now be lit, indicating a received signal

from the transmitter. When ready to speak, slide the transmitter switch to the ON

position.AdjustthevolumeofthereceiveraspertheAudioOutputMicrophone

Connection section of the above Encore DUET receiver instructions. The AF LEVEL

LED DISPLAY (5)ontheEncoreDUETreceiverwilllightupto5LEDs(4greenand

1red)forallinputsignals.Occasionalickeringonandoffduringuseofthe

top red LED indicator in this display is normal, however if the red LED stays on

continuously, it means the signal is too loud and there is the possibility of overload

distortion.BackofffromthemicrophoneuntiltheredLEDindicatoronlyickers

on peaks.

[Note: Observe care in selecting P.A. volume, transmitter location and speaker

placement so that acoustic feedback (howling or screeching) will be avoided.]

[Note: Microphone elements can easily be destroyed by the buildup of salts and

minerals from perspiration and saliva. It is good practice to put a windscreen on

the mic element at all times to protect it.]

WHT HANDHELD MICROPHONE TRANSMITTER

1. Snap open the BATTERY COMPARTMENT (22) and insert a fresh 9V BATTERY (23),

observing the correct polarity. Close the compartment.

2. The WLT is provided with a 3.5 mm LOCKING JACK (24) for connecting the

microphone. Plug in either the LAVALIER/LAPEL (25) or the HEADWORN

MICROPHONE (26), as supplied. To secure the connection, turn the metal slip ring

ontheplugclockwisetothreaditontothejack.Tounplug,reversetheprocess.

Slip the transmitter into a pocket or clip on to your clothes. To use the lavalier mic,

attachitatchestlevel.Donotplacetooclosetothemouth—adistanceofabout

sixinchesusuallyworksbest.Tousetheheadwornmic,placeitontheheadand

adjustthemicboomsothatthemicisaboutoneinchtothesideofthefrontof

the mouth. (Note: The lavalier or headworn mic wire is also the transmit antenna,

and rolling up or shortening the wire may reduce the effective operating range.

Extend the wire fully during use, and keep it as straight as possible.)

3. Turn on the WLT by sliding the OFF/STANDBY/ON SWITCH (27) to the STANDBY

position(transmitteron,audiomuted)ortheONposition(transmitterandaudio

bothon).TheBATTERY INDICATOR LED (28)willgiveasinglequickash,indicating

usable battery strength. In the case of a dead or low battery, the LED either will

not go on at all or will stay on continuously, indicating that the battery should be

replaced with a fresh one.

4. The microphone is now ready to use. Most or all of the RF DISPLAY LEDs (4) on

the Encore DUET receiver should now be lit, indicating a received signal from the

transmitter. When ready to speak, slide the transmitter switch to the ON position

andadjustthevolumeofthereceiveraspertheAudioOutputMicrophone

Connection section of the above Encore DUET receiver instructions. The AF LEVEL

LED DISPLAY (5)ontheEncoreDUETreceiverwilllightupto5LEDs(4green

and1red)forallinputsignals.Occasionalickeringonandoffduringuseof

the top red LED indicator in this display is normal, however if the red LED stays

on continuously, it means the signal is too loud and there is the possibility of

overloaddistortion.Re-positionthemicrophonefartherfromthesourceoradjust

the AUDIO INPUT LEVEL CONTROL (29)untiltheredLEDindicatorickersonlyonthe

loudest inputs.

(Note: Observe care in selecting P.A. volume, transmitter location and

speaker placement so that acoustic feedback (howling and screeching) will be

avoided. Please also observe the pickup patterns of the microphone selected:

omnidirectional mics pick up sound equally from all directions and are prone to

feedback if not used carefully. Unidirectional mics are more resistant to feedback,

but pick up sound sources best that are directly in front of the mic. Also, mics

that are farther from the sound source, such as lavaliers, require more acoustic

gain and thus are also more prone to feedback than close-source mics such as

handheld or headworn mics that are used close to the mouth.)

(Note: Microphone elements can easily be destroyed by the buildup of salts and

minerals from perspiration and saliva. It is good practice to put a windscreen on

the mic element at all times to protect it.)

WLT LAVALIER/LAPEL OR HEADWORN

MICROPHONE BODYPACK TRANSMITTER

OFF/STANDBY/ON

BAT

LOW

MIC

Opening Battery Compartment

Andere Handbücher für ENCORE DUET

Inhaltsverzeichnis

Andere Nady Systems Mikrofonsystem Handbücher

Nady Systems

Nady Systems MGT-16 Bedienungsanleitung

Nady Systems

Nady Systems ENCORE DUET Bedienungsanleitung

Nady Systems

Nady Systems 401X Quad Bedienungsanleitung

Nady Systems

Nady Systems DKW-8U Bedienungsanleitung

Nady Systems

Nady Systems EO3 Bedienungsanleitung

Nady Systems

Nady Systems 9E3W1KUH Bedienungsanleitung

Nady Systems

Nady Systems IRW-220X HT/LT/O - Nady Ir Wireless System Bedienungsanleitung

Nady Systems

Nady Systems U-41 QUAD Bedienungsanleitung

Nady Systems

Nady Systems U-800 Bedienungsanleitung

Nady Systems

Nady Systems DigiTRU Diversity UB-33B Bedienungsanleitung

Nady Systems

Nady Systems XR-61 Bedienungsanleitung

Nady Systems

Nady Systems UWS-1K Series Bedienungsanleitung

Nady Systems

Nady Systems DigiTRU Diversity UHF-3 Bedienungsanleitung

Nady Systems

Nady Systems Encore I Bedienungsanleitung

Nady Systems

Nady Systems ENCORE II Bedienungsanleitung

Nady Systems

Nady Systems W-1KU Bedienungsanleitung

Nady Systems

Nady Systems ENCORE 2 Bedienungsanleitung

Nady Systems

Nady Systems OCTAVO U-81 Bedienungsanleitung

Nady Systems

Nady Systems 401 Bedienungsanleitung

Nady Systems

Nady Systems Personal in Ear Monitor E03 Bedienungsanleitung

Nady Systems

Nady Systems DKW-3 GT Bedienungsanleitung

Nady Systems

Nady Systems VR-3U Bedienungsanleitung

Nady Systems

Nady Systems U-41 QUAD Bedienungsanleitung

Nady Systems

Nady Systems DKW-3 HT Bedienungsanleitung

Beliebte Mikrofonsystem Handbücher anderer Marken

Paso

Paso R824 Bedienungsanleitung

Naxa

Naxa NAM-982 Bedienungsanleitung

Motorola

Motorola PMNN4461 Bedienungsanleitung

Xvive

Xvive U3 Bedienungsanleitung

Tekon

Tekon DUOS Bedienungsanleitung

Heyuan Intelligence

Heyuan Intelligence IOT-G2S-01 Bedienungsanleitung

Devine

Devine WMD-IE Bedienungsanleitung

LG LF-D7150 Bedienungsanleitung

GE S768DAV Bedienungsanleitung

LD U305 HBH 2 Bedienungsanleitung

Chainway

Chainway URA8 Bedienungsanleitung

ORATOR

ORATOR D860TD Bedienungsanleitung

Sennheiser

Sennheiser Evolution Wireless Digital EW-DX EM 2 Bedienungsanleitung

Alpha Technologies

Alpha Technologies RBMS Bedienungsanleitung

SWIT Electronics Co.,LTD.

SWIT Electronics Co.,LTD. CW-S150 Bedienungsanleitung

Shure

Shure UA844 Bedienungsanleitung

Panasonic

Panasonic SHFX70 - DVD HOME THEATER WIRELESS SYSTEM Bedienungsanleitung

Pyle

Pyle PDWM5000 Bedienungsanleitung