Nady Systems DW-11 Bedienungsanleitung

Table of Contents................................................................... 3

Introduction............................................................................ 3

Using This Manual.................................................................. 3

System Components............................................................... 3

System Features...................................................................... 4

DW-11/DW-22 Receivers........................................................... 5

Digital HT Handheld Microphone Transmitter............................ 7

Digital LT/HM Bodypack Microphone Transmitter..................... 8

Specications............................................................................ 10

Precautions And Troubleshooting …………................................ 11

Miscellaneous Useful Tips …………........................................ 12

Warranty …………...................................................................... 13

Service…………………………………………………….................. 14

CONTENTS

Thank you for purchasing a NADY DW-11/DW-22 Digital Wireless Microphone System . I know

you will be pleased with your choice. Your system is loaded with top professional operating

features and oers the best performance and price value available in digital wireless.

With 24-bit digital audio conversion technology, low latency, and clear channel operation on the

UHF 900MHz band. This unit is simple to operate and provides interference-free performance

for any application or locale.

This booklet provides instructions for the operation of both the DW-11 Single Receiver and

DW-22 Dual Receiver Digital Wireless Systems, including handheld or lavalier/headworn mic

transmitters. Please read the instructions for your system completely before operating unit.

This manual will rst list the features of the DW-11/DW-22 systems and then will take you step

by step to show you how to operate your new system. After reading the receiver instructions,

turn to the section of the booklet that covers the type of transmitter used with your new system.

Each section will give you detailed operating instructions. Also included in this manual are

system specications and servicing information.

All System Includes

• Receiver

• Transmitter(s)

• Power Supply

• Owner’s Manual

INTRODUCTION

USING THIS MANUAL

SYSTEM COMPONENTS

DW-11 SINGLE AND DW-22 DUAL CHANNEL RECEIVERS

• User Friendly. Fixed channel and frequency make operation very simple. Just turn

the system on and it’s set to go!

• State-of-the-art, professional 24-bit digital conversion technology for exceptional

audio clarity with transparent frequency response across the entire audible range

(20Hz to 20,000Hz). The truest possible sound with undetectably low latency.

• Clear Signal operation in 900 MHz Band. Completely free from TV interference.

• Sophisticated RF ltering for optimal simultaneous operation of multiple systems in

the same location.

• Reliable long range operation. Digital transmission virtually eliminates interference

from nearby obstacles and noise from your audio. Extended operating range up to

300 feet line-of-sight.

• Sleek, rugged ABS tabletop housing for long-term durability.

• Front panel AF / RF LED displays for monitoring incoming signal strength and audio

level, backlit panel display showing pre-selected channel and operating frequency,

Power On/Off Switch, and volume Controls (DW-22 separate Ch A and Ch B controls)

• Back panel xed balanced XLR MIC level audio out (DW-22 dual XLR outs), and

adjustable ¼” LINE level out (DW-22 single MIXED SUM adjustable line out), DC

input jack, and rotatable, swivel attached antenna (DW-22 dual antennas).

• Externally powered with included universal voltages 110V-220V AC / 13.5 VDC

regulated 400mA adapter.

• Optional RMT-1KUD available for rack mounting single or dual DW-11/DW-22

receivers.

TRANSMITTERS

• Choice of DIGITAL HT™ Handheld Microphone, and DIGITAL LT™ Bodypack

Transmitter for operation with lavalier or headworn mics.

• Digital HT™ features the unidirectional neodymium dynamic cartridge for optimum

true sound, maximum feedback rejection and minimal handling noise. Sleek rugged

housing, battery status LED display, On /Off switch and internal antenna for optimum

aesthetics.

• Digital LT™ features compact housing, removable belt clip, durable attached external

antenna, unique locking 3.5mm mini jack for connecting lavalier or headworn mics,

and On/ Standby (Mute) / Off switch which provides convenient audio muting with the

transmitter on

• Convenient, economical operation with (2)AA alkaline batteries.

SYSTEM FEATURES

1. Rack mounting The Receivers

There are 2 options available for rack mounting the DW-11/DW-22 receivers: singly or

side-by-side with another DW-11/DW-22 Series receiver. A single DW-11 or dual DW-22

receiver can be rack mounted with the optional RMT-1KUD rack tray.

[ Note: Do not mount the receiver in a rack directly above an amplier or other source of high

heat – this could degrade the performance of the DW-11/DC-22. Always ensure adequate

airow and heat dissipation in any rack conguration.]

2. Powering The Receivers

Plug the AC/DC ADAPTER provided into the DC INPUT JACK (9) on the back of the

receiver. Then plug the power supply into an AC outlet.

[ Note: Any 13.5V DC regulated source with 400mA capability can also be used.]

Press the POWER SWITCH (2) once to turn on the receiver. The POWER ON LED (1)

will now light and the receiver is operational.

3. Antennas

The DW-11/ DW-22 receivers are supplied with ATTACHED ANTENNAS (10). As these

antennas are rear mounted, position them in the rack so the antennas can be adjusted

fully to obtain maximum range. Optimal antenna position is 45 degrees from the receiver

(at 90 degrees from each other). For maximum range, it is always best to maintain a line-

of-sight (no obstructions) between the receiver antennas and the transmitter at all times

whenever possible.

4. Connecting the Audio Output

The DW-11 and DW-22 receivers provide both a xed Mic level BALANCED XLR (7)

AUDIO OUTPUT and an adjustable line level UNBALANCED LINE/MIX 1/4” jack (8)

AUDIO OUTPUT. Both ¼” and XLR outputs can be used at the same time. VOLUME

CONTROL (6) is for UNBALANCED LINE/MIX 1/4” jack (8) AUDIO OUTPUT only (p 6).

5. Microphone Connection

Either the BALANCED XLR (7) or the UNBALANCED LINE/MIX OUT1/4” (8) can be used.

The BALANCED XLR (7) audio output is set at a non-adjustable microphone level, similar

to hardwired Mic levels. Adjust volume level from your amplier or mixing board. Plug an

XLR connector into the XLR output socket on the rear of the unit and plug the other end

into your amplier or mixing board. Make sure the phantom power on your mixing board

is turned off and the volume is turned down when making connections. To use the 1/4”

UNBALANCED LINE/MIX OUT(8) socket, follow the instructions for connecting (above),

except start the receiver volume at 1/2 MAX and adjust until the volume level is optimal. If

the volume control is set too high, you may overload your mixer or amp.

[ Note: As when making any connection, make sure the amplier or mixing board volume is at

the minimum level before plugging in the receiver to avoid possible sound system damage.]

DW-11/DW-22 RECEIVERS

RECEIVER OPERATION

DW-11 and DW-22 Receiver Front and Back Label

6. LED Display

The DW-11/DW-22 receivers are equipped with AF LED indicator (4) showing the

audio present from the transmitter. If this LED lights continuously, decrease the volume

to the Mic or overload distortion may result. The RF LED DISPLAY (3) showing the

TRANSMITTERS(TX) is on. When it is lit up, the TX is in usable range. If not lit up or

ickering, either the TX is not on or it is out of range. Move the TX closer to re-establish

the connection.

1. Power On Indicator 2. Power On/Off Switch 3. RF On Indicator

4. AF On Indicator 5. Frequency Label Screen 6. Volume Control

7. Balanced XLR Out 8. Unbalanced ¼” LINE/MIX Out 9. DC Input Jack

10. Antenna

DIGITAL HTTM

11. Windscreen 12. Battery Good/Low LED Indicator

13. Power On/Off 14. Battery Cover

15. Battery Compartment / 2 AA Batteries LT

DIGITAL HTTM HANDHELD MICROPHONE TRANSMITTER

HANDHELD OPERATION

1. Unscrew the BATTERY COMPARTMENT COVER (14) and insert 2 fresh AA

ALKALINE BATTERIES into the BATTERY COMPARTMENT(15), observing the

correct polarity as marked. Screw the cover back on to the microphone. Fresh alkaline

batteries can last up to 11 hours in use, but in order to ensure optimum performance,

it is recommended that you replace the batteries after every 8-10 hours of use.

2. Turn on the DIGITAL HT™ by sliding the POWER SWITCH (13) to turn on the

TX rst. The RF LED (3) on the DW-11/DW-22 receivers should now be lit, indicating

a received signal from the transmitter. The BATTERY INDICATOR LED (12) will

give a single quick ash, indicating usable battery strength. In the case of a dead or

low battery, it will either not go on at all or will stay on continuously, indicating that

the batteries should be replaced with fresh ones. To preserve battery life, turn the

transmitter off when not in use.

3. The microphone is now ready to use. Adjust the volume of the receiver per the

Audio Output Microphone Connection section above.

[Note: Observe care in selecting P.A. volume, transmitter location and speaker place-

ment so that acoustic feedback (howling or screeching) is avoided.]

DIGITAL LT/HMTM

16. Antenna 17. Power On/Off, Audio Mute

18. Mic Input 19. Battery Good/Low and RF LED Indicator

20. Belt Clip 21. Battery Compartment

22. Battery Cover 23. LT/HM Mics

DIGITAL LT/HMTM BODYPACK TRANSMITTER

BODYPACK OPERATION

1. Open the hinged BATTERY DOOR (22) and insert 2 fresh AA ALKALINE

BATTERIES into the BATTERY COMPARTMENT (21), observing the correct polarity.

Fresh alkaline batteries can last up to 11 hours in use, but in order to ensure optimum

performance, it is recommended that the batteries be replaced after 8-10 hours of use.

2. Turn on the DIGITAL LT™ by sliding the POWER SWITCH (17) to audio MUTE

position rst. The RX RF LED INDICATOR (19) will turn on. The BATTERY INDICATOR

LED (19) will give a single quick ash, indicating usable battery strength. In the case of

a dead or low battery, it will either not go on at all or will stay on continuously, indicating

that the batteries should be replaced with fresh ones. To preserve battery life, turn the

transmitter off when not in use.

3. The microphone is now ready to use. When ready to speak, slide the audio POWER

SWITCH (17) to the ON position. The RF LED (19) on the DW-11/DW-22 receivers

should now be lit, indicating a received signal from the transmitter. Adjust the volume

of the receiver per the Audio Output Microphone Connection section above.

[Note: Observe care in selecting P.A. volume, transmitter location and speaker placement

so that acoustic feedback (howling or screeching) is avoided.]

DW-11 and DW-22 Receiver Back

( showing the connection )

DIGITAL LT/HMTM BODYPACK TRANSMITTER

4. The DIGITAL LT™ is provided with a 3.5 mm LOCKING JACK (18) for connecting

the audio input selected. Connect either HEADWORN MIC or LAVALIER MIC CORD

(23) as desired, according to the model selected.

[ Note: Use only the input selected or the audio will not be optimal–a muddy or distorted

sound may result. To secure the connection, turn the slip ring on the plug clockwise to

thread it on the jack. To unplug, reverse the process.]

Slip the transmitter into a pocket or BELT CLIP (20) on to your clothes.

5. Microphone Use (with either a Lavalier or Headworn microphone)

Secure the connection from the LAVALIER or HEADWORN MIC CORD(23) by turning

the slip ring on the plug into the transmitter clockwise to thread it onto the jack. To

unplug, reverse the process. To use the Lavalier Mic, attach it at chest level. Do not

place it too close to the mouth–a distance of about six inches usually works best. To

use the head worn Mic, place it on the head and adjust the boom so that the Mic is

about one inch to the side of the front of the mouth.

[ Note: Observe care in selecting P.A. volume, transmitter location and speaker placement

so that acoustic feedback (howling and screeching) is avoided. Also note the pickup pattern

characteristics of the microphone selected: Omnidirectional mics pick up sound equally

from all directions and are prone to feedback if not used carefully. Unidirectional Mics are

more resistant to feedback, but pick up sound sources best that are directly in front of the

Mic. Mics that are farther from the sound source, such as lavaliers, require more acoustic

gain and thus are also more prone to feedback than close-source Mics such as handheld

or headworn models that are used close to the mouth. ]

6. Sample Connections: Connect ¼” output for A and B Channels to Mixer inputs.

Use the volume to set for optimum output. VOLUME CONTROL (6) is for LINE/MIX

1/4” jack (8) AUDIO OUTPUT only. For separate control, use XLR outputs to each

Mixer input, control the level from the Mixer. Power adapter connection as shown in

the picture below.

RECEIVER OVERALL SYSTEM PERFORMANCE

Frequency Response: 20Hz – 20,000Hz +/-3dB

Dynamic Range: 120dB (A-weighted)

Total Harmonic Distortion: <0.1%

Latency: 3mSec (48 kHz Sample Rate)

RF Carrier Frequency Range: Selected frequencies between 902 and 951MHz

Frequency Stability: +/- 20PPM, PLL controlled

Modulation: Digital QPSK

Operating Range: Up to 300 ft. typical (depending on site conditions);

optimum line-of- sight

DW-11/DW-22 RECEIVERS

Reception : External 7.25” (18.5cm) Antenna Attached

(DW-22 – dual antennas)

Receiver Sensitivity : -94dBm

Controls : Power ON/OFF, Volume Control

Connectors : 1/4” (6.35 mm) Unbalanced phone jack (360 mV/ no load)

XLR Balanced output (+/-12 mV/600 Ohm load)(2x for DW-22)

LED Indicators : Power ON, RF/AF LEDs

Unwanted Signal Rejection : 60dB image and spurious

Power Requirements : DC 13.5V Regulated @ 400mA

DC input : 2.1mm jack

Weight and Dimensions : DW-11: 0.75lbs (340g)

8” X 6” X 1.75” (203 X 152 X 44mm)

DW-22: 0.8lbs (363g)

8” X 6” X 1.75” (203 X 152 X 44mm)

DIGITAL HT™/DIGITAL LT™ TRANSMITTERS

RF Power Out : +13dBm, (50mW maximum allowed by FCC)

RF Spurious Emissions : < –50 dB

Audio Inputs : Digital HT™ Integral neodymium dynamic cartridge

Digital LT™ Bodypack : 1/8” (3.5mm) locking mini-jack, for headworn or

lavalier Mic

CONTROLS

HT/LT : Power On/Off, (LT) Audio Mute

LED Indicator : Unit on (single ash), Low Battery Alert (red)

Battery Type : 2 AA Alkaline

Battery Life : Up to 11 Hours

Weight and Dimensions : Digital HT™: 0.6lbs (272g) / 9.25”(L) X 2”(dia.)

Digital LT™: 0.15lbs (68g)/ 2.5” X 4.25” X 0.5”

(64 X 108 X 13mm)

OPTIONAL ACCESSORIES

RMT-1KUD rack tray for rackmounting either one or two DW-11/DW-22 receivers.

SPECIFICATIONS

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Nady Systems Mikrofon Handbücher

Nady Systems

Nady Systems SCM 900 Bedienungsanleitung

Nady Systems

Nady Systems STARPOWER SP-33 Bedienungsanleitung

Nady Systems

Nady Systems STARPOWER SP-33 Bedienungsanleitung

Nady Systems

Nady Systems SPC-15 Bedienungsanleitung

Nady Systems

Nady Systems SPC-20 Bedienungsanleitung

Nady Systems

Nady Systems RSM-1 Bedienungsanleitung

Nady Systems

Nady Systems TCM 1050 Bedienungsanleitung

Nady Systems

Nady Systems STARPOWER Series Bedienungsanleitung

Nady Systems

Nady Systems SP-9 Bedienungsanleitung

Nady Systems

Nady Systems CM 88 Bedienungsanleitung

Nady Systems

Nady Systems CM 88 Bedienungsanleitung

Nady Systems

Nady Systems HM-10 Headmic Bedienungsanleitung

Nady Systems

Nady Systems DM 70 Bedienungsanleitung

Nady Systems

Nady Systems SPC-15 Bedienungsanleitung

Nady Systems

Nady Systems STARPOWER SPR3 Bedienungsanleitung

Nady Systems

Nady Systems SCM 700 Bedienungsanleitung

Nady Systems

Nady Systems SCM 960 Bedienungsanleitung

Nady Systems

Nady Systems SCM 1000 Bedienungsanleitung

Nady Systems

Nady Systems HM-35 Bedienungsanleitung

Nady Systems

Nady Systems RSM-2 Bedienungsanleitung

Nady Systems

Nady Systems CM-2S Bedienungsanleitung

Nady Systems

Nady Systems RSM-4 Bedienungsanleitung

Nady Systems

Nady Systems SCM 800 Bedienungsanleitung

Nady Systems

Nady Systems OHCM-200 Bedienungsanleitung

Beliebte Mikrofon Handbücher anderer Marken

IK Multimedia

IK Multimedia iRig Stream MIC PRO Bedienungsanleitung

DAPAudio

DAPAudio RM-101 Bedienungsanleitung

AKG

AKG CHM 21 Bedienungsanleitung

Sennheiser

Sennheiser evolution wireless series EM 100 Bedienungsanleitung

Sony

Sony C-48 Bedienungsanleitung

GIGAMEDIA

GIGAMEDIA GGM PAMICUHFG Bedienungsanleitung

Shure

Shure WH30TQG Bedienungsanleitung

auna PRO

auna PRO MIC-900 Bedienungsanleitung

AKG

AKG D 3800 Bedienungsanleitung

Shure

Shure KSM141 Bedienungsanleitung

MAIIN SOUND

MAIIN SOUND IIN style Bedienungsanleitung

Earthworks

Earthworks TC25 Bedienungsanleitung

Sennheiser

Sennheiser evolution D1 Bedienungsanleitung

Alesis

Alesis MicLink Wireless Bedienungsanleitung

DSPPA

DSPPA D6234 Bedienungsanleitung

Monacor

Monacor IMG STAGELINE ECM-300B Bedienungsanleitung

Ansr Audio

Ansr Audio Scan16 Bedienungsanleitung

Shure

Shure MXA710 Series Bedienungsanleitung