NAPCO GEM-DXRP2 Bedienungsanleitung

OPERATING GUIDE for your

GEM-DXRP2 KEYPAD

AC ON READY

The GEM-DXRP2 is a “smart” user-

friendly, interactive menu-driven keypad

designed for your Napco control panel.

Its alphanumeric screen will not only

display the status of your system, but will

also give you step-by-step instructions to

guide you through all operations.

This booklet contains important

information about the operation of your

system with this GEM-DXRP2 Keypad.

Read it carefully and keep it handy for

future reference. Check the Glossary for

an explanation of terms that may be

unfamiliar to you.

You'll probably find subjects

mentioned in this booklet that do not

apply to your system. Napco control

panels have such a wide variety of

features that few security systems, if

any, will ever need them all. Your

alarm professional has chosen

appropriate features for your particular

needs.

Regardless of how your system has

been configured, rest assured that it has

been carefully designed and engineered

to the highest industry standards. To

assure optimum safety and security,

familiarize yourself with this equipment.

Periodically check its condition and state

of readiness by testing it at least once a

week in both the ac/battery and battery-

only modes (ask your alarm professional

how to make these tests).

INTRODUCTION

IMPORTANT - TEST YOUR SYSTEM WEEKLY

Test your sounding device.

1. While disarmed, enter your User Code and press A.

2. Answer NO (press F) until “Bell Test Yes/No” appears in the

window.

3. Press YES (E) to execute the test. The alarm will sound for

about two seconds.

•If the alarm does not sound or sounds weak, call for service.

Test your telephone line

(Turn On Telephone Test programmed? YES NO)

1. Notify your Central Station of the impending test.

2. While disarmed, enter your User Code and press A.

3. Answer NO (press F) until “TurnOn TelTst Yes/No" appears in

the window.

4. Press YES (E) to send a test code to the central station.

•If the test is not successful, “E03 COMMFL” will display, indicating

a communication failure. Call for service.

Note: Any subsequent successful transmission will clear an “E03

COMMFL” system trouble.

TABLE OF CONTENTS

Section Page

KEYPAD CONTROLS & INDICATORS............................................ 4

SETTING THE ALARM (ARMING) WHEN LEAVING....................... 6

PROTECTING YOURSELF WHILE ON THE PREMISES ................ 9

TURNING OFF THE ALARM (DISARMING) WHEN RETURNING... 11

FIRE PROTECTION......................................................................... 13

KEYPAD FUNCTIONS ..................................................................... 17

CENTRAL-STATION MONITORING ................................................ 22

ADVANCED FEATURES ................................................................. 23

PROGRAMMING ............................................................................. 25

KEYPAD MESSAGES...................................................................... 28

GLOSSARY ..................................................................................... 32

SYSTEM TROUBLE ERROR CODES ............................................. 35

TO SILENCE AN ALARM, ENTER YOUR

CODE, AND PRESS J.

FOR SERVICE, CALL: _____________________

CENTRAL STATION: _____________________

EXIT DELAY: ___________________________

ENTRY DELAY: _________________________

FIRE ALARM SOUND*:

_____________________________________

BURGLAR ALARM SOUND*:

_____________________________________

KEYPAD FIRE ENABLED? YES NO

KEYPAD PANIC ENABLED? YES NO

KEYPAD AUX. ENABLED? YES NO

*FIRE HAS PRIORITY OVER BURGLARY.

KEYPAD CONTROLS & INDICATORS

AC ON READY

KEYPAD CONTROLS & INDICATORS

Window. Displays system status

messages, zone descriptions, etc.

STATUS Light. Lights (green) to

indicate that the system is ready

for arming. If a zone is not

secured the light will be off and

the zone will display in the

window. If a zone has been

bypassed, the STATUS light will

blink while armed.

ARMED Light. Lights (red) to

indicate that the system is armed.

If an alarm has occurred, the

ARMED LED will be flashing.

FUNCTION Button. Selects

available system functions as

displayed in the window. The

selected function is executed by

pressing the Jto button.

BYPASS Button. (1) Deactivates

selected zones from the system.

(2) Unbypasses a bypassed zone

(GEM-P3200/9600 panels only).

RESET Button. (1) Resets

various system troubles, displays,

etc. (See text.) (2) Resets

residential smoke detectors.

Numerical Keys (1-9, 0). Used to

enter codes, zone numbers, etc.

ON/OFF Button. Entry key.

Causes the entered code or

selected function to be executed.

INTERIOR Button. (1) Bypasses

all Interior Zones simultaneously

to allow free movement within the

premises. (2) Scrolls the window

display forward (NEXT). (3)

Answers “YES” to questions in

the window display.

INSTANT Button. (1) Cancels

entry delay on Exit/Entry Zones,

causing an instant alarm upon

violation. (2) Scrolls window

display backward (PRIOR). (3)

Answers “NO” to questions in the

window display.

AREA Button (*). Selects other

areas and is used with

emergency buttons.

Emergency Buttons. Used with

the Gbutton to signal an

emergency, as follows:

Press the 7and the G

buttons for Fire Emergency.

Press the 8and the G

buttons for Auxiliary Emergency.

Press the 9and the G

buttons for Police Emergency.

SETTING THE ALARM (ARMING) WHEN LEAVING

ZONES FAULTED

02 BACK DOOR

BYPASSED BYPASSED

BYPASSED 02 BACK DOOR

Arming the System

Note: The keypad will autoscroll messages that are longer than one line.

1Check the keypad. The green STATUS light must be on in order to arm. If the

green light is off, “FAULT” will display in the window followed by the number of

each faulted zone. Note each problem zone and secure it by closing a window,

door, etc. When all zones are secure, the green STATUS light will turn on and the

window will display “READY”.

Bypass faulted zones. If you cannot locate or repair the problem yourself, call

for assistance. If you cannot get immediate help, bypass the problem zone(s)

from the system by pressing B, then the zone number (or vice versa). Note:

Bypassed zones are unprotected. If armed with zones bypassed, be sure to have

the system checked as soon as possible.

2Arm the system. Enter your code and press J. The green STATUS light will go

off, the red ARMED light will turn on and the window will alternately display “EXIT"

and "XX SEC" (where “XX” represents the exit time remaining, in 10-second

steps). Note: If you enter an invalid code, the keypad will display “Wrong Code”.

3Leave the premises. Leave through the exit door before exit time expires.

AC ON

READY

AC ON

FAULT/

ZONE 02

BYPASSED AC ON

READY

AC ON

EXIT/

XX SEC

SETTING THE ALARM (ARMING) WHEN LEAVING

Priority Arming. If you attempt to arm with a faulted Priority Zone, a 3-second tone will

sound at the keypad, and "CAN'T/ArmZnF" will display in the window, indicating that

the trouble(s) must be corrected before the panel can be armed. A zone selected as

Priority Zone with Bypass (check your Alarm Plan) may be bypassed if in trouble. If

the problem cannot be corrected immediately, press C, then arm the panel. A 3

second beep will sound at the panel to indicate arming with a Priority Zone in trouble.

Be sure to have the trouble repaired as soon as possible.

Silence Alarm. If you enter your code while the alarm is sounding the message

"CAN'T/ArmSil" will be displayed. The system will silence the alarm and will be ready

to be armed again.

Alarm Sounding. If you are attempting to arm with Easy Arm (Optional) and the alarm

is sounding, "CAN'T ArmSnd" will be displayed. The alarm will not silence. Only a

valid User Code will silence the alarm.

System Trouble. If you enter your User Code with a system trouble present, the mes-

sage "CAN'T ArmRst" will be displayed. To arm, press Cand the system trou-

bles should disappear.

AC ON

CAN'T/

ArmZnF

AC ON

CAN'T/

ArmSil

AC ON

CAN'T/

ArmSnd

TROUBLE

AC ON

CAN'T/

ArmRst

SETTING THE ALARM (ARMING) WHEN LEAVING

If you attempt to arm with a “TROUBLE” display (alternating with a system trouble error code), a 3-

second tone will sound at the keypad. (See SYSTEM TROUBLE ERROR CODES for descriptions

of codes). The window will display “CAN'T ArmRst”. If you cannot correct the problem

immediately, pressing Cwill enable you to arm in this condition. Be sure to call for service as

soon as possible.

Area Arming (Optional)

Some systems may be divided, or partitioned, into smaller independent subsystems, which are

referred to as Areas. In a system that has been partitioned into multiple areas, one or more area

may be armed while others remain disarmed. In a multi-area system, the area number will be

indicated by the right-most digit.

Manager's Mode The Manager's Mode, if enabled, provides quick access to other areas without

the system status display. (This is NOT a high-security feature).

To arm any area:

1. Press the numerical key representing the area number.

2. Press Gfollowed by J. In effect, you will now "be" in that area.

3. Enter your User Code followed by Jto arm or disarm the area. Note: Your code must be

valid in that area.

4. Press Gfollowed by Jto return to the home area.

Global Arming (Optional) (Not available with GEM-P1632/816 panels)

To arm all areas simultaneously, press 9,Gand enter your code followed by J.

To disarm all areas simultaneously, press 0, Gand enter your code followed by J.

If any zone is not secured, the keypad will alternately display "CAN'T ARM / AREA #", where

"#" identifies the number of the area(s) in trouble. All problem zones in the respective area(s)

must be secured or bypassed before the area can be armed. Note: If a system trouble is

indicated, the system cannot be armed using this method.

TROUBLE

AC ON

TRBL

EXX-XX

TROUBLE

AC ON

CAN'T/

ArmRst

AC ON

READY1

AC ON

CAN'T/ARM/

AREA#

Bypassing Interior Zones

Interior Zones, when bypassed, allow free movement within the premises while the protection of

armed perimeter zones is maintained. If Eis pressed, all interior Zones will be bypassed upon

arming.

(OPTIONAL) Some control panels (such as the GEM-P9600) have provisions for TWO groups of Interior Zones. If two groups of zones were

programmed, proceed as follows:

1. Select the interior group by repeatedly pressing E. The window will display "INT1". "INT2",

or "INT1+2".

2. When the desired interior group is displayed, press Dto select it. "BYPASSED" and

"INTERIOR" will display to indicate interior zones bypassed.

3. Enter your code, then press D. The red ARMED light will turn on and the green STATUS light

will blink, indicating zones bypassed. After the exit time has elapsed, the window will display

"ARMED" and "BYPASSED INTERIOR" will be displayed.

Automatic Interior Bypass (Optional - Automatic Interior Bypass programmed? YES NO)

Your system may have been programmed for Automatic Interior Bypass, which allows it to recognize

that you have armed the system and remained in the house, prompting it to automatically bypass

any Interior Zones. In this case, the keypad display will normally show the icon "BYPASSED", ex-

cept when the system is armed, and the Exit Entry door is opened. At this time those Interior Zones will unbypass, providing complete interior

protection.

Easy Exit (Optional - Available on systems containing Interior Zones).

While the system is armed in the Automatic Interior Bypass state, the Easy Exit option is available. To exit the premises while the system is

armed, press Dand the Exit Delay countdown will begin. You can now exit the premises through the Exit/Entry door and the system will return

to the armed state when the countdown expires.

PROTECTING YOURSELF WHILE ON THE PREMISES

BYPASSED INTERIOR

AC ON

READY

AC ON INT1+2

BYPASSED INTERIOR

AC ON

READY

BYPASSED INTERIOR

AC ON

ARMED

BYPASSED

AC ON

READY

PROTECTING YOURSELF WHILE ON THE PREMISES

Instant Protection

When retiring for the evening, after all family members are home, you can cancel the

entry delay on the Entry Zone(s). Then, when armed, opening the entry door will cause

an immediate alarm. (When arming, exit delay will remain in effect).

1. To cancel the entry delay while on the premises, merely press F. (The Fbutton may be pressed either before or

after arming).

2. When armed, the window will display "ARMED", and "INSTANT ON" and the red ARMED light will flicker rapidly to indicate

instant protection.

Emergency Buttons (Only available if programmed)

The Blue Emergency Buttons (7,8& 9), if programmed, are always active,

whether the system is armed or disarmed. The emergency signal will only be transmitted

when an Emergency Button and Gare pressed at the same time.

•Fire Emergency Simultaneously press 7and Gto alert the central station of a fire

emergency. *(Fire Emergency programmed? YES NO)

•Auxiliary Emergency Simultaneously press 8and Gto alert the central station of

an Auxiliary emergency. *(Auxiliary Emergency programmed? YES NO)

•Police Emergency Simultaneously press 9and Gto alert the central station of a

police emergency. *(Police Emergency programmed? YES NO)

INSTANT ON

AC ON

ARMED

Inhaltsverzeichnis

Andere NAPCO Tastenfeld Handbücher

NAPCO

NAPCO RPXP6GT Bedienungsanleitung

NAPCO

NAPCO Magnum Alert Bedienungsanleitung

NAPCO

NAPCO RP1054e Bedienungsanleitung

NAPCO

NAPCO Gemini GEM-K4RF Bedienungsanleitung

NAPCO

NAPCO Gemini GEM-RP3DGTL Bedienungsanleitung

NAPCO

NAPCO Gemini GEM-K1CA Bedienungsanleitung

NAPCO

NAPCO Gemini GEM-RP3DGTL Bedienungsanleitung

NAPCO

NAPCO GEM-RP8LCD Bedienungsanleitung

NAPCO

NAPCO GEM-RP8LCD Bedienungsanleitung

NAPCO

NAPCO Gemini GEM-P1632 Bedienungsanleitung

NAPCO

NAPCO Gemini GEM-K2AS Bedienungsanleitung

NAPCO

NAPCO MAGNUM ALERT RP2000 KEYPAD Bedienungsanleitung

NAPCO

NAPCO MAGNUM ALERT RP1016E KEYPAD Bedienungsanleitung

NAPCO

NAPCO RP1000LCD Bedienungsanleitung

NAPCO

NAPCO RP1016LCD Bedienungsanleitung

NAPCO

NAPCO Magnum Alert RP1000ELCD Bedienungsanleitung

NAPCO

NAPCO Magnum Alert RP1000ELCD Bedienungsanleitung

NAPCO

NAPCO MAGNUM ALERT RP1016 LCD KEYPAD Bedienungsanleitung

NAPCO

NAPCO GEMINI GEMC-255 Bedienungsanleitung

NAPCO

NAPCO Gemini GEM-P816 Bedienungsanleitung

NAPCO

NAPCO RP1054e Bedienungsanleitung

NAPCO

NAPCO RP1016LCD Bedienungsanleitung

NAPCO

NAPCO iSecure ISEC-WL-KEYPAD Bedienungsanleitung

NAPCO

NAPCO Gemini GEM-TOUCH K Series Bedienungsanleitung

Beliebte Tastenfeld Handbücher anderer Marken

BFT

BFT SELETTO Bedienungsanleitung

Micro Id

Micro Id MP7G3BL Gebrauchsanweisung

WindowMaster

WindowMaster WLI 130 Bedienungsanleitung

ACT

ACT ACT PRO 1030 Bedienungsanleitung

Cardin

Cardin SSB Series Bedienungsanleitung

Harman Kardon

Harman Kardon KP 1 Bedienungsanleitung

Chamberlain

Chamberlain KPR2000 Benutzerhandbuch

CYP

CYP CR-KP1 Bedienungsanleitung

Aeware

Aeware k-35 Series Referenzhandbuch

Aritech

Aritech CS-175 Series Bedienungsanleitung

GE NetworX NX-1600E Series Bedienungsanleitung

Lenze AC Tech

Lenze AC Tech MC SERIES Bedienungsanleitung

Burg Wächter

Burg Wächter secuENTRY 7711 Bedienungsanleitung

Aeware

Aeware in.k450 Bedienungsanleitung

Lenze

Lenze EPM-H410 Bedienungsanleitung

Toshiba

Toshiba RKP007Z Bedienungsanleitung

Gemini

Gemini GEM-DXK1 KEYPAD Bedienungsanleitung

Russound

Russound MDK-C5 Betriebsanleitung