Napoleon Dynamic Heat Control Bedienungsanleitung

FRENCH PG. 27

W415-2753 / A / 07.20.20

ADD MANUAL TITLE

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone 1 (866) 820-8686 • www.napoleon.com • [email protected]

CERTIFIED TO THE CANADIAN AND AMERICAN NATIONAL STANDARDS:

CSA 2.22 AND ANSI Z21.50 FOR VENTED DECORATIVE GAS APPLIANCES

INSTALLER:

Leave this manual with the appliance

CONSUMER:

Retain this manual for future reference

ADD PRODUCT CODE HERE (TRADE GOTHIC LT STD FONT)

NATURAL GAS MODELS:

PROPANE GAS MODELS:

Product Name / Code

(MUST use title from Price Book)

ADD ____ ILLUSTRATED

ADD PRODUCT IMAGE

CSA /

INTERTEK

LOGO

SAFETY INFORMATION

- Do not store or use gasoline or other

ﬂammable vapors and liquids in the vicinity of

this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not

use any phone in your building.

• Immediately call your gas supplier from a

neighbour’s phone. Follow the gas

supplier’s instructions.

• If you cannot reach your gas supplier, call

the ﬁre department.

- Installation and service must be

performed by a qualiﬁed installer, service

agency, or the supplier.

This appliance may be installed in an aftermarket,

permanently located, manufactured home (USA

only) or mobile home, where not prohibited by

local codes.

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is

not convertible for use with other gases, unless

a certiﬁed kit is used.

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly

could result in serious injury, death, or

property damage.

WARNING

ENGLISH

$10.00

FOR INDOOR USE ONLY

IF INSTALLATION + OPERATION, ADD SERIAL

NUMBER LABEL HERE

IF SEPARATE MANUALS, ADD “PLACE

BARCODE LABEL ON THE OWNER’S MANUAL”

INSTALLATION MANUAL

FOR INDOOR USE ONLY

FOR USE WITH ELEVATION™ X

MODELS ONLY

These installation instructions MUST be used in conjunction with the Elevation™ installation manual.

(Installation Option 2 illustrated)

Dynamic Heat Control™

air outlet opening

W415-2753 / A / 07.20.20

table of contents

The information throughout this manual is believed to be correct at the time of printing. Wolf Steel

Ltd. reserves the right to change or modify any information within this manual at any time without

notice. Changes, other than editorial, are denoted by a vertical line in the margin.

note:

WARNING:

This product can expose you to chemicals including chromium, which are

known to the State of California to cause cancer, and chemicals including toluene, which are

known to the State of California to cause birth defects or other reproductive harm.

For more information, go to www.P65Warnings.ca.gov.

1.0 general information 3

2.0 installation planning 4

2.1 installation option 1 - open enclosure (enclosure stops short of the ceiling) 5

2.2 installation option 2 - front opening 5

2.3 installation option 3 - rear opening 6

2.4 installation option 4 - open enclosure with hard combustible valance 7

2.5 installation option 5 - side openings 8

3.0 appliance overview 9

4.0 Dynamic Heat Control™ installation 10

4.1 high limit switch installation 13

5.0 minimum framing dimensions 15

6.0 minimum clearance to combustible enclosures 16

7.0 rough framing - before appliance installation 17

8.0 finish framing - after appliance installation 18

9.0 finishing 20

9.1 enclosure design 21

9.2 optional trim ﬁnishing 22

10.0 minimum combustible mantel clearances 23

11.0 maximum protrusion 24

12.0 Dynamic Heat Control™ installation checklist 25

W415-2753 / A / 07.20.20 3

general information

1.0 general information

!WARNING

• Dynamic Heat Control™ MUST be installed during the installation of the appliance BEFORE appliance venting and gas

are installed.

• Ensure the appliance is completely cool before starting installation.

• To avoid danger of suffocation keep the packaging bag away from babies and children. Do not use in cribs, bed, carriages,

or play pens. This bag is not a toy. Knot before throwing away.

Dynamic Heat Control™ is a system for man-

aging the heat produced by the appliance at and

around the ﬁreplace. The purpose of the Dynamic

Heat Control™ is to move the heat away from

the ﬁreplace to allow it to circulate more effectively

within the living space. By installing the Dynamic

Heat Control™ both the installer and the user gain

considerable beneﬁts, see the following;

Installer:

• Ability to use combustible framing and ﬁnishing right up to the ﬁreplace opening.*

• High temperatures above the front of the ﬁreplace opening are signiﬁcantly reduced eliminating potential degrading

to sensitive ﬁnish material (cracks or discoloration).

• No additional electrical, fans, ducts, or manifolds are required which keeps installation straightforward.

User:

• Heat is circulated more consistently throughout the living space increasing comfort in front of the ﬁreplace.

• Increased “real world” efﬁciency as heat is moved into the room rather than retained inside the enclosure.

• Complete ﬂexibility in selection of ﬁnish materials.

• Ability to place a TV, sound bar or artwork above the ﬁreplace.**

The Dynamic Heat Control™ system relies on an optimized ﬂow of air both through the appliance and the enclosure.

As such the installation of the Dynamic Heat Control™ system requires certain technical considerations when com-

pared to traditional ﬁreplaces. Speciﬁcally, the Dynamic Heat Control™ requires the enclosure to be ventilated and

requires the installer to ensure that a minimum air outlet opening area is provided to allow heat to escape and circulate

at a prescribed minimum height and position. This must be carefully adhered to in the planning and the installation to

ensure the appliance functions safely and to minimize installation time.

*In most common installation conﬁgurations, some speciﬁc installations require special provisions.

See “minimum clearance to combustible enclosures” section for details. Ensure to strictly adhere to in-

structions.

** Always check appliance manufacturers’ recommendations to conﬁrm suitability and any special

environmental limitations. For valuable or antique items, always refer to expert preservation instructions as

some items require speciﬁcally controlled temperature and/or humidity.

You will need: Included in this kit

Deﬂector

High Limit Switch

Wire Harness

Bracket

Screws

W415-2753 / A / 07.20.20

installation planning

2.0 installation planning

!WARNING

• Do NOT cover or place any items in the Dynamic Heat Control™ air outlet. Failure to comply with these instructions will

create a ﬁre hazard.

• Ensure air ﬂow within the air passage is not restricted in any way with the exception of approved venting.

2 x 6

enclosure top and/or ceiling

Dynamic

Heat Con-

trol™ air

outlet opening

3 1/2”

Header

Standoff

Front

Frame

Dynamic

Heat Con-

trol™ air

outlet opening

No materials of any type

are permitted in this area

except wiring. Wiring must

come in on one side or

the other, and must not

cross the appliance and

be at least 7” from the

centre of the venting.

Air ﬂow in the shaded area must not be restricted in any way with the exception of an approved appliance vent

system. No other items are allowed in this area.

Deﬂector

Clearance to Fire Sprinkler

If there is a ﬁre sprinkler system installed in close proximity to the air outlet opening of your appliance, the following

installation parameters must be adhered by:

• Follow the sprinkler head manufacturer’s instructions regarding proximity to heat sources.

• In the absence of speciﬁc requirements, a minimum 60” (152cm) recommended clearance, in length, between

any point of the air outlet opening and ﬁre sprinkler head.

• Verify the sprinkler head sensor is set to proper heat settings to prevent activation during appliance operation

(see ﬁre sprinkler manufacturer’s instructions).

• If in doubt it is recommended to measure the temperature adjacent to the sprinkler head during installation,

after the appliance has been operating continuously for at least 2 hours.

• Follow local building codes to ensure compliance.

Typical Installation Recessed Installation

6”

MAX

W415-2753 / A / 07.20.20 5

installation planning

2.1 installation option 1 - open enclosure (enclosure stops short of the ceiling)

2.2 installation option 2 - front opening

NOT suitable for Dynamic Heat Control™ Plus

ceiling

2-4”

6” min.

DYNAMIC HEAT

CONTROL™ AIR

OUTLET OPEN-

ING IS HOT WHEN

APPLIANCE IS

OPERATING!

Air outlet opening

must be located out of reach of

the user. Air outlet must not be

restricted by furnishings or decor. RECOMMENDED

Wall mounted

object (picture

frame, appli-

ance, etc.)

Installation Option 1 (open enclosure) leaves a complete air outlet opening above the enclosure to provide the

necessary air circulation path for the Dynamic Heat Control™ system. This has been found to be well accepted

with respect to ﬁnal appearance and offer minimal distraction. It also allows for efﬁcient circulation of air within the

room. This option offers the simplest method for framing and installation. Limit the air outlet opening height to 4”

to reduce the risk of items inadvertly falling into the enclosure. The air outlet opening must extend around the

entire perimeter, or the entire front face of the enclosure, where the enclosure runs from wall to wall.

MINIMUM AIR OUTLET OPENING DIMENSIONS

EX36 EX42

(Q x R)* 112 sq. in. minimum (Q must be 2-3”)

L72”

* Grills, grates, louvers, or other covers are only permitted if the free area is equal to or greater than

the required minimum opening size listed above.

Wall mounted

object (picture

frame, appli-

ance, etc.)

ceiling

enclosure top

must be installed

2-3”

0-1.5” Max.

6” min.

Air outlet opening is required to be

centered with the appliance.

ALTERNATIVE

(Q x R)*

DYNAMIC HEAT

CONTROL™ AIR

OUTLET OPEN-

ING IS HOT WHEN

APPLIANCE IS

OPERATING!

Front air outlet opening must

be located out of reach of the

user. Air outlet must not be

restricted by furnishings or

decor.

Installation Option 2 (front opening) requires an air outlet opening to be framed no more than 1.5” below the

enclosure top to avoid trapping heat in the upper areas and the air outlet opening centered on the appliance center.

Minimum air outlet opening dimensions must be followed. Framing the air outlet opening lower will overheat the

appliance, the enclosure, and ﬁnishing material.

2 1/2”

min.

Suitable for Dynamic Heat Control™ Plus

W415-2753 / A / 07.20.20

installation planning

Air outlet opening is required to be centered with the appliance.

(Q x R)* AIR OUTLET

OPENING IS HOT

WHEN APPLIANCE

IS OPERATING!

Room 1

Room 2

Dynamic Heat

Control™ rear air

outlet opening must

be located out of

reach of the user.

Opening must not

be restricted by fur-

nishings or decor.

Installation Option 3 (rear opening) requires an air outlet opening to be framed no more than 1.5” below the

enclosure top to avoid trapping heat in the upper areas and centered on the appliance center. Minimum air outlet

opening dimension must be followed. The opening is required. Framing the rear opening lower will overheat

the appliance, the enclosure, and ﬁnishing material.

Increasing the air outlet opening will allow the appliance, the barrier, the temperatures on the surfaces above the ﬁreplace

opening, and the enclosure be at cooler temperatures. It will also allow the air to circulate more effectively in the room. How-

ever, if the appliance is equipped with the Dynamic Heat Control™ Plus, then the opening size must be 120 sq. in..

note:

2.3 installation option 3 - rear opening

!WARNING

• When using a rear air outlet opening, it is critical that the adjoining room or living spaces are in direct

air communication (i.e. of an open plan conﬁguration or connected by a permanently open doorway

or archway). This prevents the appliance from being in a negative pressure more than that of the ad-

joining room. Failure to follow these requirements can result in reversing the Dynamic Heat Control™

air ﬂow and will cause the appliance, safety barrier, and ﬁnishing materials to overheat, creating a ﬁre

hazard.

Suitable for Dynamic Heat Control™ Plus

W415-2753 / A / 07.20.20 7

installation planning

2.4 installation option 4 - open enclosure with hard combustible valance

ceiling

4” min

air outlet opening

must be continuous

around enclosure top.

6” Max.

6” Min.

ALTERNATIVE

DYNAMIC HEAT

CONTROL™ AIR

OUTLET OPEN-

ING IS HOT WHEN

APPLIANCE IS

OPERATING!

Air outlet opening must be located out of reach of the user.

Air outlet must not be restricted by furnishings or decor.

Wall mounted object

(picture frame, appli-

ance, etc.)

ABSOLUTELY NO OBSTRUCTION OR RESTRICTION AL-

LOWED IN THE ENTIRE SHADED AREA WITH THE EXCEP-

TION OF APPROVED VENTING

Installation Option 4 (open enclosure with hard combustible valance) is similar to Installation Option 1 with the

addition of a hard combustible valance. Minimum opening dimensions and valance dimensions must be followed.

Restricting air movement within the valance area will overheat the appliance, the enclosure, and ﬁnishing

material.

Dynamic Heat Control™ can be installed with both front and rear air outlet openings to allow heat to circulate in two rooms,

however, it is recommended to install the air outlet opening at different heights that meet the installation parameters for aesthetic

purposes. For Dynamic Heat Control™ Plus, a second opening MUST NOT be installed.

note:

NOT suitable for Dynamic Heat Control™ Plus

Air outlet opening must be at least con-

tinuous around the top of the enclosure

for a valance to be permitted. Using

the minimum air outlet opening from

Installation Option 2 and Option 3

is not permitted and will overheat the

appliance.

note:

W415-2753 / A / 07.20.20

installation planning

2.5 installation option 5 - side openings

Suitable for Dynamic Heat Control™ Plus

Installation Option 5 (side openings) requires two (2) air outlet openings to be framed no more than 1.5” below

the enclosure top to avoid trapping heat in the upper areas and the air outlet opening centered on the appliance

center. Minimum air outlet opening dimensions must be followed. Framing the air outlet opening lower will

overheat the appliance, the enclosure, and ﬁnishing material.

MINIMUM AIR OUTLET OPENING DIMENSIONS

EX36 EX42

(Q x R)* 2x 56 sq. in. openings minimum (Q must be 3-4”)

L72”

*Grills, grates, louvers, or other covers are only permitted if the free area is equal to or greater than

the required minimum opening size listed above.

Wall mounted

object (picture

frame, appli-

ance, etc.)

ceiling

enclosure

top must

be installed

0-1.5” Max.

Air outlet openings are required to be

centered with the appliance.

(Q x R)*

DYNAMIC HEAT

CONTROL™ AIR

OUTLET OPEN-

ING IS HOT WHEN

APPLIANCE IS

OPERATING!

Side air outlet openings must

be located out of reach of the

user. Air outlet must not be

restricted by furnishings or

decor.

2 1/2”

min.

ALTERNATIVE

3-4”

6” MIN

W415-2753 / A / 07.20.20 9

installation planning

3.0 appliance overview

side view

top view

(frame and deﬂectors not shown)

For plate removal, see “Dynamic Heat

Control™ installation” section.

deﬂector shown after installation

header

shield

Header shield not illustrated.

W415-2753 / A / 07.20.20

Dynamic Heat Control™ installation

4.0 Dynamic Heat Control™ installation

1. Remove fasteners securing header shield. Do not discard fasteners.

Before starting the Dynamic Heat Control™ installation, remove the barrier. Refer to the appliance installation

manual.

Header

shield

The shipping brackets must only be removed from the header shield if the enclosure is

recessed.

note:

Shipping brackets

2. Once the header shield is removed, replace the 4 screws removed in step 1.

Inhaltsverzeichnis

Andere Napoleon Kaminzubehör Handbücher

Napoleon

Napoleon GPFTS Bedienungsanleitung

Napoleon

Napoleon DBPDX42 Bedienungsanleitung

Napoleon

Napoleon NEFL60B-1 Bedienungsanleitung

Napoleon

Napoleon GI-RB3 Bedienungsanleitung

Napoleon

Napoleon PSL36SS Bedienungsanleitung

Napoleon

Napoleon Allure Vertical Series Bedienungsanleitung

Napoleon

Napoleon Woodland HEFI27H Bedienungsanleitung

Napoleon

Napoleon GDS60-1 Bedienungsanleitung

Napoleon

Napoleon B52NTL Bedienungsanleitung

Napoleon

Napoleon DBPEX36 Bedienungsanleitung

Napoleon

Napoleon FPWI3 Bedienungsanleitung

Napoleon

Napoleon WHD31 Bedienungsanleitung

Napoleon

Napoleon BHD4 PENINSULA Bedienungsanleitung

Napoleon

Napoleon GD862KT Bedienungsanleitung

Napoleon

Napoleon RCHS20 Bedienungsanleitung

Napoleon

Napoleon Ascent DBPX70 Bedienungsanleitung

Napoleon

Napoleon high country nz3000h Bedienungsanleitung

Napoleon

Napoleon MKRY3 Bedienungsanleitung

Napoleon

Napoleon LHD45 Bedienungsanleitung

Napoleon

Napoleon RP6 Bedienungsanleitung

Napoleon

Napoleon GS67-1 Bedienungsanleitung

Napoleon

Napoleon CISM Bedienungsanleitung

Napoleon

Napoleon Oakville Series Bedienungsanleitung

Napoleon

Napoleon PRPH35 Bedienungsanleitung

Beliebte Kaminzubehör Handbücher anderer Marken

Valor

Valor L2 1700K Bedienungsanleitung

Exodraft

Exodraft Xzense Bedienungsanleitung

Whalen

Whalen Ruso MNFP62BF23-6 Bedienungsanleitung

Lopi

Lopi Hearthview 864 Bedienungsanleitung

Woodstock Soapstone

Woodstock Soapstone Fireview 201 Bedienungsanleitung

EdilKamin

EdilKamin SERBATOIO 250 Kurzanleitung

Bronpi

Bronpi KIT-1 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces 22150051 Bedienungsanleitung

Travis Industries

Travis Industries 33 DVI Bedienungsanleitung

Superior

Superior ASD3628-TI Bedienungsanleitung

pleasant hearth

pleasant hearth OFP28WG Bedienungsanleitung

IHP

IHP Astria Series Bedienungsanleitung

Firegear

Firegear FG-H-2110SS Bedienungsanleitung

Nibe

Nibe Contura C i31 Bedienungsanleitung

kozy heat

kozy heat KZK-052 Bedienungsanleitung

SimpliFire

SimpliFire SF-WM36 Bedienungsanleitung

Bluegrass Living

Bluegrass Living BC18NR Kurzanleitung

pleasant hearth

pleasant hearth IRIS SCROLL Bedienungsanleitung