National Instruments CFP-20xx Bedienungsanleitung

Quick Start Guide

FieldPoint cFP-20xx

What You Need to Get Set Up

•cFP-20xx LabVIEW RT controller

• Mounting hardware (DIN rail,

panel-mount, or rack-mount

accessory)

• I/O module(s)

•cFP-BP-xbackplane, connector

blocks, cables

• 11–30 VDC power supply

• Accessories: Ethernet cable,

number 2 Phillips screwdriver

• PC running Windows

• FieldPoint software 3.0.2 or later

•LabVIEWRT

™

cFP-20xx Quick Start Guide 2 ni.com

1. Mount the Compact FieldPoint Backplane

You can mount the cFP-BP-xbackplane on a 35 mm DIN rail, on a panel, or in a

standard 19 in. rack. Before using any of these mounting methods, record the serial

number from the back of the backplane.

Each set of mounting instructions in this document includes an instruction to

connect the protective earth (PE) ground terminal on the cFP-BP-xbackplane to

the system safety ground. The backplane PE ground terminal has the following

symbol stamped beside it: . Connect the backplane PE ground terminal to the

system safety ground using 14 AWG (1.6 mm) wire with a ring lug. Use the

5/16 in. panhead screw shipped with the backplane to secure the ring lug to the

backplane PE ground terminal.

Caution Keep in mind these requirements for space and cabling

clearance:

• Allow at least 51 mm (2 in.) all around the backplane for air

circulation.

• Allow 38 mm (1.5 in.) below and 51 mm (2 in.) above the controller

for cabling clearance.

Cabling

Clearance

4 slots = 246 mm (9.68 in.)

8 slots = 441 mm (17.4 in.)

Cooling Outline

51 mm (2 in.)

Cooling Outline

51 mm (2 in.)

Min. 182 mm (7.18 in.)

106 mm (4.18 in.)

Cabling

Clearance

Cooling Outline

51 mm (2 in.)

All Around

4 slots = 246 mm (9.68 in.)

8 slots = 441 mm (17.4 in.)

127 mm

(5.00 in.)

Min. 165 mm

(6.50 in.)

cFP-20xx Quick Start Guide 4 ni.com

Mounting the Backplane on a Panel

1. Fasten the panel-mount plates to the back of the cFP-BP-xusing a number 2

Phillips screwdriver and the 8-32 × 5/16 in. countersink screws shipped with

the kit.

Caution Do not use screws longer than 5/16 in. to fasten the

panel-mount plates to the backplane.

TIONAL

INSTRUMENTS

102 mm

(4 in.)

457 mm (18 in.)

104.78 mm

(4.1 in.)

63.50 mm

(2.5 in.)

22.23 mm

(0.9 in.)

33.15 mm

(1.3 in.)

129.54 mm

(5.1 in.)

311.40 mm

(12.3 in.)

387.60 mm

(15.3 in.)

407.80 mm

(16.1 in.)

127.00 mm

(5.0 in.)

440.94 mm

(17.4 in.)

260 mm (10.25 in.)

102 mm

(4 in.)

cFP-20xx Quick Start Guide 6 ni.com

2. Bolt or screw the panel-mount accessory to a panel.

3. Connect the PE ground terminal on the cFP-BP-xto safety ground.

Caution Disconnect power before removing the backplane from the

panel.

Mounting the Backplane on a DIN Rail

NI recommends DIN rail mounting for the cFP-BP-4 only. Use panel mounting

or rack mounting for the cFP-BP-8. The DIN rail mounting kit is NI part

number 778614-01.

1. Fasten the DIN rail clip to the cFP-BP-4 using a number 2 Phillips screwdriver

and the 8-32 × 5/16 in. countersink screws shipped with the clip.

104.74 mm

(4.1 in.)

63.46 mm

(2.5 in.)

127.00 mm

(5.0 in.)

22.19 mm

(0.9 in.)

34.04 mm

(1.3 in.)

84.84 mm

(3.3 in.)

161.04 mm

(6.3 in.)

211.84 mm

(8.3 in.)

245.87 mm

(9.6 in.)

Caution Do not use screws longer than 5/16 in. to fasten the DIN rail

clip to the backplane.

2. Insert one edge of the DIN rail into the deeper opening of the DIN rail clip.

3. Press down firmly on the backplane to compress the spring until the clip locks

in place on the DIN rail.

4. Connect the PE ground terminal on the cFP-BP-4 to safety ground.

Caution Disconnect power before removing the backplane from the

DIN rail.

TIONAL

INSTRUMENTS

cFP-20xx Quick Start Guide 8 ni.com

Mounting the Backplane in a Standard 19-in. Rack

1. Fasten the rack-mount bracket to the back of the cFP-BP-xusing the captive

screws on the bracket.

2. Bolt the rack-mount accessory to a standard 19-in. rack.

TIONAL

INSTRUMENTS

3. Connect the PE ground terminal on the cFP-BP-xto safety ground.

Caution Disconnect power before removing the backplane from the

bracket.

TIONAL

INSTRUMENTS

cFP-20xx Quick Start Guide 10 ni.com

2. Install the cFP-20xx Controller on the Backplane

1. Make sure that no power is connected to the controller.

2. Make sure that the cFP-20xx controller is right side up with the NI logo at

the top, and align the captive screws on the controller with the holes on the

backplane.

3. Seat the card edge at the back of the controller in the card-edge connector on

the backplane.

4. Press the controller firmly to seat it on the backplane.

5. Using a number 2 Phillips screwdriver with a shank of at least 64 mm (2.5 in.)

length, tighten the captive screws to 1.1 N · m (10 lb · in.) of torque.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere National Instruments Computerhardware Handbücher

National Instruments

National Instruments PCI-6110E/6111E Bedienungsanleitung

National Instruments

National Instruments NI roboRIO Bedienungsanleitung

National Instruments

National Instruments NI PXIe-1082 Bedienungsanleitung

National Instruments

National Instruments PXIe-7911 Bedienungsanleitung

National Instruments

National Instruments PXIe-8240 Bedienungsanleitung

National Instruments

National Instruments PCI-6601 Bedienungsanleitung

National Instruments

National Instruments NI 9213 Bedienungsanleitung

National Instruments

National Instruments NI 783 R Series Bedienungsanleitung

National Instruments

National Instruments PXIe-4468 Handbuch

National Instruments

National Instruments NI 6703 Handbuch

National Instruments

National Instruments USB-7856 Bedienungsanleitung

National Instruments

National Instruments PCI-6034E Bedienungsanleitung

National Instruments

National Instruments PC-LPM-16/PnP Bedienungsanleitung

National Instruments

National Instruments PC/104-GPIB Bedienungsanleitung

National Instruments

National Instruments NI PXIe-1085 Bedienungsanleitung

National Instruments

National Instruments NI PXI-8221 Bedienungsanleitung

National Instruments

National Instruments Network Adapter NI PXIe-1075 Bedienungsanleitung

National Instruments

National Instruments Compact FieldPoint Mounting Accessories... Bedienungsanleitung

National Instruments

National Instruments PXI-8170 Series Bedienungsanleitung

National Instruments

National Instruments DAQ PCI E Series Bedienungsanleitung

National Instruments

National Instruments PCI-6035E Bedienungsanleitung

National Instruments

National Instruments PCI-7041 Bedienungsanleitung

National Instruments

National Instruments Multifunction RIO NI R Series Bedienungsanleitung

National Instruments

National Instruments MXI-2 Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

Advantech

Advantech ASMB-935 Series Bedienungsanleitung

National Instruments cFP-20xx Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken