National Instruments Compact FieldPoint Mounting Accessories... Bedienungsanleitung

Quick Start Guide

FieldPoint cFP-21xx

What You Need to Get Set Up

•cFP-21xx LabVIEW RT controller

• Mounting hardware (DIN rail,

panel-mount, or rack-mount

accessory)

• I/O module(s)

•cFP-BP-xbackplane, connector

blocks, cables

• 11–30 VDC power supply

• Accessories: Ethernet cable,

number 2 Phillips screwdriver

• PC running Windows

• FieldPoint software 4.1.1 or later

• LabVIEW Real-Time Module

™

cFP-21xx Quick Start Guide 2 ni.com

1. Mount the Compact FieldPoint Backplane

You can mount the cFP-BP-xbackplane on a 35mm DIN rail, on a panel, or in a

standard 19 in. rack. Before using any of these mounting methods, record the serial

number from the back of the backplane.

Each set of mounting instructions in this document includes an instruction to

connect the protective earth (PE) ground terminal on the cFP-BP-xbackplane to

the system safety ground. The backplane PE ground terminal has the following

symbol stamped beside it: . Connect the backplane PE ground terminal to the

system safety ground using 14 AWG (1.6 mm) wire with a ring lug. Use the

5/16 in. panhead screw shipped with the backplane to secure the ring lug to the

backplane PE ground terminal.

Caution Keep in mind these requirements for space and cabling

clearance:

• Allow at least 51 mm (2 in.) all around the backplane for air

circulation.

• Allow 38 mm (1.5 in.) below and 51 mm (2 in.) above the controller.

Caution If you are using UL Recognized I\O modules with the Compact

FieldPoint system, you must install the entire system in a suitably rated,

UL Listed NEMA or IP enclosure.

Cabling Clearance Cooling Outline 51 mm (2 in.) All Around

4 slots = 246 mm (9.68 in.)

8 slots = 441 mm (17.4 in.)

127 mm

(5.00 in.)

Min. 165 mm

(6.50 in.)

Cabling

Clearance

4 slots = 246 mm (9.68 in.)

8 slots = 441 mm (17.4 in.)

Cooling Outline 51 mm (2 in.) Cooling Outline 51 mm (2 in.)

Min. 182 mm (7.18 in.)

106 mm (4.18 in.)

cFP-21xx Quick Start Guide 4 ni.com

Caution NI recommends that you use one of the mounting systems

described in this document. If you decide to use a custom mounting

solution, make sure that the screws you use are short enough to fit in the

holes in the backplane. The screw holes are 5 mm (0.2 in.) deep.

Mounting the Backplane on a Panel

1. Fasten the panel-mount plates to the back of the cFP-BP-xusing a

number 2 Phillips screwdriver and the 8-32 ×5/16 in. countersink screws

shipped with the kit.

Caution Do not use screws longer than 5/16 in. to fasten the

panel-mount plates to the backplane.

NATIONAL

INSTRUMENTS

102 mm

(4 in.)

457 mm (18 in.)

cFP-21xx Quick Start Guide 6 ni.com

104.78 mm

(4.1 in.)

63.50 mm

(2.5 in.)

22.23 mm

(0.9 in.)

33.15 mm

(1.3 in.)

129.54 mm

(5.1 in.)

311.40 mm

(12.3 in.)

387.60 mm

(15.3 in.)

407.80 mm

(16.1 in.)

127.00 mm

(5.0 in.)

440.94 mm

(17.4 in.)

260 mm (10.25 in.)

102 mm

(4 in.)

2. Bolt or screw the panel-mount accessory to a panel.

3. Connect the PE ground terminal on the cFP-BP-xto safety ground.

Caution Disconnect power before removing the backplane from the

panel.

Mounting the Backplane on a DIN Rail

NI recommends DIN rail mounting for the cFP-BP-4 only. Use panel mounting or

rack mounting for the cFP-BP-8. The DIN rail mounting kit is NI part number

778614-01.

1. Fasten the DIN rail clip to the cFP-BP-4 using a number 2 Phillips screwdriver

and the 8-32 ×5/16 in. countersink screws shipped with the clip.

104.74 mm

(4.1 in.)

63.46 mm

(2.5 in.)

127.00 mm

(5.0 in.)

22.19 mm

(0.9 in.)

34.04 mm

(1.3 in.)

84.84 mm

(3.3 in.)

161.04 mm

(6.3 in.)

211.84 mm

(8.3 in.)

245.87 mm

(9.6 in.)

cFP-21xx Quick Start Guide 8 ni.com

Caution Do not use screws longer than 5/16 in. to fasten the DIN rail

clip to the backplane.

2. Insert one edge of the DIN rail into the deeper opening of the DIN rail clip.

3. Press down firmly on the backplane to compress the spring until the clip locks

in place on the DIN rail.

4. Connect the PE ground terminal on the cFP-BP-4 to safety ground.

Caution Disconnect power before removing the backplane from the

DIN rail.

NATIONAL

INSTRUMENTS

Mounting the Backplane in a Standard 19 in. Rack

1. Fasten the rack-mount bracket to the back of the cFP-BP-xusing the captive

screws on the bracket.

2. Bolt the rack-mount accessory to a standard 19 in. rack.

NATIONAL

INSTRUMENTS

cFP-21xx Quick Start Guide 10 ni.com

3. Connect the PE ground terminal on the cFP-BP-xto safety ground.

Caution Disconnect power before removing the backplane from the

DIN rail.

NATIONAL

INSTRUMENTS

Inhaltsverzeichnis

Andere National Instruments Computerhardware Handbücher

National Instruments

National Instruments PXI-8187 Bedienungsanleitung

National Instruments

National Instruments PXI-8101 Bedienungsanleitung

National Instruments

National Instruments GPIB-ENET-1000 Bedienungsanleitung

National Instruments

National Instruments AT-GPIB/TNT Bedienungsanleitung

National Instruments

National Instruments PCI-6110E/6111E Bedienungsanleitung

National Instruments

National Instruments GPIB Series Bedienungsanleitung

National Instruments

National Instruments PXI NI 8171 Series Bedienungsanleitung

National Instruments

National Instruments PCMCIA-GPIB Bedienungsanleitung

National Instruments

National Instruments NI Real-Time Hypervisor Bedienungsanleitung

National Instruments

National Instruments PCI-6528 Bedienungsanleitung

National Instruments

National Instruments VME-PCI8022 Bedienungsanleitung

National Instruments

National Instruments AT-GPIB Bedienungsanleitung

National Instruments

National Instruments NI 5401 Bedienungsanleitung

National Instruments

National Instruments PCMCIA-FBUS/2 Bedienungsanleitung

National Instruments

National Instruments GPIB-1014 Series Bedienungsanleitung

National Instruments

National Instruments Texas Instruments 6711 DSK Bedienungsanleitung

National Instruments

National Instruments PCI-1407 Bedienungsanleitung

National Instruments

National Instruments SET-2090 Stücklistenhandbuch

National Instruments

National Instruments PCMCIA Serias Bedienungsanleitung

National Instruments

National Instruments GPIB-PCII Bedienungsanleitung

National Instruments

National Instruments NI-9252 Handbuch

National Instruments

National Instruments PCMCIA-232 Bedienungsanleitung

National Instruments

National Instruments GPIB-PC Bedienungsanleitung

National Instruments

National Instruments AT-MIO/AI E Series Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

Advantech

Advantech ASMB-935 Series Bedienungsanleitung