National Instruments GPIB-120B Bedienungsanleitung

GPIB-120B

INSTALLATION GUIDE AND SPECIFICATIONS

GPIB Hardware

Contents

Electromagnetic Compatibility Guidelines .............................................................................. 1

GPIB-USB Interfaces ............................................................................................................... 2

LED Signaling ..................................................................................................................4

PCIe-GPIB, PCIe-GPIB+, PCI-GPIB, PCI-GPIB+, PCI-GPIB/LP, and PCI-8232................. 5

ExpressCard-GPIB ................................................................................................................... 7

PMC-GPIB ............................................................................................................................... 8

PXI-GPIB and PXI-8232..........................................................................................................10

GPIB-ENET/1000 .................................................................................................................... 12

GPIB-ENET/1000 Installation ......................................................................................... 12

Baseplate Identification Label .......................................................................................... 13

Startup............................................................................................................................... 13

Ethernet Connector LEDs................................................................................................. 14

Software Recognition ....................................................................................................... 14

Ethernet Configuration ..................................................................................................... 15

Firmware Update .............................................................................................................. 17

READY LED Signaling ................................................................................................... 17

CFG RESET Switch ......................................................................................................... 18

Specifications............................................................................................................................ 19

ExpressCard-GPIB ........................................................................................................... 19

GPIB-ENET/1000 ............................................................................................................ 20

GPIB-USB-HS.................................................................................................................. 21

GPIB-USB-HS+ ............................................................................................................... 22

PCI-8232........................................................................................................................... 23

PCIe-GPIB and PCIe-GPIB+ ........................................................................................... 25

PCI-GPIB.......................................................................................................................... 26

PCI-GPIB+ ....................................................................................................................... 27

PMC-GPIB .......................................................................................................................28

PXI-8232 .......................................................................................................................... 29

PXI-GPIB ......................................................................................................................... 30

All Devices ....................................................................................................................... 32

Worldwide Support and Services ............................................................................................. 34

Electromagnetic Compatibility Guidelines

This hardware has been tested and found to comply with the applicable regulatory requirements

and limits for electromagnetic compatibility (EMC) as indicated in the hardware’s Declaration

of Conformity (DoC)1. These requirements and limits are designed to provide reasonable

2|ni.com |GPIB Hardware Installation Guide and Specifications

protection against harmful interference when the hardware is operated in the intended

electromagnetic environment. In special cases, for example when either highly sensitive or noisy

hardware is being used in close proximity, additional mitigation measures may have to be

employed to minimize the potential for electromagnetic interference.

While this hardware is compliant with the applicable regulatory EMC requirements, there is no

guarantee that interference will not occur in a particular installation. To minimize the potential

for the hardware to cause interference to radio and television reception or to experience

unacceptable performance degradation, install and use this hardware in strict accordance with

the instructions in the hardware documentation and the DoC1.

If this hardware does cause interference with licensed radio communications services or other

nearby electronics, which can be determined by turning the hardware off and on, you are

encouraged to try to correct the interference by one or more of the following measures:

• Reorient the antenna of the receiver (the device suffering interference).

• Relocate the transmitter (the device generating interference) with respect to the receiver.

• Plug the transmitter into a different outlet so that the transmitter and the receiver are on

different branch circuits.

Some hardware may require the use of a metal, shielded enclosure (windowless version) to meet

the EMC requirements for special EMC environments such as, for marine use or in heavy

industrial areas. Refer to the hardware’s user documentation and the DoC1 for product

installation requirements.

When the hardware is connected to a test object or to test leads, the system may become more

sensitive to disturbances or may cause interference in the local electromagnetic environment.

Operation of this hardware in a residential area is likely to cause harmful interference. Users are

required to correct the interference at their own expense or cease operation of the hardware.

Changes or modifications not expressly approved by National Instruments could void the user’s

right to operate the hardware under the local regulatory rules.

GPIB-USB Interfaces

Caution Ground loops create an electric shock hazard and can cause damage to

your GPIB-USB hardware, your computer, and other system components. A ground

loop can occur when your computer and one or more connected instruments do not

share the same ground potential.

1 The Declaration of Conformity (DoC) contains important EMC compliance information and instructions

for the user or installer. To obtain the DoC for this product, visit ni.com/certification, search by

model number or product line, and click the appropriate link in the Certification column.

GPIB Hardware Installation Guide and Specifications |© National Instruments |3

To prevent damage to your GPIB-USB hardware and other system components, do

any of the following:

• Ensure that your system and all instruments connected to it share the same ground

potential. This eliminates the possibility of voltage differential running through

your system.

• Use a GPIB-120B Bus Isolator/Expander to isolate GPIB systems and expand the

GPIB interface up to 28 devices.

• Use a pair of GPIB-140A High-Speed Fiber-Optic Bus Extenders. This

transforms the GPIB signals at each end into fiber optic signals, allowing each

unit to reside at a different ground potential.

• Use an isolated USB hub.

Complete the following steps to install your interface:

1. Connect the USB connector from the GPIB-USB interface to an available USB Type A port

on your computer.

2. Before connecting the GPIB-USB interface to GPIB devices, ensure that the computer and

the GPIB devices are at the same ground potential. The GPIB-USB interface connects

directly to most GPIB devices without requiring a GPIB cable.

3. If your computer is already running, the operating system automatically detects the GPIB

interface. Otherwise, the GPIB interface is detected when you start your computer.

Figure 1. Installing the GPIB-USB Interface

The GPIB hardware installation is now complete.

1 Computer 2 USB Connector 3 GPIB-USB Interface 4 To GPIB Devices

4|ni.com |GPIB Hardware Installation Guide and Specifications

LED Signaling

The GPIB-USB-HS controller uses two LEDs to indicate status and activity.

When you connect the GPIB-USB-HS controller, the READY LED lights either green or amber

once the driver is installed and detected. Table 1 summarizes the functionality of the LEDs on

the GPIB-USB-HS hardware.

The GPIB-USB-HS+ controller uses a multicolored LED to indicate status and activity. Table 2

summarizes the functionality of the LEDs on the GPIB-USB-HS+ hardware.

Table 1. GPIB-USB-HS LED Descriptions

LED Description

READY Green indicates that the GPIB-USB-HS is plugged into a USB full-speed

(USB 1.1) port.

Amber indicates that the GPIB-USB-HS is plugged into a USB Hi-Speed

(USB 2.0) port.

ACTIVE Indicates activity on the GPIB bus.

Table 2. GPIB-USB-HS+ LED Descriptions

LED Description

Alternating

Amber/Green

The GPIB-USB-HS+ is not ready to use. You must install (or re-install)

the NI-488.2 driver before using the GPIB-USB-HS+.

Note: Windows 8 and later suspend power to a USB device that does not

have a driver attached. If the LED does not light, try reinstalling the

NI-488.2 driver.

Steady Green Indicates that the GPIB-USB-HS+ is plugged into a USB full-speed

(USB 1.1) port.

Steady Amber Indicates that the GPIB-USB-HS+ is plugged into a USB Hi-Speed

(USB 2.0) port.

Blinking Amber

or Green

Indicates activity on the GPIB bus or that the GPIB Analyzer is

capturing.

GPIB Hardware Installation Guide and Specifications |© National Instruments |5

PCIe-GPIB, PCIe-GPIB+, PCI-GPIB,

PCI-GPIB+, PCI-GPIB/LP, and PCI-8232

Caution Electrostatic discharge can damage several components on your GPIB

board. To avoid such damage in handling your board, touch the antistatic plastic

package to a metal part of your computer chassis before removing the board from the

package.

Complete the following steps to install your interface:

1. Make sure that your computer is powered off. Keep the computer plugged in so that it

remains grounded while you install the GPIB hardware.

2. Remove the top cover (or other access panels) to gain access to the computer expansion

slots.

3. Find an unused expansion slot in your computer. Your PCI board can be plugged into either

a 3.3 V or 5 V, 32- or 64-bit PCI slot. Your PCI Express card can be plugged into a x1, x4,

x8, or x16 PCI Express slot.

4. Remove the corresponding slot cover on the back panel of the computer.

5. Insert the GPIB board into the slot with the GPIB connector sticking out of the opening on

the back panel, as shown in Figure 2. It might be a tight fit, but do not force the board into

place.

Note Your PCI Express board may be larger than the one shown in the figure.

6|ni.com |GPIB Hardware Installation Guide and Specifications

Figure 2. Installing Your PCI/PCI Express Board

6. Screw the mounting bracket of the GPIB board to the back panel rail of the computer.

7. Replace the top cover (or the access panel to the expansion slot).

8. Power on your computer.

The GPIB hardware installation is now complete.

1 PCI Express Board

2 PCI Express Slot

3 Computer 1PCIBoard

2PCISlot

3 Computer

GPIB Hardware Installation Guide and Specifications |© National Instruments |7

ExpressCard-GPIB

Caution Ground loops create an electric shock hazard and can cause damage to

your ExpressCard-GPIB hardware, your computer, and other system components. A

ground loop can occur when your computer and one or more connected instruments

do not share the same ground potential.

To prevent damage to your ExpressCard-GPIB hardware and other system

components, do any of the following:

• Ensure that your system and all instruments connected to it share the same ground

potential. This eliminates the possibility of voltage differential running through

your system.

• Use a GPIB-120B Bus Isolator/Expander to isolate GPIB systems and expand the

GPIB interface up to 28 devices.

• Use a pair of GPIB-140A High-Speed Fiber-Optic Bus Extenders. This

transforms the GPIB signals at each end into fiber optic signals, allowing each

unit to reside at a different ground potential.

Complete the following steps to install the ExpressCard-GPIB interface:

1. Plug the card into an available ExpressCard™ slot on your computer.

2. Before connecting the ExpressCard-GPIB interface to GPIB devices, ensure that the

computer and the GPIB devices are at the same ground potential.

3. If your computer is already running, the operating system automatically detects the GPIB

interface. Otherwise, the GPIB interface is detected when you start your computer.

8|ni.com |GPIB Hardware Installation Guide and Specifications

Figure 3 shows how to insert the ExpressCard-GPIB and connect the cable.

Figure 3. Inserting the ExpressCard-GPIB

The GPIB hardware installation is now complete.

PMC-GPIB

Caution Electrostatic discharge can damage several components on your GPIB

board. To avoid electrostatic damage when you handle the board, touch the antistatic

plastic package to a metal part of your system chassis before removing the board from

the package.

Complete the following steps to install your PMC-GPIB:

1. Power off your system.

2. Find an unused PMC slot in your system. You may need to remove the host from the system

to access the PMC slot.

3. Remove the corresponding slot filler panel from the host.

1 Notebook Computer 2 ExpressCard Slot 3 ExpressCard-GPIB Cable

GPIB Hardware Installation Guide and Specifications |© National Instruments |9

4. Insert the PMC-GPIB into the slot as shown in Figure 4. It might be a tight fit, but do not

force the board into place.

Figure 4. Installing the PMC-GPIB

5. Use the mounting hardware provided to fasten the PMC-GPIB to the host.

6. Reinstall the host, if you removed it to install the PMC-GPIB.

7. Power on your system.

The PMC-GPIB hardware installation is now complete.

1 Host Face Plate

2 3.3 V Keying Hole

3 5 V Keying Hole

4 PMC-GPIB Board

5 Mounting Screws

Andere Handbücher für GPIB-120B

Inhaltsverzeichnis

Andere National Instruments Computerhardware Handbücher

National Instruments

National Instruments PCI-8430 Bedienungsanleitung

National Instruments

National Instruments NI PXIe-8130 Bedienungsanleitung

National Instruments

National Instruments PXIe-8822 Bedienungsanleitung

National Instruments

National Instruments NI 6521 Bedienungsanleitung

National Instruments

National Instruments USB-6501 Bedienungsanleitung

National Instruments

National Instruments USB-6211 OEM Bedienungsanleitung

National Instruments

National Instruments PCI-6110E/6111E Bedienungsanleitung

National Instruments

National Instruments PMC-GPIB Bedienungsanleitung

National Instruments

National Instruments NI 9263 Bedienungsanleitung

National Instruments

National Instruments PXI-8106 Bedienungsanleitung

National Instruments

National Instruments PCI-6601 Bedienungsanleitung

National Instruments

National Instruments GPIB Series Bedienungsanleitung

National Instruments

National Instruments NI 9213 Bedienungsanleitung

National Instruments

National Instruments NI PXIe-8105 Bedienungsanleitung

National Instruments

National Instruments GPIB-PCII Bedienungsanleitung

National Instruments

National Instruments NI 783 R Series Bedienungsanleitung

National Instruments

National Instruments DAQPad-6020E Bedienungsanleitung

National Instruments

National Instruments NI sbRIO-960x Bedienungsanleitung

National Instruments

National Instruments Two-Slot Embedded Controller NI PXI-8183 Bedienungsanleitung

National Instruments

National Instruments NI 9401 Bedienungsanleitung

National Instruments

National Instruments PXIe-5832 Bedienungsanleitung

National Instruments

National Instruments NI PXIe-1062Q Bedienungsanleitung

National Instruments

National Instruments MXI-2 Bedienungsanleitung

National Instruments

National Instruments PCMCIA-FBUS/2 Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

Intel

Intel NUC 12 Pro Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

Advantech

Advantech ASMB-935 Series Bedienungsanleitung

Jupiter

Jupiter RAM PACK Bedienungsanleitung

Measurement Computing

Measurement Computing CIO-EXP-RTD16 Bedienungsanleitung