National Instruments NI 9219 Bedienungsanleitung

NI-9219 Getting

Started

2022-07-06

Contents

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Safety Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Safety Guidelines for Hazardous Voltages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

NI-9219 Safety Voltages (Black Connector). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Safety Guidelines for Hazardous Locations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Electromagnetic Compatibility Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Special Conditions for Marine Applications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Preparing the Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

NI 9219 Pinout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Measurement Types. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Voltage Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Current Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Thermocouple Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

4-Wire Resistance and 4-Wire RTD Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3-Wire RTD Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Full-Bridge Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Half-Bridge Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Digital In Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Open Contact Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

TEDS Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

NI-9219 Connection Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Connecting to a Spring-Terminal Connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

High-Vibration Application Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Excitation Protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Measurement Type Pinout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Voltage Pinout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Current Pinout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Thermocouple Pinout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4-Wire Resistance and 4-Wire RTD Pinout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

3-Wire RTD Pinout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Full-Bridge Pinout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Half-Bridge Pinout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Digital In Pinout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

ni.com

NI-9219 Getting Started

Open Contact Pinout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Where to Go Next. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

NI Services. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

NI-9219 Getting Started

Overview

This document explains how to connect to the NI-9219.

Note Before you begin, read the NI-9219 Safety, Environmental, and

Regulatory Information document on ni.com/manuals and complete the

soware and hardware installation procedures in your chassis

documentation.

Note The guidelines in this document are specific to the NI-9219. The

other components in the system might not meet the same safety ratings.

Refer to the documentation for each component in the system to

determine the safety and EMC ratings for the entire system.

Safety Guidelines

Caution Observe all instructions and cautions in the user documentation.

Using the product in a manner not specified can damage the product and

compromise the built-in safety protection.

Attention Suivez toutes les instructions et respectez toutes les mises

en garde de la documentation d'utilisation. L'utilisation du produit de

toute autre façon que celle spécifiée risque de l'endommager et de

compromettre la protection de sécurité intégrée.

Safety Guidelines for Hazardous Voltages

If hazardous voltages are connected to the product, take the following precautions.

A hazardous voltage is a voltage greater than:

■ 30 V RMS, 42.4 V peak, or 60 V DC in DRY LOCATIONS

■ 16 V RMS, 22.6 V peak, or 35 V DC in WET LOCATIONS

ni.com

NI-9219 Getting Started

Caution Ensure that hazardous voltage wiring is performed only by

qualified personnel adhering to local electrical standards.

Attention S'assurer que le câblage à tension dangereuse est eectué par

du personnel qualifié respectant les normes électriques locales.

Caution Do not mix hazardous voltage circuits and human-accessible

circuits on the same product.

Attention Ne pas combiner des circuits avec des tensions dangereuses et

des circuits accessibles aux personnes sur le même produit.

Caution When product terminals are hazardous voltage LIVE, you must

ensure that devices and circuits connected to the product are properly

insulated from human contact.

Attention Lorsqu'une haute tension dangereuse est appliquée aux

bornes du produit, vous devez vous assurer que les appareils et les circuits

auxquels il est connecté sont correctement isolés de tout contact humain.

Caution You must use the connector backshell kit to ensure that the

terminals are not accessible.

NI-9219 Safety Voltages (Black Connector)

Connect only voltages that are within the following limits.

Channel-to-channel

NI-9219 Getting Started

Continuous 250 V AC, Measurement Category II

Withstand 1,390 V AC, verified by a 5 s dielectric withstand test

Channel-to-earth ground

Continuous 250 V AC, Measurement Category II

Withstand 2,300 V AC, verified by a 5 s dielectric withstand test

Zone 2 hazardous locations applications in Europe

Channel-to-channel and channel-to-earth ground 60 V DC, Measurement Category I

Safety Guidelines for Hazardous Locations

The NI-9219 is suitable for use in hazardous locations; , and hazardous locations;

and nonhazardous locations only. Follow these guidelines if you are installing the

NI-9219 in a potentially explosive environment. Not following these guidelines may

result in serious injury or death.

Caution Do not disconnect I/O-side wires or connectors unless power has

been switched o or the area is known to be nonhazardous.

Caution Do not remove modules unless power has been switched o or

the area is known to be nonhazardous.

Caution Substitution of components may impair suitability for Class I,

Division 2, or Zone 2.

Caution The system must be installed in an enclosure certified for the

intended hazardous (classified) location, having a tool secured cover/door,

where a minimum protection of at least IP54 is provided.

ni.com

NI-9219 Getting Started

Special Conditions for Hazardous Locations Use in Europe and

Internationally

The NI-9219 has been evaluated as equipment under DEMKO ATEX and is IECEx

certified. Each NI-9219 is marked and is suitable for use in Zone 2 hazardous

locations, in ambient temperatures of -40 °C ≤ Ta ≤ 70 °C. If you are using the NI-9219

in Gas Group IIC hazardous locations, you must use the device in an NI chassis that

has been evaluated as Ex nC IIC T4, Ex IIC T4, Ex nA IIC T4, or Ex nL IIC T4 equipment.

Caution Transient protection shall be provided that is set at a level not

exceeding 140% of the peak rated voltage value of 85 V at the supply

terminals to the equipment.

Caution The system shall only be used in an area of not more than

Pollution Degree 2, as defined in IEC/EN 60664-1.

Caution The system shall be mounted in an ATEX/IECEx-certified

enclosure with a minimum ingress protection rating of at least IP54 as

defined in IEC/EN 60079-15.

Caution The enclosure must have a door or cover accessible only by the

use of a tool.

Electromagnetic Compatibility Guidelines

This product was tested and complies with the regulatory requirements and limits

for electromagnetic compatibility (EMC) stated in the product specifications. These

requirements and limits provide reasonable protection against harmful interference

when the product is operated in the intended operational electromagnetic

environment.

This product is intended for use in industrial locations. However, harmful

interference may occur in some installations, when the product is connected to a

peripheral device or test object, or if the product is used in residential or

commercial areas. To minimize interference with radio and television reception and

NI-9219 Getting Started

prevent unacceptable performance degradation, install and use this product in strict

accordance with the instructions in the product documentation.

Furthermore, any changes or modifications to the product not expressly approved

by National Instruments could void your authority to operate it under your local

regulatory rules.

Special Conditions for Marine Applications

Some products are approved for marine (shipboard) applications. To verify marine

approval certification for a product, visit ni.com/product-certifications, search by

model number, and click the appropriate link.

Notice In order to meet the EMC requirements for marine applications,

install the product in a shielded enclosure with shielded and/or filtered

power and input/output ports. In addition, take precautions when

designing, selecting, and installing measurement probes and cables to

ensure that the desired EMC performance is attained.

Preparing the Environment

Ensure that the environment in which you are using the NI-9219 meets the following

specifications.

Operating temperature (IEC 60068-2-1, IEC 60068-2-2) -40 °C to 70 °C

Operating humidity (IEC 60068-2-78) 10% RH to 90% RH, noncondensing

Pollution Degree 2

Maximum altitude 2,000 m

Indoor use only.

Note Refer to the device datasheet on ni.com/manuals for complete

specifications.

ni.com

NI-9219 Getting Started

NI 9219 Pinout

CH0

CH1

CH2

CH3

Mode Pin

1 2 3 4 5 6

Voltage T+ T- — HI LO —

Current T+ T- HI — LO —

4-Wire Resistance T+ T- EX+ HI EX- LO

2-Wire Resistance T+ T- HI — LO —

Thermocouple T+ T- — HI LO —

4-Wire RTD T+ T- EX+ HI EX- LO

3-Wire RTD T+ T- EX+ — EX- LO

Quarter-Bridge T+ T- HI — LO —

Half-Bridge T+ T- EX+ HI EX- —

Full-Bridge T+ T- EX+ HI EX- LO

DI T+ T- — HI LO —

Open Contact T+ T- HI — LO —

Table 1. Signals by Mode

Signal Description

EX+ Positive sensor excitation connection

NI-9219 Getting Started

Signal Description

EX- Negative sensor excitation connection

HI Positive input signal connection

LO Negative input signal connection

T+ TEDS data connection

T- TEDS COM connection

Table 2. Signal Descriptions

Measurement Types

The NI-9219 provides modes for the following measurement types.

■Voltage

■Current

■4-Wire Resistance

■2-Wire Resistance

■Thermocouple

■4-Wire RTD

■3-Wire RTD

■Quarter-Bridge

■Half-Bridge

■Full-Bridge

■Digital In[1]

■Open Contact[1]

1 Only supported in CompactRIO systems.

Voltage Connections

NI 9219

–

ni.com

NI-9219 Getting Started

Andere Handbücher für NI 9219

Inhaltsverzeichnis

Andere National Instruments Computerhardware Handbücher

National Instruments

National Instruments PXIe-8115 Bedienungsanleitung

National Instruments

National Instruments MXI-2 Bedienungsanleitung

National Instruments

National Instruments PMC-GPIB Bedienungsanleitung

National Instruments

National Instruments NI 9213 Bedienungsanleitung

National Instruments

National Instruments NI roboRIO Bedienungsanleitung

National Instruments

National Instruments PXI Express PXIe-1085 Series Bedienungsanleitung

National Instruments

National Instruments NI PXIe-8130 Bedienungsanleitung

National Instruments

National Instruments USB-6501 Bedienungsanleitung

National Instruments

National Instruments PC-DIO-24/PnP Bedienungsanleitung

National Instruments

National Instruments GPIB-1014 Series Bedienungsanleitung

National Instruments

National Instruments PXIe-8100 Bedienungsanleitung

National Instruments

National Instruments NAT7210 Bedienungsanleitung

National Instruments

National Instruments NI PXIe-8130 Bedienungsanleitung

National Instruments

National Instruments AT-GPIB/TNT Bedienungsanleitung

National Instruments

National Instruments 8330 Series Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

National Instruments

National Instruments NI 783 R Series Bedienungsanleitung

National Instruments

National Instruments NI PXIe-8133 Bedienungsanleitung

National Instruments

National Instruments NI 9472 Bedienungsanleitung

National Instruments

National Instruments NI sbRIO-960x Bedienungsanleitung

National Instruments

National Instruments PXIe-5832 Bedienungsanleitung

National Instruments

National Instruments PCI-6601 Bedienungsanleitung

National Instruments

National Instruments Compact FieldPoint Mounting Accessories... Bedienungsanleitung

National Instruments

National Instruments NI 8234 Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

Advantech

Advantech ASMB-935 Series Bedienungsanleitung