National Instruments NI 9514 Bedienungsanleitung

NI-9514

OPERATING INSTRUCTIONS AND

SPECIFICATIONS

NI 9514

Servo Drive Interface Module withFeedback

ni.com/manuals

DeutschFrançais

2|ni.com |NI 9514Operating Instructions and Specifications

This document describes how to use the National Instruments 9514

module and includes specifications and pin assignments for the

NI 9514.

Note The safety guidelines and specifications in this

document are specific to the NI 9514. The other

components in the system may not meet the same safety

ratings and specifications. Refer to the documentation for

each component in the system to determine the safety

ratings and specifications for the entire system.

Related Information

Safety Guidelines

Operate the NI 9501 only as described in these operating

instructions.

NI 9514 Operating Instructions and Specifications |© National Instruments |3

Safety Guidelines for Hazardous Locations

The NI 9514 is suitable for use in Class I, Division 2, Groups A, B,

C, D, T4 hazardous locations; Class I, Zone 2, AEx nA IIC T4 and

Ex nA IIC T4 hazardous locations; and nonhazardous locations

only. Follow these guidelines if you are installing the NI 9514 in a

potentially explosive environment. Not following these guidelines

may result in serious injury or death.

Caution Do not disconnect I/O-side wires or connectors

unless power has been switched off or the area is known to

be nonhazardous.

Caution Do not remove modules unless power has been

switched off or the area is known to be nonhazardous.

Caution Substitution of components may impair

suitability for Class I, Division 2.

Caution For Division 2 and Zone 2 applications, install

the system in an enclosure rated to at least IP 54 as defined

by IEC/EN 60079-15.

4|ni.com |NI 9514Operating Instructions and Specifications

Caution For Division 2 and Zone 2 applications, install a

protection device between the input signal and the Vsup

pin. The device must prevent the Vsup-to-channel voltage

from exceeding 42 V if there is a transient overvoltage

condition.

Special Conditions for Hazardous Locations Use in

Europe and Internationally

This equipment has been evaluated as Ex nA IIC T4 Gc equipment

under DEMKO Certificate No. 07 ATEX 0626664X and is IECEx

UL 14.0089X certified. Each module is marked II 3G and is

suitable for use in Zone 2 hazardous locations, in ambient

temperatures of – 40 °C Ta 70 °C. If you are using the NI 9514

in Gas Group IIC hazardous locations, you must use the device in

an NI chassis that has been evaluated as Ex nC IIC T4, Ex IIC T4,

Ex nA IIC T4, or Ex nL IIC T4 equipment.

Caution You must make sure that transient disturbances

do not exceed 140% of the rated voltage.

Caution The system shall only be used in an area of not

more than Pollution Degree 2, as defined in IEC 60664-1.

NI 9514 Operating Instructions and Specifications |© National Instruments |5

Caution The system shall be mounted in an

ATEX/IECEx-certified enclosure with a minimum ingress

protection rating of at least IP54 as defined in

IEC/EN 60079-15.

Caution The enclosure must have a door or cover

accessible only by the use of a tool.

Electromagnetic Compatibility Guidelines

This product was tested and complies with the regulatory

requirements and limits for electromagnetic compatibility (EMC)

as stated in the product specifications. These requirements and

limits are designed to provide reasonable protection against

harmful interference when the product is operated in its intended

operational electromagnetic environment.

This product is intended for use in industrial locations. As such,

there is no guarantee that harmful interference will not occur in

a particular installation, when the product is connected to a test

object, or if the product is used in residential areas. To minimize

the potential for the product to cause interference to radio and

television reception or to experience unacceptable performance

6|ni.com |NI 9514Operating Instructions and Specifications

degradation, install and use this product in strict accordance with

the instructions in the product documentation.

Furthermore, any changes or modifications to the product not

expressly approved by National Instruments could void your

authority to operate it under your local regulatory rules.

Caution To ensure compliance with the applicable

regulatory requirements, product installation requires

either special considerations or user-installed, add-on

devices. See the product installation instructions for

further information.

Caution The inputs/outputs of this product can be

damaged if subjected to Electrostatic Discharge (ESD). To

prevent damage, industry-standard ESD prevention

measures must be employed during installation,

maintenance, and operation.

Special Guidelines for Marine Applications

Some products are Lloyd’s Register (LR) Type Approved for

marine (shipboard) applications. To verify Lloyd’s Register

certification for a product, visit ni.com/certification and

NI 9514 Operating Instructions and Specifications |© National Instruments |7

search for the LR certificate, or look for the Lloyd’s Register mark

on the product label.

Caution In order to meet the EMC requirements for

marine applications, install the product in a shielded

enclosure with shielded and/or filtered power and

input/output ports. In addition, take precautions when

designing, selecting, and installing measurement probes

and cables to ensure that the desired EMC performance is

attained.

Connecting the NI 9514

The NI 9514 servo drive interface module is part of a family of

C Series motion modules. The module provides servo drive

interface signals for a single axis, a full set of motion I/O including

inputs for a home switch and limit switches, incremental encoder

inputs for position feedback, and 0 to 30 V digital input lines. The

NI 9514 also includes a processor to run the spline interpolation

engine and PID control loop. Working together they produce

smoother motion resulting in precise servo motion control.

8|ni.com |NI 9514Operating Instructions and Specifications

System Connection

The NI 9514 has two connectors, a 15-pin DSUB drive interface

connector and a 20-pin MDR feedback connector. The 15-pin

DSUB includes command signals for interfacing with servo

amplifiers or drives, a 0 to 30 V general-purpose digital input line,

and a 19 to 30 V input for power connection. Refer to Table 1 for

the DSUB connector pin assignments.

Note The remainder of this document does not

distinguish between drives and amplifiers. All

references to drives also apply to amplifiers.

The 20-pin MDR connector includes incremental encoder

feedback inputs, a +5 V output for encoder power, home, limit,

and position compare inputs, an output for position compare, an

additional 19 to 30 V input for power connection, and an additional

0 to 30 V general-purpose digital input line. Refer to Figure 2 for

the MDR connector pin assignments.

Note The NI 9514 requires an external power supply.

You can connect the external power supply to the Vsup

input provided on the DSUB or MDR connector. Do not

connect more than one external power supply to the

module.

NI 9514 Operating Instructions and Specifications |© National Instruments |9

NI 9514 Connection Options

National Instruments offers several options for connecting the

NI 9514 to servo drives. You can use the NI 9514/16 to AKD cable

to connect the NI 9514 to the AKD analog servo drive and AKM

series servo motors from NI. To connect to third-party servo drives

use the NI 951x Cable and Terminal Block Bundle. Refer to

Figure 3 for the 37-pin terminal block pin assignments. Refer to the

NI 951x User Manual, which you can download from ni.com/

manuals, for information about additional connection accessories

and cabling recommendations.

Tip NI offers AKD analog servo drives and matched

servo motors. Refer to Getting Started with NI 9514/16

C Series Drive Interface Modules and AKD Analog Servo

Drives for installation and configuration information.

Refer to the Getting Started with NI 951x C Series Drive

Interface Modules and LabVIEW for information about

using the NI 9514 with other devices.

How to Connect the NI 9514 to Drives and I/O

Complete the following steps to connect the NI 9514 servo drive

interface module to drives and other I/O.

Andere Handbücher für NI 9514

Inhaltsverzeichnis

Andere National Instruments Steuereinheit Handbücher

National Instruments

National Instruments sbRIO-9609 Bedienungsanleitung

National Instruments

National Instruments NI 9264 Bedienungsanleitung

National Instruments

National Instruments R Series Bedienungsanleitung

National Instruments

National Instruments SCC-A10 Bedienungsanleitung

National Instruments

National Instruments 9246 Bedienungsanleitung

National Instruments

National Instruments NI PXIe-8374 Bedienungsanleitung

National Instruments

National Instruments NI-9232 Bedienungsanleitung

National Instruments

National Instruments 9205 Handbuch

National Instruments

National Instruments PXI-2568 Bedienungsanleitung

National Instruments

National Instruments NI 9870 Bedienungsanleitung

National Instruments

National Instruments PXI-8214 Bedienungsanleitung

National Instruments

National Instruments SCC-CTR01 Bedienungsanleitung

National Instruments

National Instruments 7330 Bedienungsanleitung

National Instruments

National Instruments NI 9250 Bedienungsanleitung

National Instruments

National Instruments PXI-6682 Series Bedienungsanleitung

National Instruments

National Instruments PXIe-4302 Bedienungsanleitung

National Instruments

National Instruments 7340 Bedienungsanleitung

National Instruments

National Instruments NI 9246 Bedienungsanleitung

National Instruments

National Instruments FP-RLY-422 Bedienungsanleitung

National Instruments

National Instruments NI 9265 Bedienungsanleitung

National Instruments

National Instruments PXIe-4466 Bedienungsanleitung

National Instruments

National Instruments FieldPoint FP-1000 Bedienungsanleitung

National Instruments

National Instruments Phase Matrix PXI-1440 Bedienungsanleitung

National Instruments

National Instruments NI-SPEEDY-33 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung