National Instruments NI-SPEEDY-33 Bedienungsanleitung

INSTALLATIONGUIDE

NISPEEDY-33

P~ClCl J~

This installation guide describes how to install and configure the

NI SPEEDY-33DSP device for use with a Pc. Figure] depicts the

NI SPEEDY-33.

Ig~~!1

.O~~

1~~~~~~g~~lm

.OOOQ{JOOO, 0

1 Microphones

2 Power LED

3 Audio Stereo Input Port

4Audio Stereo Output Port

5 010 Out Port LEOs

6 Power Port

7 PC USB Port

8 Peripheral USB Port

Figure 1. NISPEEDY-33DSPDevice

'7 NATIONAL

"INSTRUMENTSN

Step1. InstalltheSoftwareandDrivers

LabVIEWDSPModule

Refer to the LabVIEWDSP Module Release Notes for software and driver

installation instructions.

VisualApplicationBuilderforInfinityProject(VAB)

Complete the following steps to install the VAB software and drivers.

I. Log on as an administrator or as a user with administrator privileges.

2. Insert the Visual Application Builder installation CD in the CD drive.

3. Click Step 1: Install VAB Software and follow the instructions that

appear on the screen.

After installing the software and drivers, click Finish.

Close the Infinity Kit Installation Tutorial and exit the VABinstaller.

Step2. UnpacktheDevice,Cable,andAccessories

Your device is shipped in an antistatic package to prevent electrostatic

damage (ESD) to the device and its components.

&Caution Never touch the exposed pins of connectors.

To avoid such damage, take the following precautions:

.Ground yourself using a grounding strap or by touching a grounded

object.

Touch the antistatic package to a metal part of the computer chassis

before removing the device from the package.

Remove the device from the package and inspect the device for loose

components or any sign of damage. Notify NI if the device appears

damaged in any way.Do not use a damaged device.

Store the device in the antistatic package when the device is not in use.

NISPEEDY-33Installation Guide 2ni.com

Step3. ConnecttheHardware

[

Refer to Figures I and 2 as you complete the following steps to connect the

NI SPEEDY-33 to a Pc. .

Figure 2. NISPEEDY-33 Installation

]. Power up your computer. Log on as an administrator or as a user with

administrator privileges.

2. Connect one end of the USB cable to the PC USB port on the

NI SPEEDY-33.

The cable connectors are different on each end. Only one end fits into

the PC USB port.

Connect the other end of the USB cable to a USB port on the Pc.

The USB cable also serves as the NI SPEEDY-33power supply. The

green power LED on the device lights.

Continue the hardware connection process by proceeding to the

Windows 2000 section or the Windows XP section.

@NationattnstrumentsCorporation 3NtSPEEDY-33tnstallationGuide

Windows2000

WindowsXP

NI SPEEDY-33Installation Guide

Windows recognizes any newly installed device andopens the Found New

Hardware window. Because the NI SPEEDY-33 driver was installed in

Step i. install the Software and Drivers, Windows 2000 f1l1dsthe driver

automatically.

Your computer is now set up so that the software can communicate with the

NI SPEEDY-33.

Windows recognizes any newly installed device and opens theFound New

Hardware Wizard. Complete the following steps to connect the

NI SPEEDY-33 with the NI SPEEDY-33 driver.

I. Select No, not this time. Click Next.

Welcome to the Found New

Hardware Wizard

Windows willsearch for cUlrent and updated so/tware by

looking on your computer. on the hardware installation CD. 01 on

the Windows Update Web site (with your permission].

Reo,>dow ;:)!'\'aG\:J~

Can Windows connect to Windows Update to search for

software?

0Yes. this time onl}'

0Yes. now and every time I connect a device

€I No. not this time

Click Next to continue.

~_._~~~_J Next >J

4ni.com

2. Select Install the software automatically (Recommended).

Thiswizardhelpsyouinstallsoftwarefor:

HyperceptionSPEEDY.33

If your hardware camewith an installation CD

or floppy disk. insert it now.

What doyouwantthewizardtodo?

€J Installthe softwareautomatically[Recommended]

0Installfroma listorspecificlocation[Advanced)

Infinity Kit (VAB)users must insert the Visual Application Builder

installation CD.

LabVIEW DSP Module users do not need to insert an installation CD

because the driver was installed in Step I. Install the Software and

Drivers.

3. Click Next.

Windows begins scanning the hard drive for the files it needs.

@NationalInstrumentsCorporation 5NI SPEEDY-33Installation Guide

l!J, Note A Hardware Installation alert might appear during the hardware scan. Click

Continue Anyway.

When Windows finishes detecting the required files, the following

window opens.

Completing the Found New

Hardware Wizard

The wizard has finished installing the software for:

4. Click Finish.

Your computer is now set up so that the software can communicate with the

NI SPEEDY-33.

NI SPEEDY-33Installation Guide 6ni.com

Step4. launchtheSoftware

LabVIEWDSPModule

Launch the LabVIEW DSP Module by selecting Start»AII Programs»

National Instruments»LabVIEW 7.1 Embedded Edition»LabVIEW.

Click Continue.

VAB

Launch VAB by selecting Start»AII Programs» VAB for INFINITY»

VAB or clicking the VAB icon on the desktop. Click OK.

Step5. TesttheNISPEEDY-33

LabVIEWDSPModule

Test the hardware connection and software configuration with the Blink

LED VI in the LabVIEW DSP Module by completing the following steps.

I. At the bottom of the LabVIEW 7.1 Embedded Edition dialog box,

select SPEEDY33 as the execution target.

2. Click the aITOWbutton on the Open button. Select Examples.

3. Open the Blink LED VI by selecting Toolkits and Modules»DSP»

Fundamentals»Blink LED.vi in the NI Example Finder. If you

cannot locate the VI, verify that you are browsing according to task.

You also can find the VI through the directory path,

C:\ProgramFiles\NationalInstruments\LabVIEW7.1

Embedded\examples\EmbeddedDSP\Blink LED.vi.

@National Instruments Corporation 7NI SPEEDY-33Instal/ation Guide

The Blink LED VI front panel opens.

4. Run the VI by clicking the Run button, shown at left, on the LabVIEW

front panel menu bar.

The VI front panel displays a blinking LED and a waveform. The

NI SPEEDY-33DIG out port LED #1 blinks in time with the LED on

the front panel. The NI SPEEDY-33DIG out port LED #3 stays lit the

entire time.

NI SPEEDY-33Installation Guide 8ni.com

If the NI SPEEDY-33 is not set up properly, the LabVIEW DSP

Module Status Monitor window displays the following message:

ERROR: Make sure target is communicating properly,

and no other software is attempting to use the DSP

hardware.If this occurs, check your connections and verify that the

power LED on the NI SPEEDY-33is lit. If your connections are good,

unplug the NI SPEEDY-33and repeat Step I. Install the Software and

Drivers.

5. After you have established that the NI SPEEDY-33is configured

properly, click the STOP button on the front panel.

Close LabVIEW. Do not save changes to the VI.

VAS

Test the hardware connection and software configuration with the Memory

Test in VAB by completing the following steps.

I. Select DSP Target»Driv,er Setup.

The following window opens.

Signal

Proce$sing

Engineering

E ducalional

Devicefor

Youth

2. Click the Test button.

A successful test will show that the device was found and the memory

test passed.

Board Found:

Memory Test:

Close J

@NationalInstrumentsCorporation 9NI SPEEDY-33Installation Guide

If your device does not pass the VABMemory Test, check your

connections and verify that the power LED on the NI SPEEDY-33is

lit. If yourconnections aregood, unplug theNI SPEEDY-33and repeat

Step I. Install the Software and Drivers.

After you have established that the NI SPEEDY-33is configured

properly, click the Close button.

Close the Memory Test and exit VAB.

WheretoGofromHere

The Getting Started with the LabVIEWDSP Module document has a

tutorial to familiarize you with the LabVIEW DSP Module. You can find

this document by selecting Start»AII Programs»National Instruments»

LabVIEW 7.1 Embedded Edition»LabVIEW Manuals»

DSP_Gettin~Started.pdf.

The VAB Starter's Guide has a tutorial to familiarize you with VAB.

Youcan find this document by selecting Start»AII Programs»

VAB for INFINITY»V AB User Manual.

The SPEEDY-]] UserManual contains information about the features

and functions of the digital signal processor, components, and interface

of the NI SPEEDY-33DSP device. Youcan find this document on the

NI SPEEDY.33 User Documentation CD.

The Connecting Accessories to the NI SPEEDY-33 document describes

third-party accessory connections for the NI SPEEDY.33 and Infinity Kit.

This document is only available on ni. corn/manuals.

All NI user documentation is available on the National Instruments Web

site at ni . corn/manuals.

WheretoGoforSupport

The National Instruments Web site is your complete resource for technical

support. At ni . com/ support you have access to everything from

troubleshooting and application development self-help resources to email

and phone assistance from NI Application Engineers.

National Instruments corporate headquarters is located at

I 1500 North Mopac Expressway, Austin, Texas, 78759.3504.

National Instruments also has offices located around the world to help

address your support needs. For telephone support in the United States,

create your service request at ni . com/support and follow the calling

NI SPEEDY.33Installation Guide 10 ni.com

Inhaltsverzeichnis

Andere National Instruments Steuereinheit Handbücher

National Instruments

National Instruments NI 9235 Bedienungsanleitung

National Instruments

National Instruments NI PXI-6682 Bedienungsanleitung

National Instruments

National Instruments 5174 Bedienungsanleitung

National Instruments

National Instruments Relay Module SCC-RLY01 Bedienungsanleitung

National Instruments

National Instruments NI 9758 Bedienungsanleitung

National Instruments

National Instruments PXIe-6674T Bedienungsanleitung

National Instruments

National Instruments SCXI-1521 Bedienungsanleitung

National Instruments

National Instruments NI 9425 Bedienungsanleitung

National Instruments

National Instruments SCXI-1120/D Handbuch

National Instruments

National Instruments PXIe-4302 Handbuch

National Instruments

National Instruments NI-9208 Handbuch

National Instruments

National Instruments NI 9503 Bedienungsanleitung

National Instruments

National Instruments SCC-DO01 Bedienungsanleitung

National Instruments

National Instruments SCC Series Bedienungsanleitung

National Instruments

National Instruments SCC-AI Series Bedienungsanleitung

National Instruments

National Instruments NI 9882 Bedienungsanleitung

National Instruments

National Instruments NI PXI-6682 Bedienungsanleitung

National Instruments

National Instruments PXI-6683 Series Bedienungsanleitung

National Instruments

National Instruments SCXI-1000 Bedienungsanleitung

National Instruments

National Instruments PXIe-6591R Bedienungsanleitung

National Instruments

National Instruments SCXI-1100 Bedienungsanleitung

National Instruments

National Instruments FieldPoint FP-AI-110 Bedienungsanleitung

National Instruments

National Instruments NI TB-4340 Bedienungsanleitung

National Instruments

National Instruments NI PXIe-7972R Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung