National Instruments PXIe-8245 Bedienungsanleitung

GETTING STARTED GUIDE

PXIe-8245

PXIe, 4-Port, 10/100/1000BASE-T PXI Ethernet Interface Module

This document describes how to install and configure the necessary hardware and software

components to begin using the PXIe-8245.

You need the following items to set up and use the PXIe-8245.

• PXIe-8245 GigE interface device

• Ethernet cable

• PXIe computer running Microsoft Windows 10 with at least one available slot

• PXI Platform Services software

• Optional software for developing applications:

– LabVIEW 2020

Note Before you begin, install and configure your chassis and controller.

Contents

Verifying the System Requirements..........................................................................................1

Unpacking the Kit..................................................................................................................... 2

PXIe-8245 Kit Contents............................................................................................................2

Preparing the Environment....................................................................................................... 2

Installing the Application Software and Driver........................................................................ 3

Installing the PXIe-8245........................................................................................................... 3

Confirming the Device is Recognized.............................................................................. 4

Front Panel................................................................................................................................ 4

Troubleshooting........................................................................................................................ 5

What Should I Do if the PXIe-8245 Does Not Appear in MAX?.................................... 5

Where to Go Next..................................................................................................................... 5

Worldwide Support and Services.............................................................................................. 6

Verifying the System Requirements

To use the PXIe-8245, your system must meet certain requirements. For more information

about minimum system requirements, recommended system, and supported application

development environments (ADEs), refer to the readme, which is installed or available at

ni.com/manuals.

Unpacking the Kit

Notice To prevent electrostatic discharge (ESD) from damaging the device, ground

yourself using a grounding strap or by holding a grounded object, such as your

computer chassis.

1. Touch the antistatic package to a metal part of the computer chassis.

2. Remove the device from the package and inspect the device for loose components or any

other sign of damage.

Notice Never touch the exposed pins of connectors.

Note Do not install a device if it appears damaged in any way.

3. Unpack any other items and documentation from the kit.

Store the device in the antistatic package when the device is not in use.

PXIe-8245 Kit Contents

The following items are included in the device kit:

• PXIe-8245

• Documentation:

–PXIe-8245 Getting Started Guide (this document)

–PXIe-8245 Safety, Environmental, and Regulatory Information

Preparing the Environment

Ensure the environment in which you are using the PXIe-8245 meets the following

specifications.

Operating environment

Ambient temperature range 0 °C to 55 °C

Relative humidity range 10% to 90%, noncondensing

Maximum altitude 2,000 m (800 mbar) (at 25 °C ambient

temperature)

Pollution Degree 2

Indoor use only.

Note For complete specifications, refer to the specifications document for your

device at ni.com/manuals.

2| ni.com | PXIe-8245 Getting Started Guide

Installing the Application Software and Driver

Before installing your hardware, you must install the application software and device driver.

Install the software in the following order:

1. Install PXI Platform Services.

2. Install LabVIEW (optional).

Installing the PXIe-8245

Notice To prevent damage to the PXIe-8245 caused by ESD or contamination,

handle the module using the edges or the metal bracket.

1. Ensure the AC power source is connected to the chassis before installing the module.

The AC power cord grounds the chassis and protects it from electrical damage while you

install the module.

2. Power off the chassis.

3. Inspect the slot pins on the chassis backplane for any bends or damage prior to

installation. Do not install a module if the backplane is damaged.

4. Remove the black plastic covers from all the captive screws on the module front panel.

5. Identify a supported slot in the chassis. The following figure shows the symbols that

indicate the slot types.

Figure 1. Chassis Compatibility Symbols

NI PXIe-1062Q

12 3 45

1. PXI Express System Controller Slot

2. PXI Peripheral Slot

3. PXI Express Hybrid Peripheral Slot

4. PXI Express System Timing Slot

5. PXI Express Peripheral Slot

6. Touch any metal part of the chassis to discharge static electricity.

7. Place the module edges into the module guides at the top and bottom of the chassis. Slide

the module into the slot until it is fully inserted.

8. Secure the module front panel to the chassis using the front-panel mounting screws.

Note Tightening the top and bottom mounting screws increases mechanical

stability and also electrically connects the front panel to the chassis, which can

improve the signal quality and electromagnetic performance.

9. Cover all empty slots using EMC filler panels or fill using slot blockers to maximize

cooling air flow, depending on your application.

PXIe-8245 Getting Started Guide | © National Instruments | 3

10. Power on the chassis.

Note The first time you start the development computer after installing the

hardware, allow several seconds for the drivers to load.

Confirming the Device is Recognized

To confirm that the device is properly installed and the hardware is recognized, complete the

following steps:

1. Select Start »All Programs »National Instruments »Measurement & Automation

Explorer to open Measurement & Automation Explorer (MAX).

2. Verify that the PXIe-8245 appears under My System »Devices and Interfaces .

Front Panel

The following figure shows the PXIe-8245 front panel.

Figure 2. PXIe-8245 Front Panel

PXIe-8245

1000BASE-T

The PXIe-8245 provides four standard Gigabit Ethernet ports (Port 0 to Port 3).

4| ni.com | PXIe-8245 Getting Started Guide

Table 1. Ethernet LED Status Definitions

LED Status Definition

Activity/Link Unlit No link

Green (Solid) Linked

Green (Blinking) Data activity

Link Speed Unlit 10 Mbps connection

Green 100 Mbps connection

Amber 1,000 Mbps connection

Troubleshooting

If an issue persists after you complete a troubleshooting procedure, contact NI technical

support or visit ni.com/support.

What Should I Do if the PXIe-8245 Does Not Appear in

MAX?

1. In the MAX configuration tree, expand Devices and Interfaces.

2. Expand the Chassis tree to see the list of installed hardware, and press <F5> to refresh

the list.

3. If the module is still not listed, power off the system, ensure that all hardware is correctly

installed, and restart the system.

4. Navigate to the Device Manager. Right-click the Start button, and select Device Manager

5. Verify the PXIe-8245 appears in the Device Manager.

a) Under an NI entry, confirm that a PXIe-8245 entry appears.

Note If you are using a PC with a device for PXI remote control system,

under System Devices, also confirm that no error conditions appear for the

PCI-to-PCI Bridge.

b) If error conditions appear, reinstall the PXI Platform Services driver.

Where to Go Next

Refer to the following figure for information about other product tasks and associated

resources for those tasks.

PXIe-8245 Getting Started Guide | © National Instruments | 5

SUPPORT

Services

ni.com/services

NI Community

ni.com/community

Software Support

ni.com/info>swsupport

Support

ni.com/support

SOFTWAREHARDWARE

Learn LabVIEW Basics

ni.com/gettingstarted

NI PXIe-8245 Specifications

ni.com/manuals

NI PXIe-8245 User Manual

ni.com/manuals

Worldwide Support and Services

The NI website is your complete resource for technical support. At ni.com/support, you have

access to everything from troubleshooting and application development self-help resources to

email and phone assistance from NI Application Engineers.

Visit ni.com/services for information about the services NI offers.

Visit ni.com/register to register your NI product. Product registration facilitates technical

support and ensures that you receive important information updates from NI.

NI corporate headquarters is located at 11500 North Mopac Expressway, Austin, Texas,

78759-3504, USA. For up-to-date contact information for your location, visit ni.com/contact.

6| ni.com | PXIe-8245 Getting Started Guide

Information is subject to change without notice. Refer to the NI Trademarks and Logo Guidelines at ni.com/trademarks for

information on NI trademarks. Other product and company names mentioned herein are trademarks or trade names of their

respective companies. For patents covering NI products/technology, refer to the appropriate location: Help»Patents in your

software, the patents.txt file on your media, or the National Instruments Patent Notice at ni.com/patents. You can find

information about end-user license agreements (EULAs) and third-party legal notices in the readme file for your NI product. Refer

to the Export Compliance Information at ni.com/legal/export-compliance for the NI global trade compliance policy and how

to obtain relevant HTS codes, ECCNs, and other import/export data. NI MAKES NO EXPRESS OR IMPLIED WARRANTIES AS

TO THE ACCURACY OF THE INFORMATION CONTAINED HEREIN AND SHALL NOT BE LIABLE FOR ANY ERRORS. U.S.

Government Customers: The data contained in this manual was developed at private expense and is subject to the applicable

limited rights and restricted data rights as set forth in FAR 52.227-14, DFAR 252.227-7014, and DFAR 252.227-7015.

378323A-01 July 3, 2020

Inhaltsverzeichnis

Andere National Instruments Steuereinheit Handbücher

National Instruments

National Instruments PXIe-8246 Bedienungsanleitung

National Instruments

National Instruments NI PXI-6682 Bedienungsanleitung

National Instruments

National Instruments PXIe-8240 Bedienungsanleitung

National Instruments

National Instruments sbRIO-9205 Bedienungsanleitung

National Instruments

National Instruments NI PXI-2585 Bedienungsanleitung

National Instruments

National Instruments PCIe-7858 Bedienungsanleitung

National Instruments

National Instruments NI 9760 Bedienungsanleitung

National Instruments

National Instruments NI 6013 Kurzanleitung

National Instruments

National Instruments R Series Bedienungsanleitung

National Instruments

National Instruments PXIe-4302 Handbuch

National Instruments

National Instruments NI 9214 Bedienungsanleitung

National Instruments

National Instruments SCXI-1141 Bedienungsanleitung

National Instruments

National Instruments NI 9226 Bedienungsanleitung

National Instruments

National Instruments PXIe-8830mc Bedienungsanleitung

National Instruments

National Instruments NI PXI-8840 Bedienungsanleitung

National Instruments

National Instruments NI 9242 Bedienungsanleitung

National Instruments

National Instruments NI 9425 Bedienungsanleitung

National Instruments

National Instruments NI 9472 Bedienungsanleitung

National Instruments

National Instruments NI PXI-665 Series Bedienungsanleitung

National Instruments

National Instruments SCC-PWR02 Bedienungsanleitung

National Instruments

National Instruments NI PXIe-7972R Bedienungsanleitung

National Instruments

National Instruments CFP-TC-120 Bedienungsanleitung

National Instruments

National Instruments NI 9218 Bedienungsanleitung

National Instruments

National Instruments NI 9401 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung