National Instruments FieldPoint cFP-2120 Bedienungsanleitung

QUICK START GUIDE

FieldPoint cFP-2120

Mount the Compact FieldPoint Backplane

You can mount the cFP-BP-

backplane on a 35 mm DIN rail, on a panel, or in a

standard 19 in. rack. Before using any of these mounting methods, record the

serial number from the back of the backplane.

Each set of mounting instructions in this document includes an instruction to

connect the protective earth (PE) ground terminal on the cFP-BP-

backplane to

the system safety ground. The backplane PE ground terminal has the following

symbol stamped beside it: . Connect the backplane PE ground terminal to the

system safety ground using 14 AWG (1.6 mm) wire with a ring lug. Use the

5/16 in. panhead screw shipped with the backplane to secure the ring lug to

the backplane PE ground terminal.

What You Need to Get Set Up

• cFP-2120 LabVIEW RT controller

• Mounting hardware (DIN rail, panel-

mount, or rack-mount accessory)

• I/O module(s)

• cFP-BP-

backplane, connector

blocks, cables

• 11–30 VDC power supply

• Accessories: Ethernet cable, number

2 Phillips screwdriver

• PC running Windows

• FieldPoint software 4.1.1 or later

• LabVIEW Real-Time Module

™

cFP-2120 Quick Start Guide 2 ni.com

Caution Keep in mind these requirements for space and cabling

clearance:

• Allow at least 51 mm (2 in.) all around the backplane for air

circulation.

• Allow 38 mm (1.5 in.) below and 51 mm (2 in.) above the controller

for cabling clearance.

Cabling

Clearance

4 slots = 246 mm (9.68 in.)

8 slots = 441 mm (17.4 in.)

Cooling Outline

51 mm (2 in.)

Cooling Outline

51 mm (2 in.)

Min. 182 mm (7.18 in.)

106 mm (4.18 in.)

Cabling

Clearance

Cooling Outline

51 mm (2 in.)

All Around

4 slots = 246 mm (9.68 in.)

8 slots = 441 mm (17.4 in.)

127 mm

(5.00 in.)

Min. 165 mm

(6.50 in.)

National Instruments Corporation 3 cFP-2120 Quick Start Guide

Caution If you are using UL Recognized I\O modules with the

Compact FieldPoint system, you must install the entire system in a

suitably rated, UL Listed NEMA or IP enclosure.

Caution NI recommends that you use one of the mounting systems

described in this document. If you decide to use a custom mounting

solution, make sure that the screws you use are short enough to fit in

the holes in the backplane. The screw holes are 5 mm (0.2 in.) deep.

cFP-2120 Quick Start Guide 4 ni.com

Mounting the Backplane on a Panel

A. Fasten the panel-mount plates to the back of the cFP-BP-

using a number

2 Phillips screwdriver and the 8-32 ×5/16 in. countersink screws shipped

with the kit.

Caution Do not use screws longer than 5/16 in. to fasten the panel-

mount plates to the backplane.

TIONAL

INSTRUMENTS

102 mm

(4 in.)

457 mm (18 in.)

National Instruments Corporation 5 cFP-2120 Quick Start Guide

260 mm (10.25 in.)

102 mm

(4 in.)

104.78 mm

(4.1 in.)

63.50 mm

(2.5 in.)

22.23 mm

(0.9 in.)

33.15 mm

(1.3 in.)

129.54 mm

(5.1 in.)

311.40 mm

(12.3 in.)

387.60 mm

(15.3 in.)

407.80 mm

(16.1 in.)

127.00 mm

(5.0 in.)

440.94 mm

(17.4 in.)

cFP-2120 Quick Start Guide 6 ni.com

B. Bolt or screw the panel-mount accessory to a panel.

C. Connect the PE ground terminal on the cFP-BP-

to safety ground.

Caution Disconnect power before removing the backplane from

the panel.

Mounting the Backplane on a DIN Rail

NI recommends DIN rail mounting for the cFP-BP-4 only. Use panel mounting

or rack mounting for the cFP-BP-8. The DIN rail mounting kit is NI part number

778614-01

A. Fasten the DIN rail clip to the cFP-BP-4 using a number 2 Phillips

screwdriver and the 8-32 ×5/16 in. countersink screws shipped with the

clip.

104.74 mm

(4.1 in.)

63.46 mm

(2.5 in.)

127.00 mm

(5.0 in.)

22.19 mm

(0.9 in.)

34.04 mm

(1.3 in.)

84.84 mm

(3.3 in.)

161.04 mm

(6.3 in.)

211.84 mm

(8.3 in.)

245.87 mm

(9.6 in.)

National Instruments Corporation 7 cFP-2120 Quick Start Guide

Caution Do not use screws longer than 5/16 in. to fasten the DIN rail

clip to the backplane.

B. Insert one edge of the DIN rail into the deeper opening of the DIN rail clip.

C. Press down firmly on the backplane to compress the spring until the clip

locks in place on the DIN rail.

D. Connect the PE ground terminal on the cFP-BP-4 to safety ground.

Caution Disconnect power before removing the backplane from the

DIN rail.

TIONAL

INSTRUMENTS

cFP-2120 Quick Start Guide 8 ni.com

Mounting the Backplane in a Standard 19-in. Rack

A. Fasten the rack-mount bracket to the back of the cFP-BP-

using the

captive screws on the bracket.

TIONAL

INSTRUMENTS

National Instruments Corporation 9 cFP-2120 Quick Start Guide

B. Bolt the rack-mount accessory to a standard 19-in. rack.

C. Connect the PE ground terminal on the cFP-BP-

to safety ground.

Caution Disconnect power before removing the backplane from the

DIN rail.

TIONAL

INSTRUMENTS

cFP-2120 Quick Start Guide 10 ni.com

Install the cFP-2120 Controller on the Backplane

A. Make sure that no power is connected to the controller.

B. Make sure that the cFP-2120 controller is right side up with the NI logo at

the top, and align the captive screws on the controller with the holes on the

backplane.

C. Seat the card edge at the back of the controller in the card-edge connector

on the backplane.

D. Press the controller firmly to seat it on the backplane.

E. Using a number 2 Phillips screwdriver with a shank of at least 64 mm

(2.5 in.) length, tighten the captive screws to 1.1 N ⋅m (10 lb ⋅in.) of torque.

TIONAL

INSTRUMENTS

Inhaltsverzeichnis

Andere National Instruments Controller Handbücher

National Instruments

National Instruments PXI NI PXI-8105 Bedienungsanleitung

National Instruments

National Instruments NI-488.2M Bedienungsanleitung

National Instruments

National Instruments PXIe-8106 Bedienungsanleitung

National Instruments

National Instruments 7932 Bedienungsanleitung

National Instruments

National Instruments GPIB-232 Bedienungsanleitung

National Instruments

National Instruments RT Series Bedienungsanleitung

National Instruments

National Instruments sbRIO-9638 Bedienungsanleitung

National Instruments

National Instruments NI PXI-6653 Bedienungsanleitung

National Instruments

National Instruments PXI-7356 Bedienungsanleitung

National Instruments

National Instruments NI cRIO-9024 Bedienungsanleitung

National Instruments

National Instruments cDAQ-9132 Bedienungsanleitung

National Instruments

National Instruments sbRIO-9860 Bedienungsanleitung

National Instruments

National Instruments RMC-8356 Bedienungsanleitung

National Instruments

National Instruments NI cDAQ-9134 Betriebsanleitung

National Instruments

National Instruments NI 7340 Bedienungsanleitung

National Instruments

National Instruments PXI-8106 Bedienungsanleitung

National Instruments

National Instruments Two-Slot Embedded Controller NI PXI-8183 Bedienungsanleitung

National Instruments

National Instruments cRIO-9075 Bedienungsanleitung

National Instruments

National Instruments NI-Motion Bedienungsanleitung

National Instruments

National Instruments Network Adapter NI PXIe-6672 Bedienungsanleitung

National Instruments

National Instruments cRIO-9038 Bedienungsanleitung

National Instruments

National Instruments IC-3120 Bedienungsanleitung

National Instruments

National Instruments NI 8350 Bedienungsanleitung

National Instruments

National Instruments FlexRIO NI-7931R Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung