National Instruments 9220 Handbuch

CALIBRATION PROCEDURE

NI 9220

This document contains the verification and adjustment procedures for the NI 9220. In this

document, the NI 9220 with spring terminal and the NI 9220 with DSUB are referred to

inclusively as the NI 9220. For more information about calibration solutions, visit

ni.com/calibration.

Contents

Software Requirements............................................................................................................. 2

Documentation.......................................................................................................................... 2

Test Equipment......................................................................................................................... 3

Test Conditions......................................................................................................................... 3

Initial Setup............................................................................................................................... 3

Verification ............................................................................................................................... 4

Adjustment................................................................................................................................ 5

EEPROM Update ..................................................................................................................... 6

Re-Verification ......................................................................................................................... 6

Accuracy Under Calibration Conditions .................................................................................. 7

NI Services ............................................................................................................................... 7

2|ni.com |NI 9220 Calibration Procedure

Software Requirements

Calibrating the NI 9220 requires the installation of NI-DAQmx 9.6 or later on the calibration

system. You can download NI-DAQmx from ni.com/downloads. NI-DAQmx supports

LabVIEW, LabWindows™/CVI™, ANSI C, and .NET. When you install NI-DAQmx, you only

need to install support for the application software that you intend to use.

Documentation

Consult the following documents for information about the NI 9220, NI-DAQmx, and your

application software. All documents are available on ni.com and help files install with the

software.

NI cDAQ-9174/9178 Quick Start

NI-DAQmx installation and hardware setup

NI 9220 User Guide and Specifications

NI 9220 specific information, specifications, and calibration interval

NI-DAQmx Readme

Operating system and application software support in NI-DAQmx

LabVIEW Help

LabVIEW programming concepts and reference information about NI-DAQmx

VIs and functions

NI-DAQmx C Reference Help

Reference information for NI-DAQmx C functions and NI-DAQmx C properties

NI-DAQmx .NET Help Support for Visual Studio

Reference information for NI-DAQmx .NET methods and NI-DAQmx .NET

properties, key concepts, and a C enum to .NET enum mapping table

NI 9220 Calibration Procedure |© National Instruments Corporation |3

Test Equipment

Table 1 lists the equipment recommended for the performance verification and adjustment

procedures. If the recommended equipment is not available, select a substitute using the

requirements listed in Table 1.

Test Conditions

The following setup and environmental conditions are required to ensure the NI 9220 meets

published specifications.

• Keep connections to the NI 9220 as short as possible. Long cables and wires act as

antennae, picking up extra noise that can affect measurements.

• Verify that all connections to the NI 9220 are secure.

• Use shielded copper wire for all cable connections to the NI 9220. Use twisted-pairs wire

to eliminate noise and thermal offsets.

• Maintain an ambient temperature of 23 °C ±5 °C.

• Keep relative humidity below 80%.

• Allow a warm-up time of at least 10 minutes to ensure that the NI 9220 measurement

circuitry is at a stable operating temperature.

Initial Setup

Complete the following steps to set up the NI 9220.

1. Install NI-DAQmx.

2. Make sure the NI cDAQ-9178 power source is not connected.

3. Install the module in slot 8 of the NI cDAQ-9178 chassis. Leave slots 1 through 7 of the

NI cDAQ-9178 chassis empty.

4. Connect the NI cDAQ-9178 chassis to your host computer.

5. Connect the power source to the NI cDAQ-9178 chassis.

Table 1. Recommended Equipment

Equipment

Recommended

Model Requirements

Calibrator Fluke 5700A Use a high-precision voltage source with an

accuracy of ≤15 ppm and an output impedance

of ≤50 Ω.

Chassis NI cDAQ-9178 —

DSUB Connection

Accessory

NI 9923 —

4|ni.com |NI 9220 Calibration Procedure

6. Launch Measurement & Automation Explorer (MAX).

7. Right-click the device name and select Self-Test to ensure that the module is working

properly.

Verification

The following performance verification procedure describes the sequence of operation and test

points required to check the NI 9220 and assumes that adequate traceable uncertainties are

available for the calibration references.

Accuracy Verification

Complete the following procedure to determine the As-Found status of the NI 9220.

1. Set the calibrator to Standby mode (STBY).

2. Connect the NI 9220 to the calibrator as shown in Figure 1.

Figure 1. Accuracy Verification Connections

Note If the calibrator outputs are truly floating, connect the negative output to a

quiet earth ground as well as COM to give the entire system a ground reference.

3. Set the calibrator voltage to a Test Point value indicated in Table 4.

4. Set the calibrator to Operate mode (OPR).

5. Acquire and average samples.

a. Create and configure an AI voltage channel according to Table 2.

1 Connections when using a calibrator with a guard connection.

2 Connections when using a calibrator with no guard connection.

Table 2. NI 9220 AI Voltage Channel Configuration

Input Range

Scaled Units Terminal ConfigurationMin Max

-10 10 Vo l t s Differential

NI 9220Calibrator

AIx–

AIx+

COM

Guard

NI 9220Calibrator

AIx–

AIx+

COM

NI 9220 Calibration Procedure |© National Instruments Corporation |5

b. Configure the AI voltage channel timing according to Table 3.

c. Start the task.

d. Read samples from the NI 9220.

e. Average the samples.

f. Clear the task.

6. Compare the average of the samples to the test limits in Table 4.

Note The test limits listed in Table 4 are derived using the values in Table 6.

7. Repeat steps 3 through 6 for each Test Point in Table 4.

8. Set the calibrator to Standby mode (STBY).

9. Disconnect the NI 9220 from the calibrator.

10. Repeat steps 1 through 9 for each channel on the NI 9220.

Adjustment

The following performance adjustment procedure describes the sequence of operation required

to adjust the NI 9220.

Accuracy Adjustment

Complete the following procedure to adjust the accuracy performance of the NI 9220.

1. Set the calibrator to Standby mode (STBY).

2. Connect the NI 9220 to the calibrator as shown in Figure 1.

3. Adjust the NI 9220.

a. Initialize a calibration session on the NI 9220. The default password is NI.

b. Input the external temperature in degrees Celsius.

Table 3. NI 9220 Timing Configuration

Samples Per Channel Acquisition Mode Rate (kS/s)

10,000 Finite 100

Table 4. NI 9220 Test Limits

Range (V) Test Point 1-Year Limits

Min Max Location Value (V) Lower Limit (V) Upper Limit (V)

-10.000 10.000 Max 9.500000 9.497865 9.502135

-10.000 10.000 Mid 0.000000 -0.00090 0.00090

-10.000 10.000 Min -9.500000 -9.502135 -9.497865

6|ni.com |NI 9220 Calibration Procedure

c. Call the NI 9220 get C Series adjustment points function to obtain an array of

recommended calibration voltages for the NI 9220.

d. Set the calibrator to a reference value determined by the array of recommended

calibration voltages.

e. Set the calibrator to Operate mode (OPR).

f. Call and configure the NI 9220 adjustment function according to Table 5.

g. Set the calibrator to Standby mode (STBY).

h. Repeat steps d through g for each calibration voltage in the array.

i. Close the calibration session.

4. Disconnect the NI 9220 from the calibrator.

5. Repeat steps 1 through 4 for each channel on the NI 9220.

EEPROM Update

When an adjustment procedure is completed, the NI 9220 internal calibration memory

(EEPROM) is immediately updated.

If you do not want to perform an adjustment, you can update the calibration date and onboard

calibration temperature without making any adjustments by initializing an external calibration,

setting the C Series calibration temperature, and closing the external calibration.

Re-Verification

Repeat the Verification section to determine the As-Left status of the device.

Note If any test fails Re-Verification after performing an adjustment, verify that

you have met the Test Conditions before returning your device to NI. Refer to NI

Services section for assistance in returning the device to NI.

Table 5. Adjustment Configuration

Physical Channel Reference Value

cDAQMod8/aixThe reference value from the array of adjustment points

372220B-01 Jun21

Information is subject to change without notice. Refer to the NI Trademarks and Logo Guidelines at ni.com/trademarks for more

information on NI trademarks. Other product and company names mentioned herein are trademarks or trade names of their respective

companies. For patents covering NI products/technology, refer to the appropriate location: Help»Patents in your software, the patents.txt

file on your media, or the National Instruments Patents Notice at ni.com/patents. You can find information about end-user license

agreements (EULAs) and third-party legal notices in the readme file for your NI product. Refer to the Export Compliance Information at

ni.com/legal/export-compliance for the NI global trade compliance policy and how to obtain relevant HTS codes, ECCNs, and

other import/export data. NI MAKES NO EXPRESS OR IMPLIED WARRANTIES AS TO THE ACCURACY OF THE INFORMATION

CONTAINED HEREIN AND SHALL NOT BE LIABLE FOR ANY ERRORS. U.S. Government Customers: The data contained in this manual

was developed at private expense and is subject to the applicable limited rights and restricted data rights as set forth in FAR 52.227-14, DFAR

252.227-7014, and DFAR 252.227-7015.

Accuracy Under Calibration Conditions

The following calibration specifications are valid under the following conditions:

• Ambient temperature 23 ±5 °C

• NI 9220 installed in slot 8 of an NI cDAQ-9178 chassis

• Slots 1 through 7 of the NI cDAQ-9178 chassis are empty

Note The limits listed in Table 4 are derived using the values in Table 6.

Note For operational specifications, refer to the most recent NI 9220 User Guide

and Specifications online at ni.com/manuals.

NI Services

Visit ni.com/support to find support resources including documentation, downloads, and

troubleshooting and application development self-help such as tutorials and examples.

Visit ni.com/services to learn about NI service offerings such as calibration options, repair,

and replacement.

Visit ni.com/register to register your NI product. Product registration facilitates technical

support and ensures that you receive important information updates from NI.

NI corporate headquarters is located at 11500 North Mopac Expressway, Austin, Texas,

78759-3504, USA.

Table 6. NI 9220 Accuracy Under Calibration Conditions

Gain Error Offset Error

0.013% 0.90 mV

Andere Handbücher für 9220

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere National Instruments E/A-System Handbücher

National Instruments

National Instruments NI660 Series Bedienungsanleitung

National Instruments

National Instruments 653 Series Bedienungsanleitung

National Instruments

National Instruments 6738 Handbuch

National Instruments

National Instruments 9213E Bedienungsanleitung

National Instruments

National Instruments NI PXI-7851 Bedienungsanleitung

National Instruments

National Instruments NI 9381 Bedienungsanleitung

National Instruments

National Instruments E Series Bedienungsanleitung

National Instruments

National Instruments FIELDPOINT FP-DO-403 Bedienungsanleitung

National Instruments

National Instruments NI 9216 Bedienungsanleitung

National Instruments

National Instruments AT E Series Bedienungsanleitung

National Instruments

National Instruments R Series Bedienungsanleitung

National Instruments

National Instruments NI USB-6008 Bedienungsanleitung

National Instruments

National Instruments SCC-AI Series Bedienungsanleitung

National Instruments

National Instruments 9252 Handbuch

National Instruments

National Instruments PXIe-4339 Bedienungsanleitung

National Instruments

National Instruments PCIe-784 R Series Bedienungsanleitung

National Instruments

National Instruments PCIe-7856R Bedienungsanleitung

National Instruments

National Instruments NI 9754 Bedienungsanleitung

National Instruments

National Instruments NI 6583R Bedienungsanleitung

National Instruments

National Instruments NI 9231 Handbuch

National Instruments

National Instruments DAQ PCI-1200 Bedienungsanleitung

National Instruments

National Instruments 9237 Handbuch

National Instruments

National Instruments NI PCIe-7821R Bedienungsanleitung

National Instruments

National Instruments PXI-7842 Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung