National Instruments NI 9205 Bedienungsanleitung
GETTING STARTED GUIDE
NI 9205
16 AI Differential/32 AI Single-Ended, ±200 mV
to ±10 V, 16 Bit, 250 kS/s Aggregate
This document explains how to connect to the NI 9205. In this
document, the NI 9205 with spring terminal and the NI 9205 with
DSUB are referred to inclusively as the NI 9205.
Note Before you begin, complete the software and
hardware installation procedures in your chassis
documentation.
Note The guidelines in this document are specific to
the NI 9205. The other components in the system might
not meet the same safety ratings. Refer to the
documentation for each component in the system to
determine the safety and EMC ratings for the entire
system.
Caution Electrostatic Discharge (ESD) can damage
the NI 9205 with spring terminal. To prevent damage,
use industry-standard ESD prevention measures during
installation, maintenance, and operation.
Safety Guidelines
Operate the NI 9205 only as described in this document.
2| ni.com | NI 9205 Getting Started Guide
Caution This icon denotes a caution, which advises
you to consult documentation where this symbol is
marked.
Caution Do not operate the NI 9205 in a manner not
specified in this document. Product misuse can result in
a hazard. You can compromise the safety protection
built into the product if the product is damaged in any
way. If the product is damaged, return it to NI for
repair.
Hazardous Voltage This icon denotes a warning
advising you to take precautions to avoid electrical
shock with the NI 9205 with spring terminal .
Safety Voltages
Connect only voltages that are within the following limits:
Maximum voltage1
Channel-to-COM ±30 V DC
1The maximum voltage that can be applied or output between AI and COM
without creating a safety hazard.
NI 9205 Getting Started Guide | © National Instruments | 3
NI 9205 with Spring Terminal Isolation Voltages
Channel-to-channel None
Channel-to-earth ground
Continuous 250 V RMS,
Measurement Category II
Withstand up to
5,000 m
3,000 V RMS, verified by a 5 s
dielectric withstand test
Measurement Category II is for measurements performed on
circuits directly connected to the electrical distribution system.
This category refers to local-level electrical distribution, such as
that provided by a standard wall outlet, for example, 115 V for
U.S. or 230 V for Europe.
Caution Do not connect the NI 9205 with spring
terminal to signals or use for measurements within
Measurement Categories III or IV.
NI 9205 with DSUB Isolation Voltages
Channel-to-channel None
4| ni.com | NI 9205 Getting Started Guide
Channel-to-earth ground
Continuous 60 V DC, Measurement
Category I
Withstand
up to 2,000 m 1,000 V RMS, verified by a 5 s
dielectric withstand test
up to 5,000 m 500 V RMS
Measurement Category I is for measurements performed on
circuits not directly connected to the electrical distribution system
referred to as MAINS voltage. MAINS is a hazardous live
electrical supply system that powers equipment. This category is
for measurements of voltages from specially protected secondary
circuits. Such voltage measurements include signal levels, special
equipment, limited-energy parts of equipment, circuits powered
by regulated low-voltage sources, and electronics.
Caution Do not connect the NI 9205 with DSUB to
signals or use for measurements within Measurement
Categories II, III, or IV.
NI 9205 Getting Started Guide | © National Instruments | 5
Note Measurement Categories CAT I and CAT O are
equivalent. These test and measurement circuits are for
other circuits not intended for direct connection to the
MAINS building installations of Measurement
Categories CAT II, CAT III, or CAT IV.
Safety Guidelines for Hazardous Voltages
You can connect hazardous voltages only to the
NI 9205 with spring terminal . Do not connect hazardous
voltages to the NI 9205 with DSUB.
If hazardous voltages are connected to the device, take the
following precautions. A hazardous voltage is a voltage greater
than 42.4 Vpk voltage or 60 VDC to earth ground.
Caution Ensure that hazardous voltage wiring is
performed only by qualified personnel adhering to local
electrical standards.
Caution Do not mix hazardous voltage circuits and
human-accessible circuits on the same module.
Caution Ensure that devices and circuits connected to
the module are properly insulated from human contact.
6| ni.com | NI 9205 Getting Started Guide
Caution When module terminals are hazardous
voltage LIVE (>42.4 Vpk/60 VDC), you must ensure
that devices and circuits connected to the module are
properly insulated from human contact. You must use
the NI 9940 backshell kit to ensure that the terminals
are not accessible.
Safety Guidelines for Hazardous Locations
The NI 9205 is suitable for use in Class I, Division 2, Groups A,
B, C, D, T4 hazardous locations; Class I, Zone 2, AEx nA IIC T4
Gc and Ex nA IIC T4 Gc hazardous locations; and nonhazardous
locations only. Follow these guidelines if you are installing the
NI 9205 in a potentially explosive environment. Not following
these guidelines may result in serious injury or death.
Caution Do not disconnect I/O-side wires or
connectors unless power has been switched off or the
area is known to be nonhazardous.
Caution Do not remove modules unless power has
been switched off or the area is known to be
nonhazardous.
NI 9205 Getting Started Guide | © National Instruments | 7
Caution Substitution of components may impair
suitability for Class I, Division 2, or Zone 2.
Caution The system must be installed in an enclosure
certified for the intended hazardous (classified)
location, having a tool secured cover/door, where a
minimum protection of at least IP54 is provided.
Special Conditions for Hazardous Locations Use
in Europe and Internationally
The NI 9205 has been evaluated as Ex nA IIC T4 Gc equipment
under DEMKO 03 ATEX 0324020X and is IECEx UL 14.0089X
certified. Each NI 9205 is marked II 3G and is suitable for use
in Zone 2 hazardous locations, in ambient temperatures of -40 °C
≤ Ta ≤ 70 °C. If you are using the NI 9205 in Gas Group IIC
hazardous locations, you must use the device in an NI chassis that
has been evaluated as Ex nC IIC T4, Ex IIC T4, Ex nA IIC T4, or
Ex nL IIC T4 equipment.
Caution Transient protection shall be provided that is
set at a level not exceeding 140% of the peak rated
voltage value of 85 V at the supply terminals to the
equipment.
8| ni.com | NI 9205 Getting Started Guide
Caution The system shall only be used in an area of
not more than Pollution Degree 2, as defined in
IEC/EN 60664-1.
Caution The system shall be mounted in an
ATEX/IECEx-certified enclosure with a minimum
ingress protection rating of at least IP54 as defined in
IEC/EN 60079-15.
Caution The enclosure must have a door or cover
accessible only by the use of a tool.
Electromagnetic Compatibility Guidelines
This product was tested and complies with the regulatory
requirements and limits for electromagnetic compatibility (EMC)
stated in the product specifications. These requirements and
limits provide reasonable protection against harmful interference
when the product is operated in the intended operational
electromagnetic environment.
This product is intended for use in industrial locations. However,
harmful interference may occur in some installations, when the
product is connected to a peripheral device or test object, or if the
NI 9205 Getting Started Guide | © National Instruments | 9
product is used in residential or commercial areas. To minimize
interference with radio and television reception and prevent
unacceptable performance degradation, install and use this
product in strict accordance with the instructions in the product
documentation.
Furthermore, any changes or modifications to the product not
expressly approved by National Instruments could void your
authority to operate it under your local regulatory rules.
Caution To ensure the specified EMC performance of
the NI 9205 with DSUB, the length of all I/O cables
must be no longer than 30 m (100 ft).
Caution To ensure the specified EMC performance,
operate the NI 9205 with DSUB only with shielded
cables and accessories. Do not use unshielded cables or
accessories unless they are installed in a shielded
enclosure with properly designed and shielded input/
output ports and connected to the product using a
shielded cable. If unshielded cables or accessories are
not properly installed and shielded, the EMC
specifications for the product are no longer guaranteed.
10 | ni.com | NI 9205 Getting Started Guide
Andere Handbücher für NI 9205
2
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere National Instruments E/A-System Handbücher
National Instruments
National Instruments NI VISION PCI-8254R Bedienungsanleitung
National Instruments
National Instruments PXI-7842 Bedienungsanleitung
National Instruments
National Instruments BNC-2090A Bedienungsanleitung
National Instruments
National Instruments 9211 Handbuch
National Instruments
National Instruments REM-11120 Bedienungsanleitung
National Instruments
National Instruments Interface Device NI PCI-1426 Bedienungsanleitung
National Instruments
National Instruments SC-2071 Bedienungsanleitung
National Instruments
National Instruments sbRIO-9219 Bedienungsanleitung
National Instruments
National Instruments NI-9207 Handbuch
National Instruments
National Instruments NI USB-6000 Bedienungsanleitung
National Instruments
National Instruments NI 9225 Bedienungsanleitung
National Instruments
National Instruments USB-6525 Bedienungsanleitung
National Instruments
National Instruments NI 9219 Bedienungsanleitung
National Instruments
National Instruments NI-9244 Bedienungsanleitung
National Instruments
National Instruments DAQPad-6508 Bedienungsanleitung
National Instruments
National Instruments NI-9361 Bedienungsanleitung
National Instruments
National Instruments SC Express PXIe-4309 Bedienungsanleitung
National Instruments
National Instruments DAQ M Series Bedienungsanleitung
National Instruments
National Instruments NI 6238 Bedienungsanleitung
National Instruments
National Instruments USB-TC01 Handbuch
Beliebte E/A-System Handbücher anderer Marken
WAGO
WAGO 750-344 Bedienungsanleitung
Teknim
Teknim TWM-1887 Bedienungsanleitung
Intelligent Appliance
Intelligent Appliance IA-2662-E Bedienungsanleitung
BERGHOF
BERGHOF ECC DIO 16/16 Bedienungsanleitung
Advantech
Advantech PCM-27J3AU Installations- und Betriebshandbuch
Festo
Festo CP-E08-M12-CL Bedienungsanleitung
