National Instruments NI-9228 Handbuch

NI-9228

CALIBRATION PROCEDURE

NI 9228

8 AI, ±60 V, 24 Bit, 1 kS/s/ch Simultaneous

This document contains the verification and adjustment procedures for NI 9228. For more

information about calibration solutions, visit ni.com/calibration.

Contents

Software.................................................................................................................................... 1

Documentation.......................................................................................................................... 1

Test Equipment..........................................................................................................................2

Test Conditions..........................................................................................................................3

Initial Setup............................................................................................................................... 3

Verification................................................................................................................................3

Accuracy Verification....................................................................................................... 3

Adjustment................................................................................................................................ 5

Accuracy Adjustment........................................................................................................5

EEPROM Update......................................................................................................................6

Reverification............................................................................................................................6

Accuracy under Calibration Conditions....................................................................................6

Worldwide Support and Services.............................................................................................. 6

Software

Calibrating the NI 9228 requires the installation of NI-DAQmx 18.1 or later on the calibration

system.

You can download NI-DAQmx from ni.com/downloads. NI-DAQmx supports LabVIEW,

LabWindows™/CVI™, ANSI C, and .NET. When you install NI-DAQmx, you only need to

install support for the application software that you intend to use.

Documentation

Consult the following documents for information about the NI 9228, NI-DAQmx, and your

application software. All documents are available on ni.com and help files install with the

software.

NI cDAQ-9174/9178 USB Chassis Quick Start

NI-DAQmx installation and hardware setup

NI 9228 Getting Started Guide

NI 9228 connection information

NI 9228 Datasheet

NI 9228 circuitry and specifications

NI-DAQmx Readme

Operating system and application software support in NI-DAQmx

LabVIEW Help

LabVIEW programming concepts and reference information about NI-DAQmx VIs

and functions

NI-DAQmx C Reference Help

Reference information for NI-DAQmx C functions and NI-DAQmx C properties

NI-DAQmx .NET Help Support for Visual Studio

Reference information for NI-DAQmx .NET methods and NI-DAQmx .NET

properties, key concepts, and a C enum to .NET enum mapping table

Test Equipment

The following table lists the equipment recommended for the performance verification and

adjustment procedures. If the recommended equipment is not available, select a substitute

using the requirements listed.

Table 1. Recommended Equipment

Equipment Recommended Model Requirements

Calibrator Fluke 5502A

Use a high-precision voltage source with gain error of

<500 ppm and offset error <50 μV.

Chassis NI cDAQ-9178 —

2| ni.com | NI 9228 Calibration Procedure

Test Conditions

The following setup and environmental conditions are required to ensure the device meets

published specifications.

• Keep connections to the device as short as possible. Long cables and wires act as

antennas, picking up extra noise that can affect measurements.

• Verify that all connections to the device are secure.

• Maintain an ambient temperature of 23 °C ± 5 °C. The device temperature will be greater

than the ambient temperature.

• Keep relative humidity below 80%.

• Allow a warm-up time of at least 15 minutes to ensure that the device measurement

circuitry is at a stable operating temperature.

Initial Setup

Complete the following steps to set up the NI 9228.

1. Install NI-DAQmx.

2. Make sure that the NI cDAQ-9178 power source is not connected to the chassis.

3. Connect the NI cDAQ-9178 chassis to the system safety ground.

a) Attach a ring lug to a 14 AWG (1.6 mm) wire.

b) Connect the ring lug to the ground terminal on the side of the NI cDAQ-9178 using

the ground screw.

c) Attach the other end of the wire to the system safety ground.

4. Install the module in slot 8 of the NI cDAQ-9178 chassis. Leave slots 1 through 7 of the

NI cDAQ-9178 chassis empty.

5. Connect the NI cDAQ-9178 chassis to your host computer.

6. Connect the power source to the NI cDAQ-9178 chassis.

7. Launch Measurement & Automation Explorer (MAX).

8. Right-click the device name and select Self-Test to ensure that the module is working

properly.

Verification

The following performance verification procedure describes the sequence of operation and

provides test points required to verify the NI 9228. The verification procedure assumes that

adequate traceable uncertainties are available for the calibration references.

Accuracy Verification

Complete the following procedure to determine the As-Found status of the NI 9228.

1. Set the calibrator to Standby mode (STBY).

NI 9228 Calibration Procedure | © National Instruments | 3

2. Connect the NI 9228 to the calibrator as shown in the following figure.

Figure 1. Accuracy Verification Connections

NI 9228

AI0–

Calibrator

AI0+

–

AI1–

AI1+

AI7–

AI7+

Note The chassis ground lug connection to ground is the NI 9228 ground

connection.

3. Set the calibrator voltage to a Test Point value indicated in the NI 9228 Verification Test

Limits table.

4. Set the calibrator to Operate mode (OPR).

5. Acquire and average samples for each channel.

a) Create and configure an AI voltage task according to the following NI 9228

Accuracy Verification Configuration table.

Table 2. NI 9228 Accuracy Verification Configuration

Minimum (V) Maximum (V) Scaled Units Physical Channels

Channel

Configuration

-60 60 Volts cDAQ1Mod8/AI0:AI7 Differential

b) Configure the task timing according to the following NI 9228 Timing Configuration

table.

Table 3. NI 9228 Timing Configuration

Sample Mode Samples Per Channel Rate (kS/s)

Finite Samples 100 1

c) Start the task.

d) Read the samples from the NI 9228.

e) Average the samples for each AI channel and record the average.

f) Stop and clear the task.

6. Set the calibrator to Standby mode (STBY).

7. Compare the averaged samples to the limits in the NI 9228 Verification Test Limits table

to verify the input accuracy. If the value is within these limits, the device passes the test.

8. Repeat steps 3 through 7 for each test point in the NI 9228 Verification Test Limits table.

9. Disconnect the calibrator from the device.

4| ni.com | NI 9228 Calibration Procedure

Table 4. NI 9228 Verification Test Limits

Test Points Device Under Test Settings/Configuration

Location Value Lower Limit (VDC) Upper Limit (VDC)

Positive full-scale 57.0 56.908 57.092

Mid 0 -0.006726 0.006726

Negative full-scale -57.0 -57.092 -56.908

Note The test limits listed in the NI 9228 Verification Test Limits table are derived

using values from the NI 9228 Accuracy Under Calibration Conditions table.

Adjustment

The following performance adjustment procedure describes the sequence of operation required

to adjust the NI 9228.

Accuracy Adjustment

Complete the following procedure to adjust the accuracy performance of the NI 9228.

1. Set the calibrator to Standby mode (STBY).

2. Connect the NI 9228 to the calibrator as shown in the Accuracy Verification section.

3. Adjust the NI 9228.

a) Initialize a calibration session on the NI 9228. The default password is NI.

b) Input the external temperature in degrees Celsius.

c) Call the NI 9228 get C Series adjustment points function to obtain an array of

recommended calibration voltages for the NI 9228.

d) Set the calibrator to a reference value determined by the array of recommended

calibration voltages.

e) Set the calibrator to Operate mode (OPR).

f) Call and configure the NI 9228 adjustment function according to NI 9228

Adjustment Configuration table.

Table 5. NI 9228 Adjustment Configuration

Physical Channel Reference Value

cDAQ1Mod8/AI0:7 A reference value from the array of adjustment points

g) Set the calibrator to Standby mode (STBY).

h) Repeat steps d through g for each point in the array.

i) Close the calibration session.

j) Close and commit the calibration session.

4. Disconnect the NI 9228 from the calibrator.

NI 9228 Calibration Procedure | © National Instruments | 5

EEPROM Update

When an adjustment procedure is completed, the NI 9228 internal calibration memory

(EEPROM) is immediately updated.

If you do not want to perform an adjustment, you can update the calibration date and onboard

calibration temperature without making any adjustments by initializing an external calibration,

setting the C Series calibration temperature, and closing the external calibration.

Reverification

Repeat the Verification section to determine the As-Left status of the device.

Note If any test fails Reverification after performing an adjustment, verify that you

have met the Test Conditions before returning your device to NI. Refer to the

Worldwide Support and Services section for assistance in returning the device to NI.

Accuracy under Calibration Conditions

The values in the following table are based on calibrated scaling coefficients, which are stored

in the onboard EEPROM.

The following accuracy table is valid for calibration under the following conditions:

• Ambient temperature 23 °C ± 5 °C

• NI 9228 installed in slot 8 of an NI cDAQ-9178 chassis

• Slots 1 through 7 of the NI cDAQ-9178 chassis are empty

Table 6. NI 9228 Accuracy under Calibration Conditions

Device Percent of Reading (Gain Error) Percentage of Range (Offset Error)1

NI 9228 0.149% 0.011%

Note For operational specifications, refer to the most recent NI 9228 Datasheet

online at ni.com/manuals.

Worldwide Support and Services

The NI website is your complete resource for technical support. At ni.com/support, you have

access to everything from troubleshooting and application development self-help resources to

email and phone assistance from NI Application Engineers.

Visit ni.com/services for information about the services NI offers.

1Range equals 63.8 V.

6| ni.com | NI 9228 Calibration Procedure

Visit ni.com/register to register your NI product. Product registration facilitates technical

support and ensures that you receive important information updates from NI.

A Declaration of Conformity (DoC) is our claim of compliance with the Council of the

European Communities using the manufacturer’s declaration of conformity. This system

affords the user protection for electromagnetic compatibility (EMC) and product safety. You

can obtain the DoC for your product by visiting ni.com/certification. If your product supports

calibration, you can obtain the calibration certificate for your product at ni.com/calibration.

NI corporate headquarters is located at 11500 North Mopac Expressway, Austin, Texas,

78759-3504. NI also has offices located around the world. For support in the United States,

create your service request at ni.com/support or dial 1 866 ASK MYNI (275 6964). For

support outside the United States, visit the Worldwide Offices section of ni.com/niglobal to

access the branch office websites, which provide up-to-date contact information.

NI 9228 Calibration Procedure | © National Instruments | 7

Information is subject to change without notice. Refer to the NI Trademarks and Logo Guidelines at ni.com/trademarks for

information on NI trademarks. Other product and company names mentioned herein are trademarks or trade names of their

respective companies. For patents covering NI products/technology, refer to the appropriate location: Help»Patents in your

software, the patents.txt file on your media, or the National Instruments Patent Notice at ni.com/patents. You can find

information about end-user license agreements (EULAs) and third-party legal notices in the readme file for your NI product. Refer

to the Export Compliance Information at ni.com/legal/export-compliance for the NI global trade compliance policy and how

to obtain relevant HTS codes, ECCNs, and other import/export data. NI MAKES NO EXPRESS OR IMPLIED WARRANTIES AS

TO THE ACCURACY OF THE INFORMATION CONTAINED HEREIN AND SHALL NOT BE LIABLE FOR ANY ERRORS. U.S.

Government Customers: The data contained in this manual was developed at private expense and is subject to the applicable

limited rights and restricted data rights as set forth in FAR 52.227-14, DFAR 252.227-7014, and DFAR 252.227-7015.

376505B-01 February 12, 2018

Inhaltsverzeichnis

Andere National Instruments E/A-System Handbücher

National Instruments

National Instruments Quadrature Input Module FP-QUAD-510 Bedienungsanleitung

National Instruments

National Instruments 9232 Handbuch

National Instruments

National Instruments Xmath Interactive Control Design Module ICDM Bedienungsanleitung

National Instruments

National Instruments USB-6221 OEM Bedienungsanleitung

National Instruments

National Instruments NI 9237E Series Bedienungsanleitung

National Instruments

National Instruments NI 9485 Bedienungsanleitung

National Instruments

National Instruments PCI-6251 Bedienungsanleitung

National Instruments

National Instruments NI 9269 Handbuch

National Instruments

National Instruments NI-9361 Bedienungsanleitung

National Instruments

National Instruments 9229 Bedienungsanleitung

National Instruments

National Instruments USB-9213 Bedienungsanleitung

National Instruments

National Instruments NI 9208E Bedienungsanleitung

National Instruments

National Instruments Interface Device NI PCI-1426 Bedienungsanleitung

National Instruments

National Instruments 9215E Bedienungsanleitung

National Instruments

National Instruments FOUNDATION Bedienungsanleitung

National Instruments

National Instruments 9361 Handbuch

National Instruments

National Instruments USB-6001 Bedienungsanleitung

National Instruments

National Instruments NI PCI-6510 Bedienungsanleitung

National Instruments

National Instruments 6527 Bedienungs- und Wartungshandbuch

National Instruments

National Instruments DAQCard-6533 Bedienungsanleitung

National Instruments

National Instruments PXIe-7856R Bedienungsanleitung

National Instruments

National Instruments PXI-7842 Bedienungsanleitung

National Instruments

National Instruments PXI-6070E Bedienungsanleitung

National Instruments

National Instruments NI 7831R Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung