National Instruments R Series Bedienungsanleitung

USER MANUAL

NI PXIe-7861

R Series Reconfigurable I/O Module (AI, AO, DIO) for PXI Express,

16 AI, 8 AO, 32 DIO, 1 MS/s AIO, 512 MB DRAM,

Kintex-7 160T FPGA

This document provides compliance, pinout, connectivity, mounting, and power information

for the NI PXIe-7861.

Hardware Overview

The following high-level block diagram represents the NI PXIe-7861.

Figure 1. NI PXIe-7861 Block Diagram

Device

Temperature

NI ASIC

Kintex-7

FPGA

Flash

Memory

DIO

Data/

Address/

Control

Overvoltage

Protection

+5 V

Reference

AO (x8)

DAC

ADC AI

AI (x8)

INA

DIO (x16)

DDR3 RAM 100 MHz

OSC

Overvoltage

Protection

Overvoltage

Protection

NI PXIe-7861

PXIe Connector

Overvoltage

Protection

+5 V

Reference

ADC

AI (x8)

INA

DIO (x16)

Overvoltage

Protection

DIO

(RMIO)

CONNECTOR 1

(RMIO)

CONNECTOR 0

Pinout

TERMINAL 34 TERMINAL 1

TERMINAL 35

TERMINAL 68 TERMINAL 68

TERMINAL 34 TERMINAL 1

TERMINAL 35

+5V

DIO0

DIO1

DIO2

DIO3

DIO4

DIO5

DIO6

DIO7

DIO9

DIO11

DIO13

DIO15

AO7

AO6

AO5

AO4

AO3

AO2

AO1

AO0

AISENSE0

AI7+

AIGND6

AI6+

AI5+

AIGND4

AI4+

AI3+

AIGND2

AI2+

AI1+

AIGND0

AI0+

+5V

DGND

DIO8

DIO10

DIO12

DIO14

AOGND7

AOGND6

AOGND5

AOGND4

AOGND3

AOGND2

AOGND1

AOGND0

AI7–

AIGND7

AI6–

AI5–

AIGND5

AI4–

AI3–

AIGND3

AI2–

AI1–

AIGND1

AI0–

68 34

67 33

66 32

65 31

64 30

63 29

62 28

61 27

60 26

59 25

58 24

57 23

56 22

55 21

54 20

53 19

52 18

51 17

50 16

49 15

48 14

47 13

46 12

45 11

44 10

43 9

42 8

41 7

40 6

39 5

38 4

37 3

36 2

35 1

CONNECTOR 0

(RMIO)

+5V

DIO0

DIO1

DIO2

DIO3

DIO4

DIO5

DIO6

DIO7

DIO9

DIO11

DIO13

DIO15

AISENSE1

AI15+

AIGND14

AI14+

AI13+

AIGND12

AI12+

AI11+

AIGND10

AI10+

AI9+

AIGND8

AI8+

+5V

DGND

DIO8

DIO10

DIO12

DIO14

AI15-

AIGND15

AI14-

AI13-

AIGND13

AI12-

AI11-

AIGND11

AI10-

AI9-

AIGND9

AI8-

68 34

67 33

66 32

65 31

64 30

63 29

62 28

61 27

60 26

59 25

58 24

57 23

56 22

55 21

54 20

53 19

52 18

51 17

50 16

49 15

48 14

47 13

46 12

45 11

44 10

43 9

42 8

41 7

40 6

39 5

38 4

37 3

36 2

35 1

CONNECTOR 1

(RMIO)

Table 1. NI PXIe-7861 Signal Descriptions

Signal Description

AI+ Positive analog input signal connection

AI- Negative analog input signal connection

2| ni.com | NI PXIe-7861 User Manual

Table 1. NI PXIe-7861 Signal Descriptions (Continued)

Signal Description

AISENSE Reference connection for NRSE measurements

AIGND Ground reference for the analog input signal

AO Analog output signal connection

AOGND Ground reference for the analog output signal

DIO Digital input/output signal connection

DGND Ground reference for the digital signal

GND Ground connection

Supply (+5 Vout) 5 V power output connection for external devices

NC No connection

The NI PXIe-7861 is protected from overvoltage and overcurrent conditions.

Note Refer to the NI PXIe-7861 Specifications, available at ni.com/manuals for

more information.

Note The pinout label on the lid of the SCB-68A accessory is incompatible with

the NI PXIe-7861. Refer to the NI 78xxR Pinout Labels for the SCB-68A, available

at ni.com/manuals for the compatible pinout labels.

Connectivity Options

Use the following connection accessories and cables to access the signals on the I/O

connectors.

Table 2. Connection Accessories and Cables

Connector Type Accessory Description NI Part Number

RMIO

NI SCB-68A Noise Rejecting, Shielded I/O

Connector Block 782536-01

NI SHC68-68-

RMIO

RMIO Shielded Cable, 68 pin D-

Type to 68 pin VHDCI (1 m) 189588-01

RMIO Shielded Cable, 68 pin D-

Type to 68 pin VHDCI (2 m) 189588-02

NI PXIe-7861 User Manual | © National Instruments | 3

Analog Input

The NI PXIe-7861 provides connections for 16 AI channels. Each channel has an AI+ pin, AI-

pin, and AIGND pin to which you can connect both single-ended or differential voltage

signals. Use the AISENSE pin to connect non-referenced single-ended signals.

Connecting Single-Ended Voltage Signals

To connect referenced single-ended voltage signals to the NI PXIe-7861, you must connect the

voltage ground signal to AI GND in order to keep the common-mode voltage in the specified

range.

Figure 2. Connecting Referenced Single-Ended Signals to the NI PXIe-7861

PGIA ADC

AI+

NI PXIe-7861

Connection

Accessory

AISENSE

AIGND

–

Overvoltage

Protection

AI– Overvoltage

Protection

Overvoltage

Protection

To connect non-referenced single-ended voltage signals to the NI PXIe-7861, you must

connect the voltage ground signal to AI SENSE in order to keep the common-mode voltage in

the specified range.

Figure 3. Connecting Non-Referenced Single-Ended Signals to the NI PXIe-7861

PGIA ADC

AI+

NI PXIe-7861

Connection

Accessory

AISENSE

AIGND

Vcm

–

Overvoltage

Protection

AI– Overvoltage

Protection

Overvoltage

Protection

4| ni.com | NI PXIe-7861 User Manual

Connecting Differential Voltage Signals

You can connect grounded or floating differential signal sources to the NI PXIe-7861. Connect

the positive voltage signal to the AI+ and the negative voltage signal to AI-. To connect

grounded differential signals to the NI PXIe-7861, you must also connect the signal reference

to AI GND.

Figure 4. Connecting Grounded Differential Signals to the NI PXIe-7861

PGIA ADC

AI+

NI PXIe-7861

Connection

Accessory

AISENSE

AIGND

Vcm

–

Overvoltage

Protection

AI– Overvoltage

Protection

Overvoltage

Protection

To connect floating differential signals to the NI PXIe-7861, you must connect the negative

and positive signals to AI GND through 1 MΩ resistors to keep the voltage within the

common-mode voltage range. If the voltage source is outside the common-mode voltage

range, the NI PXIe-7861 does not read data accurately.

Figure 5. Connecting Floating Differential Signals to the NI PXIe-7861

PGIA ADC

AI+

NI PXIe-7861

Connection

Accessory

AISENSE

AIGND

–

Overvoltage

Protection

AI– Overvoltage

Protection

Overvoltage

Protection

Analog Output

The NI PXIe-7861 provides connections for eight analog output channels. Each channel has an

AO pin and AOGND pin to which you can connect a load.

NI PXIe-7861 User Manual | © National Instruments | 5

Figure 6. Connecting a Load

NI PXIe-7861

Connection

Accessory

AOGND

LOAD

DAC

Digital I/O

The NI PXIe-7861 provides connections for 32 digital input/output (DIO) channels. Connector

0 and Connector 1 each contains 16 low-speed channels that can run up to 10 MHz signal

frequencies. Each connector has a fixed logic level of 3.3 V. You can configure each channel

as input or output.

Figure 7. Connecting to the DIO Channels

NI PXIe-7861

Power

FPGA

Connection

Accessory

DIO0

DIO1

DIO14

DIO15

Connecter 0 (RMIO)

Connection

Accessory

DIO0

DIO1

DIO14

DIO15

Connecter 1 (RMIO)

1. Low-speed signal frequencies up to 10 MHz with logic levels configured as 3.3 V.

2. LED

The DIO channels, which have overvoltage and undervoltage protection as well as over

current protection, connect to the FPGA . Refer to the device specifications on ni.com/manuals

for more information about the maximum voltage and current.

6| ni.com | NI PXIe-7861 User Manual

When the system powers on, the DIO channels are set as input low with pull-down resistors.

To set another power-on state, you can configure the NI PXIe-7861 to load a VI when the

system powers on. The VI can then set the DIO lines to any power-on state. Visit ni.com/info

and enter RSeries_PowerUpStates to learn more about configuring the power-up states

for the NI PXIe-7861.

All the DIO channels on each connector are routed with a 50 Ω characteristic trace impedance.

Route all external circuitry with a similar impedance to ensure best signal quality. NI

recommends performing signal integrity measurements to test the affect of signal routing with

the cable and connection accessory for your application.

Field Wiring Considerations

Environmental noise can seriously affect the measurement accuracy of the device if you do not

take proper care when running signal wire between signal sources and the device. The

following recommendations mainly apply to AI signal routing to the device, as well as signal

routing in general.

Take the following precautions to minimize noise pickup and maximize measurement

accuracy:

• Use differential AI connections to reject common-mode noise.

• Use individually shielded, twisted-pair wires to connect AI signals to the device. With

this type of wire, the signal attached to the positive and negative inputs are twisted

together and then covered with a shield. You then connect this shield only at one point to

the signal source ground. This kind of connection is required for signals traveling through

areas with large magnetic fields or high electromagnetic interference.

• Route signals to the device carefully. Keep cabling away from noise sources, such as

video monitors and analog signals.

Use the following recommendations for all signal connections to the NI PXIe-7861:

• Separate NI PXIe-7861 signal lines from high-current or high-voltage lines. These lines

can induce currents in or voltages on the NI PXIe-7861 signal lines if they run in parallel

paths at a close distance. To reduce the magnetic coupling between lines, separate them

by a reasonable distance if they run in parallel or run the lines at right angles to each

other.

• Do not run signal lines through conduits that also contain power lines.

• Protect signal lines from magnetic fields caused by electric motors, welding equipment,

breakers, or transformers by running them through special metal conduits.

+5 V Power Source

Use the +5 V terminals on the I/O connector supply +5 V referenced to DGND to power

external circuitry.

Caution Never connect the +5 V power terminals to analog or digital ground or

any other voltage source on the NI PXIe-7861 or any other device. Doing so can

damage the device and the computer. National Instruments is not liable for damage

resulting from such a connection.

The power rating is 4.75 to 5.1 V DC at 0.5 A per connector.

Worldwide Support and Services

The NI website is your complete resource for technical support. At ni.com/support, you have

access to everything from troubleshooting and application development self-help resources to

email and phone assistance from NI Application Engineers.

Visit ni.com/services for information about the services NI offers.

Visit ni.com/register to register your NI product. Product registration facilitates technical

support and ensures that you receive important information updates from NI.

A Declaration of Conformity (DoC) is our claim of compliance with the Council of the

European Communities using the manufacturer’s declaration of conformity. This system

affords the user protection for electromagnetic compatibility (EMC) and product safety. You

can obtain the DoC for your product by visiting ni.com/certification. If your product supports

calibration, you can obtain the calibration certificate for your product at ni.com/calibration.

NI corporate headquarters is located at 11500 North Mopac Expressway, Austin, Texas,

78759-3504. NI also has offices located around the world. For support in the United States,

create your service request at ni.com/support or dial 1 866 ASK MYNI (275 6964). For

support outside the United States, visit the Worldwide Offices section of ni.com/niglobal to

access the branch office websites, which provide up-to-date contact information.

Information is subject to change without notice. Refer to the NI Trademarks and Logo Guidelines at ni.com/trademarks for

information on NI trademarks. Other product and company names mentioned herein are trademarks or trade names of their

respective companies. For patents covering NI products/technology, refer to the appropriate location: Help»Patents in your

software, the patents.txt file on your media, or the National Instruments Patent Notice at ni.com/patents. You can find

information about end-user license agreements (EULAs) and third-party legal notices in the readme file for your NI product. Refer

to the Export Compliance Information at ni.com/legal/export-compliance for the NI global trade compliance policy and how

to obtain relevant HTS codes, ECCNs, and other import/export data. NI MAKES NO EXPRESS OR IMPLIED WARRANTIES AS

TO THE ACCURACY OF THE INFORMATION CONTAINED HEREIN AND SHALL NOT BE LIABLE FOR ANY ERRORS. U.S.

Government Customers: The data contained in this manual was developed at private expense and is subject to the applicable

limited rights and restricted data rights as set forth in FAR 52.227-14, DFAR 252.227-7014, and DFAR 252.227-7015.

378045A-03 March 13, 2018

Andere Handbücher für R Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere National Instruments E/A-System Handbücher

National Instruments

National Instruments SCXI-1126 Bedienungsanleitung

National Instruments

National Instruments NI 6738 Handbuch

National Instruments

National Instruments TBX-68 Bedienungsanleitung

National Instruments

National Instruments NI 6115/6120 Bedienungsanleitung

National Instruments

National Instruments NI 9411 Bedienungsanleitung

National Instruments

National Instruments NI 9222 Bedienungsanleitung

National Instruments

National Instruments NI 9219 Bedienungsanleitung

National Instruments

National Instruments PXIe-5764 Betriebsanleitung

National Instruments

National Instruments PXI-6238 Bedienungsanleitung

National Instruments

National Instruments USB-6525 Bedienungsanleitung

National Instruments

National Instruments 9232 Handbuch

National Instruments

National Instruments NI 9940 Bedienungsanleitung

National Instruments

National Instruments PC-DIO-96/PnP Bedienungsanleitung

National Instruments

National Instruments FIELDPOINT FP-PWM-520 Bedienungsanleitung

National Instruments

National Instruments PXI-6040E Bedienungsanleitung

National Instruments

National Instruments NI 9239 Bedienungsanleitung

National Instruments

National Instruments 9269E Bedienungsanleitung

National Instruments

National Instruments SCC-ACC01 Bedienungsanleitung

National Instruments

National Instruments 9220 Bedienungsanleitung

National Instruments

National Instruments NI 9231 Handbuch

National Instruments

National Instruments NI 9225 Bedienungsanleitung

National Instruments

National Instruments R Series Bedienungsanleitung

National Instruments

National Instruments NI 9437 Bedienungsanleitung

National Instruments

National Instruments sbRIO-9218 Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung