National Instruments Compact FieldPoint cFP-21 Series Bedienungsanleitung

Quick Start Guide

FieldPoint cFP-21xx

What You Need to Get Set Up

1. Mount the Compact FieldPoint Backplane

You can mount the cFP-BP-xbackplane on a 35mm DIN rail, on a panel, or in a

standard 19 in. rack. Before using any of these mounting methods, record the serial

number from the back of the backplane.

Each set of mounting instructions in this document includes an instruction to

connect the protective earth (PE) ground terminal on the cFP-BP-xbackplane to

the system safety ground. The backplane PE ground terminal has the following

•cFP-21xx LabVIEW RT controller

• Mounting hardware (DIN rail,

panel-mount, or rack-mount

accessory)

• I/O module(s)

•cFP-BP-xbackplane, connector

blocks, cables

• 11–30 VDC power supply

• Accessories: Ethernet cable,

number 2 Phillips screwdriver

• PC running Windows

• FieldPoint software 4.1.1 or later

• LabVIEW Real-Time Module

™

324033b.fm Page 1 Wednesday, September 14, 2005 2:09 PM

cFP-21xx Quick Start Guide 2 ni.com

symbol stamped beside it: . Connect the backplane PE ground terminal to the

system safety ground using 14 AWG (1.6 mm) wire with a ring lug. Use the

5/16 in. panhead screw shipped with the backplane to secure the ring lug to the

backplane PE ground terminal.

Caution Keep in mind these requirements for space and cabling

clearance:

• Allow at least 51 mm (2 in.) all around the backplane for air

circulation.

• Allow 38 mm (1.5 in.) below and 51 mm (2 in.) above the controller.

Cabling Clearance Cooling Outline 51 mm (2 in.) All Around

4 slots = 246 mm (9.68 in.)

8 slots = 441 mm (17.4 in.)

127 mm

(5.00 in.)

Min. 165 mm

(6.50 in.)

Cabling

Clearance

4 slots = 246 mm (9.68 in.)

8 slots = 441 mm (17.4 in.)

Cooling Outline 51 mm (2 in.) Cooling Outline 51 mm (2 in.)

Min. 182 mm (7.18 in.)

106 mm (4.18 in.)

324033b.fm Page 2 Wednesday, September 14, 2005 2:09 PM

Caution If you are using UL Recognized I\O modules with the Compact

FieldPoint system, you must install the entire system in a suitably rated,

UL Listed NEMA or IP enclosure.

Caution NI recommends that you use one of the mounting systems

described in this document. If you decide to use a custom mounting

solution, make sure that the screws you use are short enough to fit in the

holes in the backplane. The screw holes are 5 mm (0.2 in.) deep.

324033b.fm Page 3 Wednesday, September 14, 2005 2:09 PM

cFP-21xx Quick Start Guide 4 ni.com

Mounting the Backplane on a Panel

1. Fasten the panel-mount plates to the back of the cFP-BP-xusing a

number 2 Phillips screwdriver and the 8-32 ×5/16 in. countersink screws

shipped with the kit.

Caution Do not use screws longer than 5/16 in. to fasten the

panel-mount plates to the backplane.

NATIONAL

INSTRUMENTS

102 mm

(4 in.)

457 mm (18 in.)

324033b.fm Page 4 Wednesday, September 14, 2005 2:09 PM

104.78 mm

(4.1 in.)

63.50 mm

(2.5 in.)

22.23 mm

(0.9 in.)

33.15 mm

(1.3 in.)

129.54 mm

(5.1 in.)

311.40 mm

(12.3 in.)

387.60 mm

(15.3 in.)

407.80 mm

(16.1 in.)

127.00 mm

(5.0 in.)

440.94 mm

(17.4 in.)

260 mm (10.25 in.)

102 mm

(4 in.)

324033b.fm Page 5 Wednesday, September 14, 2005 2:09 PM

cFP-21xx Quick Start Guide 6 ni.com

2. Bolt or screw the panel-mount accessory to a panel.

3. Connect the PE ground terminal on the cFP-BP-xto safety ground.

Caution Disconnect power before removing the backplane from the

panel.

Mounting the Backplane on a DIN Rail

NI recommends DIN rail mounting for the cFP-BP-4 only. Use panel mounting or

rack mounting for the cFP-BP-8. The DIN rail mounting kit is NI part number

778614-01.

1. Fasten the DIN rail clip to the cFP-BP-4 using a number 2 Phillips screwdriver

and the 8-32 ×5/16 in. countersink screws shipped with the clip.

104.74 mm

(4.1 in.)

63.46 mm

(2.5 in.)

127.00 mm

(5.0 in.)

22.19 mm

(0.9 in.)

34.04 mm

(1.3 in.)

84.84 mm

(3.3 in.)

161.04 mm

(6.3 in.)

211.84 mm

(8.3 in.)

245.87 mm

(9.6 in.)

324033b.fm Page 6 Wednesday, September 14, 2005 2:09 PM

Caution Do not use screws longer than 5/16 in. to fasten the DIN rail

clip to the backplane.

2. Insert one edge of the DIN rail into the deeper opening of the DINrail clip.

3. Press down firmly on the backplane to compress the spring until the clip locks

in place on the DIN rail.

4. Connect the PE ground terminal on the cFP-BP-4 to safety ground.

Caution Disconnect power before removing the backplane from the

DIN rail.

NATIONAL

INSTRUMENTS

324033b.fm Page 7 Wednesday, September 14, 2005 2:09 PM

cFP-21xx Quick Start Guide 8 ni.com

Mounting the Backplane in a Standard 19 in. Rack

1. Fasten the rack-mount bracket to the back of the cFP-BP-xusing the captive

screws on the bracket.

2. Bolt the rack-mount accessory to a standard 19 in. rack.

NATIONAL

INSTRUMENTS

324033b.fm Page 8 Wednesday, September 14, 2005 2:09 PM

3. Connect the PE ground terminal on the cFP-BP-xto safety ground.

Caution Disconnect power before removing the backplane from the

DIN rail.

TIONAL

INSTRUMENTS

324033b.fm Page 9 Wednesday, September 14, 2005 2:09 PM

cFP-21xx Quick Start Guide 10 ni.com

2. Install the cFP-21xx Controller on the Backplane

1. Make sure that no power is connected to the controller.

2. Make sure that the cFP-21xx controller is right side up with the NI logo at the

top, and align the captive screws on the controller with the holes on the

backplane.

3. Seat the card edge at the back of the controller in the card-edge connector on

the backplane.

4. Press the controller firmly to seat it on the backplane.

5. Using a number 2 Phillips screwdriver with a shank of at least 64 mm (2.5 in.)

length, tighten the captive screws to 1.1 N · m (10 lb · in.) of torque.

TIONAL

INSTRUMENTS

324033b.fm Page 10 Wednesday, September 14, 2005 2:09 PM

Andere Handbücher für Compact FieldPoint cFP-21 Series

Inhaltsverzeichnis

Andere National Instruments Netzwerk-Hardware Handbücher

National Instruments

National Instruments GPIB-120A Bedienungsanleitung

National Instruments

National Instruments FIELDPOINT cFP-PWM-520 Bedienungsanleitung

National Instruments

National Instruments 6023E Bedienungsanleitung

National Instruments

National Instruments NI 447 Series Bedienungsanleitung

National Instruments

National Instruments DAQ 6527 Bedienungsanleitung

National Instruments

National Instruments DAQ SCXI-1161 Bedienungsanleitung

National Instruments

National Instruments 2806 Bedienungsanleitung

National Instruments

National Instruments NI WLS/ENET-9163 Bedienungsanleitung

National Instruments

National Instruments Fieldbus Bedienungsanleitung

National Instruments

National Instruments ISM-7413 Bedienungsanleitung

National Instruments

National Instruments NI ELVIS III Bedienungsanleitung

National Instruments

National Instruments NI 9149 Bedienungsanleitung

National Instruments

National Instruments NI Vision CVS-1450 Series Bedienungsanleitung

National Instruments

National Instruments IMAQ PCI-1411 Bedienungsanleitung

National Instruments

National Instruments PC-DIO-96 Bedienungsanleitung

National Instruments

National Instruments SCXI-1163 Bedienungsanleitung

National Instruments

National Instruments FIELDPOINT cFP-DO-403 Bedienungsanleitung

National Instruments

National Instruments GPIB GPIB-ENET/100 Bedienungsanleitung

National Instruments

National Instruments SCXI-1121 Bedienungsanleitung

National Instruments

National Instruments R Series Bedienungsanleitung

National Instruments

National Instruments WSN-3226 Bedienungsanleitung

National Instruments

National Instruments AT-232/2 Bedienungsanleitung

National Instruments

National Instruments NI-488.2 Bedienungsanleitung

National Instruments

National Instruments NI WAP-3701 Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung