National Instruments 9403 Bedienungsanleitung

GETTING STARTED GUIDE

NI 9403

32 DIO, 5 V/TTL, Bidirectional, 7 μs

This document explains how to connect to the NI 9403.

Note Before you begin, complete the software and

hardware installation procedures in your chassis

documentation.

Note The guidelines in this document are specific to

the NI 9403. The other components in the system might

not meet the same safety ratings. Refer to the

documentation for each component in the system to

determine the safety and EMC ratings for the entire

system.

Safety Guidelines

Operate the NI 9403 only as described in this document.

Caution Do not operate the NI 9403 in a manner not

specified in this document. Product misuse can result in

a hazard. You can compromise the safety protection

built into the product if the product is damaged in any

way. If the product is damaged, return it to NI for

repair.

2| ni.com | NI 9403 Getting Started Guide

Safety Voltages

Connect only voltages that are within the following limits:

Channel-to-COM ±30 V maximum on up to

8 channels at a time,

Measurement Category I

Isolation

Channel-to-channel None

Channel-to-earth ground

Continuous 60 VDC, Measurement

Category I

Withstand

up to 3,000 m altitude 1,000 Vrms, verified by a 5 s

dielectric withstand test

up to 5,000 m altitude 860 Vrms, verified by a 5 s

dielectric withstand test

Measurement Category I is for measurements performed on

circuits not directly connected to the electrical distribution system

referred to as MAINS voltage. MAINS is a hazardous live

NI 9403 Getting Started Guide | © National Instruments | 3

electrical supply system that powers equipment. This category is

for measurements of voltages from specially protected secondary

circuits. Such voltage measurements include signal levels, special

equipment, limited-energy parts of equipment, circuits powered

by regulated low-voltage sources, and electronics.

Caution Do not connect the NI 9403 to signals or use

for measurements within Measurement Categories II,

III, or IV.

Safety Guidelines for Hazardous Locations

The NI 9403 is suitable for use in Class I, Division 2, Groups A,

B, C, D, T4 hazardous locations; Class I, Zone 2, AEx nA IIC T4

and Ex nA IIC T4 hazardous locations; and nonhazardous

locations only. Follow these guidelines if you are installing the

NI 9403 in a potentially explosive environment. Not following

these guidelines may result in serious injury or death.

Caution Do not disconnect I/O-side wires or

connectors unless power has been switched off or the

area is known to be nonhazardous.

4| ni.com | NI 9403 Getting Started Guide

Caution Do not remove modules unless power has

been switched off or the area is known to be

nonhazardous.

Caution Substitution of components may impair

suitability for Class I, Division 2.

Caution For Division 2 and Zone 2 applications,

install the system in an enclosure rated to at least IP54

as defined by IEC/EN 60079-15.

Caution For Division 2 and Zone 2 applications,

connected signals must be within the following limits.

Capacitance 0.02 μF max

Special Conditions for Hazardous Locations Use in

Europe and Internationally

The NI 9403 has been evaluated as Ex nA IIC T4 Gc equipment

under DEMKO Certificate No. 07 ATEX 0626664X and is

IECEx UL 14.0089X certified. Each NI 9403 is marked II 3G

and is suitable for use in Zone 2 hazardous locations, in ambient

temperatures of -40 °C ≤ Ta ≤ 70 °C. If you are using the NI 9403

in Gas Group IIC hazardous locations, you must use the device in

NI 9403 Getting Started Guide | © National Instruments | 5

an NI chassis that has been evaluated as Ex nC IIC T4, Ex IIC

T4, Ex nA IIC T4, or Ex nL IIC T4 equipment.

Caution You must make sure that transient

disturbances do not exceed 140% of the rated voltage.

Caution The system shall only be used in an area of

not more than Pollution Degree 2, as defined in

IEC 60664-1.

Caution The system shall be mounted in an

ATEX/IECEx-certified enclosure with a minimum

ingress protection rating of at least IP54 as defined in

IEC/EN 60079-15.

Caution The enclosure must have a door or cover

accessible only by the use of a tool.

Electromagnetic Compatibility Guidelines

This product was tested and complies with the regulatory

requirements and limits for electromagnetic compatibility (EMC)

stated in the product specifications. These requirements and

limits provide reasonable protection against harmful interference

6| ni.com | NI 9403 Getting Started Guide

when the product is operated in the intended operational

electromagnetic environment.

This product is intended for use in industrial locations. However,

harmful interference may occur in some installations, when the

product is connected to a peripheral device or test object, or if the

product is used in residential or commercial areas. To minimize

interference with radio and television reception and prevent

unacceptable performance degradation, install and use this

product in strict accordance with the instructions in the product

documentation.

Furthermore, any changes or modifications to the product not

expressly approved by National Instruments could void your

authority to operate it under your local regulatory rules.

Special Conditions for Marine Applications

Some products are Lloyd’s Register (LR) Type Approved for

marine (shipboard) applications. To verify Lloyd’s Register

certification for a product, visit ni.com/certification and search

for the LR certificate, or look for the Lloyd’s Register mark on

the product.

NI 9403 Getting Started Guide | © National Instruments | 7

Caution In order to meet the EMC requirements for

marine applications, install the product in a shielded

enclosure with shielded and/or filtered power and

input/output ports. In addition, take precautions when

designing, selecting, and installing measurement probes

and cables to ensure that the desired EMC performance

is attained.

Preparing the Environment

Ensure that the environment in which you are using the NI 9403

meets the following specifications.

Operating temperature

(IEC 60068-2-1, IEC 60068-2-2)

-40 °C to 70 °C

Operating humidity

(IEC 60068-2-78)

10% RH to 90% RH,

noncondensing

Pollution Degree 2

Maximum altitude 5,000 m

Indoor use only.

8| ni.com | NI 9403 Getting Started Guide

Note Refer to the device datasheet on ni.com/manuals

for complete specifications.

Connecting the NI 9403

The NI 9403 provides connections for 32 digital input/output

channels.

NI 9403 Getting Started Guide | © National Instruments | 9

Figure 1. NI 9403 Pinout

DIO16

DIO17

DIO18

DIO19

DIO20

DIO21

DIO22

DIO23

COM

DIO24

DIO25

DIO26

DIO27

DIO28

DIO29

DIO30

DIO31

DIO0

DIO1

DIO2

DIO3

DIO4

DIO5

DIO6

DIO7

COM

DIO8

DIO9

DIO10

DIO11

DIO12

DIO13

DIO14

DIO15

RSVD

10 | ni.com | NI 9403 Getting Started Guide

Inhaltsverzeichnis

Andere National Instruments Aufnahmegeräte Handbücher

National Instruments

National Instruments NI VISION PCI-8254R Bedienungsanleitung

National Instruments

National Instruments VXI-USB Bedienungsanleitung

National Instruments

National Instruments GPIB-SCSI-A Bedienungsanleitung

National Instruments

National Instruments NI-9862 Bedienungsanleitung

National Instruments

National Instruments VXI-AT2022 Bedienungsanleitung

National Instruments

National Instruments PCIe-8253 Bedienungsanleitung

National Instruments

National Instruments PXIe-8240 Bedienungsanleitung

National Instruments

National Instruments PXI-PCI 8330 Series Bedienungsanleitung

National Instruments

National Instruments PCMCIA-232 Bedienungsanleitung

National Instruments

National Instruments NI-845 Series Bedienungsanleitung

National Instruments

National Instruments VXI-SB2020 Bedienungsanleitung

National Instruments

National Instruments PCI-8331 Bedienungsanleitung

National Instruments

National Instruments GPIB-COM Bedienungsanleitung

National Instruments

National Instruments VXI-AT2023 Bedienungsanleitung

National Instruments

National Instruments TPC-22 series Bedienungsanleitung

National Instruments

National Instruments AT-DIO-32F Bedienungsanleitung

National Instruments

National Instruments PCI-GPIB Bedienungsanleitung

National Instruments

National Instruments ENET-232 Series Bedienungsanleitung

National Instruments

National Instruments VME-SB2020 Bedienungsanleitung

National Instruments

National Instruments UMI-7774 Bedienungsanleitung

National Instruments

National Instruments 6527 Bedienungsanleitung

National Instruments

National Instruments GPIB-MAC Bedienungsanleitung

National Instruments

National Instruments MXI-Express x1 Series Bedienungsanleitung

National Instruments

National Instruments PXI-8461/2 Bedienungsanleitung

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch