National Instruments TPC-22 series Bedienungsanleitung

Getting Started with the

TPC-22xx

This guide includes setup instructions and specifications for the TPC-22xx

Human Machine Interface (HMI).

General Information

Introduction

The TPC-22xx touch panel computer, an HMI based on an x86 platform,

includes these key features:

•Powerful processing—The TPC-22xx uses the Intel Atom processor,

specifically designed for embedded, industrial applications.

•Fanless—By using an advanced but low-power Intel Atom processor,

the TPC-22xx does not require a fan for cooling.

•Robust communication—The TPC-22xx is a powerful I/O interface

for easy communication with other devices. The I/O interface includes

serial ports, gigabit Ethernet, and USB 2.0 support.

•Wide operating temperature and isolation protection—The

TPC-22xx provides a –20 to 60 °C operating temperature range and

complete isolation protection for the serial ports.

•Windows Embedded support—The TPC-22xx supports the latest

embedded Windows operating systems from Microsoft.

I/O Ports

The TPC-22xx includes the following ports:

• Two serial ports: RS232 (COM1) and RS422/485 (COM2)

• Two USB 2.0 ports compliant with USB 1.0 and 1.1

• Two RJ-45 Gigabit Ethernet ports

Getting Started with the TPC-22xx 2 ni.com

Figure 1 shows the I/O port arrangement.

Figure 1. I/O Port Arrangement

For more TPC-22xx specifications, refer to the Specifications section.

System Setup

Important Safety Information

Before setting up the TPC-22xx, read these safety instructions carefully.

Disconnect this equipment from any AC outlet before cleaning. Use a damp

cloth. Do not use liquid or spray detergents for cleaning.

For plug-in equipment, the power outlet socket must be located near the

equipment and must be easily accessible.

Keep this equipment away from excessive humidity.

Place this equipment on a reliable surface during installation. Dropping it

or letting it fall may cause damage.

The openings on the enclosure are for air convection and protect the

equipment from overheating. Do not cover the openings.

Make sure the power source voltage is correct before connecting the

equipment to the power outlet.

Position the power cord so that it cannot be stepped on. Do not place

anything over the power cord.

All cautions and warnings on the equipment should be noted.

If the equipment is not used for a long time, disconnect it from the power

source to avoid damage by transient overvoltage.

1LAN1

2LAN2

3USB

4 COM2 (RS422/485)

5 COM1 (RS232)

1 2 345

©National Instruments Corporation 3 Getting Started with the TPC-22xx

Never pour any liquid into an opening. This may cause fire or electrical

shock.

Never open the equipment. For safety reasons, only qualified service

personnel should open the equipment.

If one of the following situations arises, have service personnel check the

equipment:

• The power cord or plug is damaged.

• Liquid has penetrated into the equipment.

• The equipment has been exposed to moisture.

• The equipment does not work well, or you cannot get it to work

according to the user manual.

• The equipment has been dropped and damaged.

• The equipment has obvious signs of breakage.

Do not leave this equipment in an environment where the storage

temperature may go below –20 °C (–4 °F) or above 60 °C (140 °F). Doing

so could damage the equipment. The equipment should be in a controlled

environment.

Caution There is a danger of explosion if the battery is incorrectly replaced. Replace the

battery only with the same or equivalent type recommended by the manufacturer. Discard

used batteries according to the manufacturer’s instructions.

The sound pressure level at the operator’s position according to

IEC 704-1:1982 is no more than 70 dB (A).

Caution The protection this equipment provides may be impaired if it is used in a manner

not described in this manual.

Setup

Follow these steps to set up the TPC-22xx:

1. Unpack the TPC-22xx. Be sure your kit includes the following items:

• The TPC-22xx HMI

• Panel mounting clamps

• Panel mounting screws

• One 3-pin power connector

• One HMI Resource CD

• One earth ground cable

If any items are missing or damaged, contact National Instruments.

Getting Started with the TPC-22xx 4 ni.com

Caution Be sure system power is off before plugging in or pulling out the CompactFlash

card.

2. Verify that the CompactFlash card containing Windows Embedded or

another operating system is installed in the unit.

3. Connect the power connector to an 18–32 VDC power line. Be sure to

connect the positive, negative, and ground lines as shown in Figure 2.

The power lines can be from either a power adapter or in-house power

source.

Figure 2. Power Connector

4. Connect the power connector to the power receptor on the TPC-22xx.

The power receptor pin assignment is shown in Figure 3.

Figure 3. Power Receptor and Pin Assignment

5. The system powers on immediately after you apply power.

+–GND

GND

–+

©National Instruments Corporation 5 Getting Started with the TPC-22xx

Specifications

For complete specifications, including physical dimensions, refer to the

user manual for your TPC-22xx at ni.com/manuals. You can use this

web page to search for the user manual by model name, such as TPC-2206.

System

CPU........................................................ Intel Atom Processor Z520PT

1.33 GHz w/HyperThreading

SCH........................................................ Intel System Controller Hub

US15WPT

Video...................................................... Intel GMA 500

BIOS....................................................... Award 4 Mbit flash

Ethernet .................................................. Realtek RTL8168C(P) ×2;

10/100/1000, IEEE 802.3ab

protocol compatible

RAM....................................................... 1 GB DDR2

Watchdog timer...................................... SCH3114X1 watchdog timer;

1~255 s timeout period

CompactFlash......................................... Ultra ATA/100, UDMA/100

compatible, 4 GB minimum

Touchscreen

Touch type.............................................. Resistive

Base glass construction .......................... Tempered glass

Light transmission.................................. 80% ± 3%

Controller ............................................... RS-232 interface (COM3)

Lifespan.................................................. 1 million touches at a single point

Getting Started with the TPC-22xx 6 ni.com

Power

Input voltage ...........................................18–32 VDC

Note Providing power levels either below or above the stated range is not recommended.

Note For your protection, the fuse is set to break if the input voltage exceeds 33 VDC.

Environment

Operating temperature ............................–20 to 60 °C (–4 to 140 °F)

Storage temperature ................................–20 to 60 °C (–4 to 140 °F)

Humidity.................................................40 °C @ 10 to 95% relative

humidity (noncondensing)

Vibration.................................................2 grms (5 to 500 Hz)

Maximum altitude...................................2,000 m

Pollution Degree .....................................2

Indoor use only.

Note The front bezel is compliant with NEMA4 and IP65.

Safety

This product is designed to meet the requirements of the following

standards of safety for information technology equipment:

• IEC 60950-1, EN 60950-1

• UL 60950-1, CSA 60950-1

Note For UL and other safety certifications, refer to the product label or the Online

Product Certification section.

Electromagnetic Compatibility

This product meets the requirements of the following EMC standards for

information technology equipment:

• EN 55024 (CISPR 24); Immunity

• EN 55022 (CISPR 22); Class A Emissions

• EN 55011 (CISPR 11); Class A Emissions

• AS/NZS CISPR 11; Class A Emissions

• AS/NZS CISPR 22; Class A Emissions

©National Instruments Corporation 7 Getting Started with the TPC-22xx

• FCC 47 CFR Part 15B: Class A Emissions

• ICES-003: Class A Emissions

Note In the United States (per FCC 47 CFR), Class A equipment is intended for use in

commercial, light-industrial, and heavy-industrial locations. In Europe, Canada, Australia

and New Zealand (per CISPR 11) Class A equipment is intended for use only in

heavy-industrial locations.

Note Group 1 equipment (per CISPR 11) is any industrial, scientific, or medical

equipment that does not intentionally generate radio frequency energy for the treatment of

material or inspection/analysis purposes.

Note For the standards applied to assess the EMC of this product, refer to the Online

Product Certification section.

CE Compliance

This product meets the essential requirements of applicable European

Directives as follows:

• 2006/95/EC; Low-Voltage Directive (safety)

• 2004/108/EC; Electromagnetic Compatibility Directive (EMC)

Online Product Certification

Refer to the product Declaration of Conformity (DoC) for additional

regulatory compliance information. To obtain product certifications and

the DoC for this product, visit ni.com/certification, search by model

number or product line, and click the appropriate link in the Certification

column.

Environmental Management

National Instruments is committed to designing and manufacturing

products in an environmentally responsible manner. NI recognizes that

eliminating certain hazardous substances from our products is beneficial to

the environment and to NI customers.

For additional environmental information, refer to the NI and the

Environment Web page at ni.com/environment. This page contains the

environmental regulations and directives with which NI complies, as well

as other environmental information not included in this document.

LabVIEW, National Instruments, NI, ni.com, the National Instruments corporate logo, and the Eagle

logo are trademarks of National Instruments Corporation. Refer to the Trademark Information at

ni.com/trademarks for other National Instruments trademarks. Other product and company

names mentioned herein are trademarks or trade names of their respective companies. For patents

covering National Instruments products/technology, refer to the appropriate location: Help»Patents

in your software, the patents.txt file on your media, or the National Instruments Patent Notice

at ni.com/patents.

Waste Electrical and Electronic Equipment (WEEE)

EU Customers At the end of the product life cycle, all products must be sent to a WEEE

recycling center. For more information about WEEE recycling centers, National

Instruments WEEE initiatives, and compliance with WEEE Directive 2002/96/EC on

Waste and Electronic Equipment, visit ni.com/environment/weee.

Mercury Disposal and Recycling

LCD lamp(s) in this monitor contain mercury. Dispose or recycle

according to local, state or federal laws. Consult the Electronic Industries

Alliance at www.eiae.org for more information. For specific information

on lamp disposal, consult www.lamprecycle.org.

Cleaning

If you need to clean the unit, use a soft, nonmetallic brush. Make sure that

the unit is completely dry and free from contaminants before returning it to

service.

⬉ᄤֵᙃѻક∵ᶧ᥻ࠊㅵ⧚ࡲ⊩ ˄Ё೑

RoHS

Ё೑ᅶ᠋ National Instruments ヺড়Ё೑⬉ᄤֵᙃѻકЁ䰤ࠊՓ⫼ᶤѯ᳝ᆇ⠽䋼ᣛҸ (RoHS)Ǆ

݇Ѣ National Instruments Ё೑ RoHS ড়㾘ᗻֵᙃˈ䇋ⱏᔩ ni.com/environment/rohs_chinaǄ

(For information about China RoHS compliance, go to ni.com/environment/rohs_china.)

Inhaltsverzeichnis

Andere National Instruments Aufnahmegeräte Handbücher

National Instruments

National Instruments VXI-USB Bedienungsanleitung

National Instruments

National Instruments PXIe-416 Series Bedienungsanleitung

National Instruments

National Instruments NI PCIe-8233 Bedienungsanleitung

National Instruments

National Instruments VME-SB2020 Bedienungsanleitung

National Instruments

National Instruments USB-8502 Bedienungsanleitung

National Instruments

National Instruments NI-9862 Bedienungsanleitung

National Instruments

National Instruments AT-DIO-32F Bedienungsanleitung

National Instruments

National Instruments PCMCIA-232 Bedienungsanleitung

National Instruments

National Instruments NI VISION PCI-8254R Bedienungsanleitung

National Instruments

National Instruments MXI-Express x1 Series Bedienungsanleitung

National Instruments

National Instruments VXI-AT2022 Bedienungsanleitung

National Instruments

National Instruments MXI-2 Bedienungsanleitung

National Instruments

National Instruments 8234 Bedienungsanleitung

National Instruments

National Instruments FieldPoint FP-1000 Bedienungsanleitung

National Instruments

National Instruments PCI-GPIB Bedienungsanleitung

National Instruments

National Instruments PCI-8331 Bedienungsanleitung

National Instruments

National Instruments PXI-PCI 8330 Series Bedienungsanleitung

National Instruments

National Instruments NI 9866 Bedienungsanleitung

National Instruments

National Instruments VXI-MXI-Express Series Bedienungsanleitung

National Instruments

National Instruments NI 9403 Bedienungsanleitung

National Instruments

National Instruments MXI VXI-PCI8026 Bedienungsanleitung

National Instruments

National Instruments FieldPoint FP-1000 Kurzanleitung

National Instruments

National Instruments GPIB-USB Series Montageanleitung

National Instruments

National Instruments Gigabit Ethernet (GigE) Interface Device NI... Bedienungsanleitung

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch