National Instruments PXIe-416 Series Bedienungsanleitung

USER GUIDE

PXIe-416x Noise Filter

Accessory

Noise Filter Accessory for the PXIe-4162/PXIe-4163

This document explains how to install and use the PXIe-416x Noise Filter Accessory with a

PXIe-4162/PXIe-4163 source measure unit (SMU)—collectively referred to as the PXIe-416x

—and includes PXIe-416x Noise Filter Accessory specifications.

Read this document and the documents listed in the Additional Resources section about

installation, configuration, and operation of this product before you install, configure, operate,

or maintain this product. Users are required to familiarize themselves with installation and

wiring instructions in addition to requirements of all applicable codes, laws, and standards.

The PXIe-416x Noise Filter Accessory is used to modify the behavior of the

PXIe-4162/PXIe-4163 SMU when the module is used in remote sense mode.

Caution Observe all instructions and cautions in the user documentation. Using

the product in a manner not specified can damage the product and compromise the

built-in safety protection.

Attention Suivez toutes les instructions et respectez toutes les mises en garde de la

documentation d'utilisation. L'utilisation du produit de toute autre façon que celle

spécifiée risque de l'endommager et de compromettre la protection de sécurité

intégrée.

Notice This device is intended for use only with the PXIe-4162/PXIe-4163 SMU.

For more information about the PXIe-4162/PXIe-4163, refer to ni.com/manuals.

Contents

Icons.......................................................................................................................................... 2

Getting Started with the PXIe-4162/4163 Noise Filter Accessory........................................... 2

Kit Contents and Other Equipment...................................................................................2

Installing the PXIe-416x Noise Filter Accessory............................................................. 2

PXIe-416x Noise Filter Accessory Specifications....................................................................5

Definitions.........................................................................................................................6

Derating.............................................................................................................................6

Physical............................................................................................................................. 6

Environmental Guidelines.................................................................................................6

Compliance and Standards................................................................................................7

Additional Resources................................................................................................................ 8

NI Services................................................................................................................................9

Icons

Notice Take precautions to avoid data loss, loss of signal integrity, degradation of

performance, or damage to the model.

Caution Take precautions to avoid injury. Consult the model documentation for

cautionary statements when you see this icon printed on the model. Cautionary

statements are localized into French for compliance with Canadian requirements.

Getting Started with the PXIe-4162/4163 Noise

Filter Accessory

Kit Contents and Other Equipment

Your kit includes an assembled PXIe-416x Noise Filter Accessory. In addition, you will need

the following items not included in your PXIe-416x Noise Filter Accessory kit to install and

use the PXIe-416x Noise Filter Accessory.

• PXIe-4162/PXIe-41631

• Number 1 Phillips-head screwdriver

Visit ni.com for more information about the PXIe-4162/PXIe-4163.

Installing the PXIe-416xNoise Filter Accessory

Complete the following steps to install the PXIe-416x Noise Filter Accessory with a

PXIe-416x.

Before you begin, install the PXIe-416x in a chassis and ensure that all signals are

disconnected from the PXIe-416x if you have not already done so. Refer to the getting started

guide for your module at ni.com/manuals for installation instructions.

1. Connect the PXIe-416x Noise Filter Accessory to the PXIe-416x.

a) Align the male D-SUB connector on the PXIe-416x Noise Filter Accessory and the

female D-SUB connector on the front of the PXIe-416x and attach.

b) Tighten the screws on the front of the PXIe-416x Noise Filter Accessory until the

accessory is secured to the PXIe-416x. Tighten to a maximum torque of 3.6 lb · in.

(0.407 N · m).

1If you use the PXIe-416x Noise Filter Accessory with a PXIe-4162/PXIe-4163, refer to your

module specifications at ni.com/manuals for pinout and signal information during installation.

2| ni.com | PXIe-416x Noise Filter Accessory User Guide

Figure 1. Installed PXIe-416xNoise Filter Accessory

2. Connect a compatible cable or connectivity accessory to the PXIe-416x Noise Filter

Accessory. Refer to your cable or accessory documentation for more information.

Refer to the following pinouts for your respective module to make the appropriate connections

for your application.

PXIe-416x Noise Filter Accessory User Guide | © National Instruments Corporation | 3

Figure 2. PXIe-4162 Pinout

CH1 Output HI

CH1 Sense HI

CH10 Sense LO

Calibration HI

CH10 Sense HI

CH10 Guard

CH10 Output HI

CH7 Guard

CH7 Sense LO

CH7 Output HI

CH7 Sense HI

CH0 to 11 Output LO

CH4 Guard

CH4 Sense LO

CH4 Output HI

CH4 Sense HI

CH1 Sense LO

CH1 Guard

CH0 Output HI

CH0 Sense HI

CH2 Guard

CH2 Sense LO

CH3 Output HI

CH3 Sense HI

CH5 Guard

CH5 Sense LO

CH6 Output HI

CH6 Sense HI

CH8 Guard

CH8 Sense LO

CH9 Output HI

CH9 Sense HI

CH11 Guard

CH11 Sense LO

CH0 Guard

CH0 Sense LO

CH2 Output HI

CH2 Sense HI

CH3 Guard

CH3 Sense LO

CH5 Output HI

CH5 Sense HI

CH6 Guard

CH6 Sense LO

CH8 Output HI

CH8 Sense HI

CH9 Guard

CH9 Sense LO

CH11 Output HI

CH11 Sense HI

4| ni.com | PXIe-416x Noise Filter Accessory User Guide

Figure 3. PXIe-4163 Pinout

CH2 Output HI

CH2 Sense HI

CH21 Sense HI

Calibration HI

CH20 Sense HI

CH21 Output HI

CH20 Output HI

CH15 Output HI

CH15 Sense HI

CH14 Output HI

CH14 Sense HI

CH0-23 Output LO

CH9 Output HI

CH9 Sense HI

CH8 Output HI

CH8 Sense HI

CH3 Sense HI

CH3 Output HI

CH0 Output HI

CH0 Sense HI

CH5 Output HI

CH5 Sense HI

CH6 Output HI

CH6 Sense HI

CH11 Output HI

CH11 Sense HI

CH12 Output HI

CH12 Sense HI

CH17 Output HI

CH17 Sense HI

CH18 Output HI

CH18 Sense HI

CH23 Output HI

CH23 Sense HI

CH1 Output HI

CH1 Sense HI

CH0-5 Sense LO

CH4 Output HI

CH4 Sense HI

CH7 Output HI

CH7 Sense HI

CH6-11 Sense LO

CH10 Output HI

CH10 Sense HI

CH13 Output HI

CH13 Sense HI

CH12-17 Sense LO

CH16 Output HI

CH16 Sense HI

CH19 Output HI

CH19 Sense HI

CH18-23 Sense LO

CH22 Output HI

CH22 Sense HI

Uninstalling the PXIe-416x Noise Filter Accessory

1. Disconnect any attached cable or connectivity accessory from the PXIe-416x Noise Filter

Accessory.

2. Loosen the screws on the front of the PXIe-416x Noise Filter Accessory and detach the

accessory from the front of the PXIe-416x.

PXIe-416xNoise Filter Accessory Specifications

These specifications apply to the PXIe-416x Noise Filter Accessory for use with the

PXIe-4162/PXIe-4163.

The PXIe-4162 is a 12-Channel, ±24 V, 100 mA SMU, and the PXIe-4163 is a

24-Channel, ±24 V, 50 mA SMU. Refer to the module specifications at ni.com/manuals for

more information.

PXIe-416x Noise Filter Accessory User Guide | © National Instruments Corporation | 5

Definitions

Warranted specifications describe the performance of a model under stated operating

conditions and are covered by the model warranty.

Characteristics describe values that are relevant to the use of the model under stated operating

conditions but are not covered by the model warranty.

•Typical specifications describe the performance met by a majority of models.

•Nominal specifications describe an attribute that is based on design, conformance testing,

or supplemental testing.

Specifications are Nominal unless otherwise noted.

Derating

Remote Sense

Maximum sense lead resistance 100 Ω

Maximum force lead drop 1 V

Voltage accuracy Add 200 μV to the accuracy specification for

your respective module when using the

PXIe-416x Noise Filter Accessory.

Noise filter cutoff frequency 5 MHz

Load Regulation

Voltage Add 300 μV/mA to the accuracy specification

for your respective module at the output

connector pins of the connected PXIe-416x

Noise Filter Accessory when using local sense

configuration.

Physical

Dimensions 8 mm × 72 mm × 16 mm

(2.9 in. × 2.8 in. × 0.6 in.)

Weight 89 g (3.15 oz)

Environmental Guidelines

Notice This model is intended for use in indoor applications only.

6| ni.com | PXIe-416x Noise Filter Accessory User Guide

Environmental Characteristics

Temperature and Humidity

Temperature

Operating

Chassis with slot cooling

capacity ≥58 W2

0 °C to 55 °C

All other compatible chassis 0 °C to 40 °C

Storage -40 °C to 71 °C

Humidity

Operating 10% to 90%, noncondensing

Storage 5% to 95%, noncondensing

Pollution Degree 2

Maximum altitude 2,000 m (800 mbar) (at 25 °C ambient temperature)

Compliance and Standards

Environmental Management

NI is committed to designing and manufacturing products in an environmentally responsible

manner. NI recognizes that eliminating certain hazardous substances from our products is

beneficial to the environment and to NI customers.

For additional environmental information, refer to the Commitment to the Environment web

page at ni.com/environment. This page contains the environmental regulations and directives

with which NI complies, as well as other environmental information not included in this

document.

Waste Electrical and Electronic Equipment (WEEE)

EU Customers At the end of the product life cycle, all NI products must be

disposed of according to local laws and regulations. For more information about

how to recycle NI products in your region, visit ni.com/environment/weee.

电子信息产品污染控制管理办法（中国 RoHS）

540

NI 符合中国电子信息产品中限制使用某些有害物质指令(RoHS)。关于 NI

中国 RoHS 合规性信息，请登录 ni.com/environment/rohs_china。

(For information about China RoHS compliance, go to ni.com/

environment/rohs_china.)

2Not all chassis with slot cooling capacity ≥58 W can achieve this ambient temperature range. Refer

to PXI chassis specifications to determine the ambient temperature ranges your chassis can achieve.

PXIe-416x Noise Filter Accessory User Guide | © National Instruments Corporation | 7

CE Compliance

This product meets the essential requirements of applicable European Directives, as follows:

• 2011/65/EU; Restriction of Hazardous Substances (RoHS)

Export Compliance

This product is subject to control under the U.S. Export Administration Regulations (15 CFR

Part 730 et. seq.) administered by the U.S. Department of Commerce's Bureau of Industry and

Security (BIS) (www.bis.doc.gov) and other applicable U.S. export control laws and sanctions

regulations. This product may also be subject to additional license requirements of other

countries' regulations.

Additionally, this product may also require export licensing before being returned to NI. The

issuance of a Return Material Authorization (RMA) by NI does not constitute export

authorization. The user must comply with all applicable export laws prior to exporting or re-

exporting this product. See ni.com/legal/export-compliance for more information and to

request relevant import classification codes (e.g. HTS), export classification codes (e.g.

ECCN), and other import/export data.

Product Certifications and Declarations

Refer to the product Declaration of Conformity (DoC) for additional regulatory compliance

information. To obtain product certifications and the DoC for NI products, visit ni.com/

product-certifications, search by model number, and click the appropriate link.

Additional Resources

Visit ni.com/manuals for information about the PXIe-4162/PXIe-4163 and the following

resources:

• The getting started guide for your module:

–PXIe-4162 Getting Started Guide

–PXIe-4163 Getting Started Guide

• The specifications for your module:

–PXIe-4162 Specifications

–PXIe-4163 Specifications

•NI DC Power Supplies and SMUs Help

•PXIe-4162/4163 Calibration Procedure

• The safety, environmental, and regulatory information for your module:

–PXIe-4162 Safety, Environmental, and Regulatory Information

–PXIe-4163 Safety, Environmental, and Regulatory Information

8| ni.com | PXIe-416x Noise Filter Accessory User Guide

NI Services

Visit ni.com/support to find support resources including documentation, downloads, and

troubleshooting and application development self-help such as tutorials and examples.

Visit ni.com/services to learn about NI service offerings such as calibration options, repair, and

replacement.

Visit ni.com/register to register your NI product. Product registration facilitates technical

support and ensures that you receive important information updates from NI.

NI corporate headquarters is located at 11500 N Mopac Expwy, Austin, TX, 78759-3504,

USA.

PXIe-416x Noise Filter Accessory User Guide | © National Instruments Corporation | 9

Information is subject to change without notice. Refer to the NI Trademarks and Logo Guidelines at ni.com/trademarks for

information on NI trademarks. Other product and company names mentioned herein are trademarks or trade names of their

respective companies. For patents covering NI products/technology, refer to the appropriate location: Help»Patents in your

software, the patents.txt file on your media, or the National Instruments Patent Notice at ni.com/patents. You can find

information about end-user license agreements (EULAs) and third-party legal notices in the readme file for your NI product. Refer

to the Export Compliance Information at ni.com/legal/export-compliance for the NI global trade compliance policy and how

to obtain relevant HTS codes, ECCNs, and other import/export data. NI MAKES NO EXPRESS OR IMPLIED WARRANTIES AS

TO THE ACCURACY OF THE INFORMATION CONTAINED HEREIN AND SHALL NOT BE LIABLE FOR ANY ERRORS. U.S.

Government Customers: The data contained in this manual was developed at private expense and is subject to the applicable

limited rights and restricted data rights as set forth in FAR 52.227-14, DFAR 252.227-7014, and DFAR 252.227-7015.

378572A-01 May 6, 2021

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere National Instruments Aufnahmegeräte Handbücher

National Instruments

National Instruments PC/104-GPIB Bedienungsanleitung

National Instruments

National Instruments AT-DIO-32F Bedienungsanleitung

National Instruments

National Instruments VXI-AT2023 Bedienungsanleitung

National Instruments

National Instruments NI-CAN Bedienungsanleitung

National Instruments

National Instruments NI-845 Series Bedienungsanleitung

National Instruments

National Instruments GPIB-USB Series Montageanleitung

National Instruments

National Instruments MXI-2 Bedienungsanleitung

National Instruments

National Instruments NI 9467 Bedienungsanleitung

National Instruments

National Instruments UMI-7774 Bedienungsanleitung

National Instruments

National Instruments 6527 Bedienungsanleitung

National Instruments

National Instruments VXI-USB Bedienungsanleitung

National Instruments

National Instruments NI 951x Bedienungsanleitung

National Instruments

National Instruments sbRIO-9601 Bedienungsanleitung

National Instruments

National Instruments GPIB-232CT-A IBCL EPROM Bedienungsanleitung

National Instruments

National Instruments USB-8502 Bedienungsanleitung

National Instruments

National Instruments NI 9403 Bedienungsanleitung

National Instruments

National Instruments FieldPoint FP-1000 Kurzanleitung

National Instruments

National Instruments PXIe-8370 Bedienungsanleitung

National Instruments

National Instruments PCMCIA-232 Bedienungsanleitung

National Instruments

National Instruments NI PCIe-8255R Bedienungsanleitung

National Instruments

National Instruments Gigabit Ethernet (GigE) Interface Device NI... Bedienungsanleitung

National Instruments

National Instruments USB-8506 Bedienungsanleitung

National Instruments

National Instruments MXI Bedienungsanleitung

National Instruments

National Instruments Cabled PCI Express Bedienungsanleitung

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch