NavePoint Basic Series Bedienungsanleitung

OWNER’S MANUAL: Performance Series Wallmount Cabinet

THIS MANUAL APPLIES TO THE FOLLOWING SKUs:

00301081

00301082

00301083

00301074

00301075

00301078

00301079

00301080

00301076

00301077

00301000

Keep this information for further reference.

Thank you for purchasing a NavePoint product.

Please examine the product for any damaged parts. If any part is damaged or missing, contact NavePoint for assistance. Do not attempt to install or

use product if it has been damaged. This product contains small items that could be a choking hazard – keep these items away from children.

During installation, lay product contents on cardboard or other protective surface to avoid any damage.

Do not use with equipment that is heavier than the indicated weight capacity for this product. This product is designed to be installed indoors on wood

stud walls, solid concrete walls or brick walls. Make sure that the supporting surface will safely support the weight of the equipment and all attached

hardware and components. It is recommended that installation be performed by a qualiﬁed installer. NavePoint cannot be held responsible for damage

to equipment or personal injury resulting from improper use or installation of product.

Maintenance: Check that the product is secure and safe to use at regular intervals (at least every three months).

Limitations of Liability: In no event will NavePoint, LLC. be liable for any damages, whether direct or indirect, special, punitive, incidental or

consequential damages (including, but not limited to, lost proﬁts or revenue, loss of use, lost business opportunities or loss of goodwill) or for the costs

of procuring substitute products, arising out of or in connection with the use of the product, whether such liability arises from any claim based upon

contract, warranty, tort (including negligence), product liability or otherwise, whether or not seller has been advised of the possibility of such loss or

damage. In no event will seller’s total cumulative liability, from all causes of action and all theories of liability, exceed the total amounts actually paid to

seller by customer under the order that gives rise to any liability hereunder.

www.NavePoint.com 2 [email protected]

1. Parts Identification

1. Top Panel x1

2. Bottom Panel x1

3. Frames x2

4. Front Door x1

5. Side Panels x2

6. Horizontal Beams x4

7. L Type Mounting Brackets x2

8. Back Panel x1

9. Hanger Bar x1

10. Vertical Mounting Rails x4

11. Cable Management Covers x2

Accessories List

A. M6 Screws x12 E. M8 Flange Nut x16

M6 Cage Nuts x12

M6 Plastic Washers x12 F. Casters (Optional) x4 (15U~22U)

B. M6*12 Screws x12 (6U~12U) G. M6 Self-tapping Screw x16 (For Casters)

x24 (15U~22U)

M6 Cage Nuts x12 (6U~12U) H. Lock Kit x1

x24 (15U~22U)

M6 Plastic Washers x12 (6U~12U) I. Anchors x4

x24 (15U~22U)

J. Ground Wire Kit x1

C. M4 Screw x12

White Plastic Washer x1

D. M8*12 Hex Head Screw x16

www.NavePoint.com 3 [email protected]

2. Cabinet Assembly

Detail A

STEP 1.

Lay Bottom Panel (#2) on the hard surface. Insert Front and Rear Frames (#3) with large flange oriented to

the inside. Be sure that the slots in the center of the frames are facing inward as shown in Detail A.

Overlay the Horizontal Beams(#6) so that the notches interlay with large flanges on the Front and Rear Frames

(#3). Be sure to orient the Horizontal Beams (#6) so that the flat, cage nut surface is facing inward.

Attach with 8 M8 Hexagon Screws (Bag D) and 8 M8 Flange Nuts (Bag E).

www.NavePoint.com 4 [email protected]

STEP 2.

Place the Top Panel (#1) on the hard

surface. Turn the assembly over and insert

it into the top panel. Be sure that the Top

and Bottom Panels (#1 and #2) are oriented

in the same direction (front matches front,

back matches back).

Overlay the Horizontal Beams(#6) so that

the notches interlay with large flanges on

the Front and Rear Frames (#3). Be sure to

orient the Horizontal Beams (#6) so that

the flat, cage nut surface is facing inward.

Attach with 8 M8 Hexagon Screws (Bag D)

and 8 M8 Flange Nuts (Bag E).

Detail B

STEP 3.

Install the 4 Vertical Rack Rails (#10) to the Horizontal Beams (#6) at the desired depth using the Cage Nut Kit

provided (Bag A). When determining the appropriate depth, be sure to consider the equipment that you plan

to mount inside the enclosure.

Note: Be sure that the rail depth is the same on both sides of the cabinet.

www.NavePoint.com 5 [email protected]

Detail C

Optional: Mount L Type Mounting Brackets (#7) to the Vertical Mounting Rails on each side of the cabinet

using the Cage Nut Kit provided (Bag A). (Note: To mount the L Type Mounting Brackets (#7), the depth

between front and back vertical rails should be 11’’ (280mm) for 450mm depth cabinet and 16.9’’ (430mm)

for 600mm depth cabinet.)

STEP 4.

Install the two Side Panels (#5) into place

using the Side Panel Latches. Once each

Side Panel (#5) is attached, test to ensure

that each Side Panel Lock locks properly.

www.NavePoint.com 6 [email protected]

STEP 5.

Install the Front Door Lock (Bag H) on the

Front Door (#4) as shown in left picture.

Detail D

STEP 6.

To attach the Front Door (#4) to the cabinet, locate the side with the two pins. Insert the bottom fixed pin

with White Plastic Washer (Bag C) into the door hinge hole. With your thumb, pull down on the top spring

pin and slide it into place over the second door hinge hole and release. NOTE: Each side of the front of the

cabinet has door hinge holes; this allows you to choose the door swing orientation.

www.NavePoint.com 7 [email protected]

STEP 7.

Attach the Back Panel (#8) to the cabinet

using 6 black M4 Screws (Bag C).

Optional: Attach the Top and Bottom Cable

Management (#11) Covers using 4 M4

Screws (Bag C) .

www.NavePoint.com 8 [email protected]

3. Mounting the Cabinet to the wall

Detail E

Attach the Hanger Bar

(#9) to a wall or other

suitable mounting surface

using 4 appropriate

anchors.

Note: When mounting

the mounting plate to the

wall, be sure the 2

mounting hooks are

facing outwards and

away from the wall.

After the Hanger Bar (#9)

has been securely

attached to the mounting

surface, hang the

cabinet’s 2 mounting

notches onto the 2

mounting hooks on the

plate attached to the

wall. The notches will fit

over the hooks and the

enclosure should slide

down onto the hooks

until secure.

www.NavePoint.com 9 [email protected]

After the Hanger Bar (#9)

has been secured and the

cabinet hung properly,

secure the cabinet to the

mounting plate using 2

M4 Screws (Bag C) in the

holes on the mounting

hooks as shown.

Warning: Do not attempt to

mount to wall, when

equipment is mounted

inside cabinet. The cabinet

can hold up to 130 pounds

evenly distributed. Make

sure wall surface can hold

weight of the cabinet and

equipment.

Optional: Attach Casters

(Bag F) with 16 M6 Self

Tapping Screws (Bag G) to

Bottom Panel (#2).

(Optional and only

compatible and included

with 15, 18 and 22U

versions of the

Performance Series

Cabinets)

www.NavePoint.com 10 [email protected]

4. Equipment Installation

1 Rack Unit

-Squared Hole Mounting

1 Locate the numbered square openings in the Vertical Mounting Rails (#10) where you plan to install your

equipment. Install M6 Cage Nuts (Bag B) into the square openings to provide an attachment point for the M6

Mounting Screws (Bag B). Note: Consult your equipment documentation to determine how many cage nuts

will be required and where they will need to be installed.

a- From the inside of the Vertical Mounting Rails (#10), insert one of the flanges of the cage nut through the

square opening. Press it against the side of the square opening.

b- Compress the cage nut at the sides slightly to allow the remaining flange to fit through the square

opening. When the cage nut is properly installed, both flanges will protrude through the square opening and

will be visible on the outer surface of the mounting rail. Repeat steps 1a and 1b until all required cage nuts

are installed.

2 After installing the required cage nuts, use the included M6 Mounting Screws (Bag B) and M6 Plastic

Washers (Bag B) to secure your equipment into the installed M6 Cage Nuts.

Andere Handbücher für Basic Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere NavePoint Netzwerk-Hardware Handbücher

NavePoint

NavePoint Consumer Series Bedienerhandbuch

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung