5 2
FCC/CE WARNING
This equipment generates and uses radio frequency energy and if not installed and used properly,
that is, in strict accordance with the manufacture's instructions, may cause interference to radio and
television reception. It has been tested and found to comply with limits for a Class B digital device in
accordance with Part 15 of FCC Rules and CE I-ETS 300 440, which are designed to provide
reasonable protection against such interference in a residential installation. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
1. Reorient the TV/radio antenna.
2. Relocate the Receiver away from the TV/radio receiver.
3. Plug the Receiver into a different wall outlet so that the Receiver is on a different branch circuit.
4. If necessary, the user should consult the dealer or an experienced radio/television technician for
additional suggestions.
The user may find the following booklet prepared by the Federal Communication Commission helpful:
"How to Identify and Resolve TV Interference Problems." This booklet is available from the US
Government Printing Office, Washington, D.C. 20402, Stock No. 004-000-00345-4.
FCC/CE NOTICE
The user is cautioned that changes or modifications not expressly approved by the manufacturer
could void the user's authority to operate the equipment. Linear radio controls provide a reliable
communications link and fill an important need in portable wireless signaling. However, there are
some limitations which must be observed.
The radios are required to comply with FCC Rules and Regulations as Part 15 devices and CE I-ETS
300 440. As such, they have limited transmitter power and therefore limited range. A receiver cannot
respond to more than one transmitted signal at a time and may be blocked by radio signals that occur
on or near their operating frequencies. Changes or modifications to the device may void FCC and CE
compliance. Infrequently used radio links should be tested regularly to protect against undetected
interference or fault.
Specifications
RECEIVER:
RECEIVING DISTANCE Up to 300 Feet
(Clear Line of Sight)
VIDEO OUT 1 Vp-p 75 Ohm
AUDIO OUT 1 Vp-p 600 Ohm
POWER SUPPLY 10V DC, 600 mA
OPERATING TEMP. 32°F - 122°F
0°C - 50°C
RADIO & CAMERA:
IMAGE SENSOR 1/3" Color CMOS
Image Sensor
RESOLUTION 330 Horizontal TV Lines
LENS 6mm
OPERATING TEMP. 32°F - 122°F
0°C - 50°C
Installing the Wireless Color Hidden Camera System
To install the system, follow these steps:
Receiver:
1. Plug the AC/DC adapter cord into the DC input jack on the back of the receiver.
2. Plug the audio/video cord to the audio/video output jack of the receiver. Plug the other end of
the cord to the audio/video input jacks on your TV or monitor.
3. Plug the AC/DC adapter into a standard (110V-240V) outlet. The power indicator LED
located on the top of the receiver should light.
Camera/Radio:
1. Plug the AC/AC adapter cord into the power input jack on the back of the unit.
2. Plug the AC/AC adapter into a standard (110V-240V) AC outlet. Set the camera/radio power
switch to "ON". The alarm indicator should light.
3.
System Setup:
1. Select the channel (Channel 1-4) to be used on both the camera/radio and receiver.
NOTE: Make sure the camera/radio and receiver are set to the same channel (1, 2, 3 or 4).
2. Set the selected channel by gently pushing the dip-switch for that channel to the ON position on
both the camera/radio and the receiver.
For example, to set both the camera/radio and receiver on Channel 1:
(a) Push the Channel 1 dip-switch located on the back of the
camera/radio and the side of the receiver to the ON position.
(b) Make sure the remaining dip-switches are in the OFF
position. In this case, channels 2 and 3 should be in
the OFF position.
If more than one camera/radio is to be installed and operated at the same time:
Simply follow steps (a) and (b) and set the
dip-switches for the other channels on the
camera/radio and receiver to ON.
For example, to operate two camera/radios: set
Camera/Radio 1 to Channel 1 (other channels off),
set Camera/Radio 2 to Channel 2 (other channels off),
and on the receiver, set channels 1 and 2 to ON.
See “Camera/Radio and Receiver Setting Chart” below for more detailed instructions.
3. Position and Rotate/adjust the receiver antenna toward the camera/radio for best performance.
FREQUENCY AM 530-1600 KHz
FM 88-108 MHz
DIMENSIONS 170 x 115 x 45 mm (approx.)
DC BACKUP POWER DC 9V. One 6F22 or equi
Size Battery (Not included)
ANTENNA FM with 1m Wire Antenna.
AM with Build-in Ferrite Bar Antenna
*Design and specification are subject to change without notice.
POWER OPERATION 18V AC/AC Adapter,
110-240V 50/60 Hz, 350mA
SPEAKER 2 1/4" 8 ohm Dynamic Loudspeaker
1 2 3 4
ON
CH1
Camera 1
1 2 3 4
ON
Camera 2
1 2 3 4
ON
Camera 3
1 2 3 4
ON
Camera 4
1 2 3 4
ON
Receiver
CH2
CH3
CH4
Camera/Radio & Receiver Channel Setting Chart
1. This 2.4 GHz system can be connected with up to 4
channels. Set channels on the camera/radio and
receiver before starting the system.
2. Set camera/radio and receiver channels by gently pushing
the switches with an object such as a pen or pencil to the
ON or OFF position. Use the illustrations shown on the right
as a guide. The switches are inset into the camera/radio and
receiver housings to avoid accidentally changing the
channel settings.
3. The Auto Sequential Scanning feature automatically
activates when more than one switch is set to ON.
ON
ON ON ON
1 2 3 4 1 2 3 4
ON
1 2 3 4 1 2 3 4 1 2 3 4
Camera Set to
Channel 1
Camera 1
Set to
Channel 1
Camera 2
Set to
Channel 2
Receiver Set
to Channel
1 & 2
Receiver Set to
Channel 1
WEIGHT Approx. 0.5LB/209.6g
DIMENSIONS Approx. 3.7" x 1.8" x 2.5"
9.5 x 4.7 x 6.3cm (LxWxH)
