NC-link NC-H91G Bedienungsanleitung
User Manual of Access Controller
Version V1.2
1
www.nc-link.cn
Thank you for purchasing NC-Link Access Controller. This manual will instruct
you how to configure and manage the APs with this controller, enable you to use
it in a perfect status.
Please check the Package before use it.
Package Contents
Item
Description
Unit
QTY
1
Access Controller
PCS
1
2
Power Cord
PCS
1
3
Mounting Accessory(H91G)
Set
1
4
Quick Installation Guide
PC
1
1. Manual Instruction
This manual is subject to tell users how to use this Wireless Access Controller
properly. Contents include description of this platform’s properties, and how to
configure this platform. Pre-reading this manual before operation is highly
recommended.
1.1 Target Reader
This manual is for those familiar with basic networking knowledge and
terminology
1.2 Conventions
If without extra explanation, this device, or WIFI management platform
mentioned on this guide stands for AC Controller Wifi management
platform, short for AC Controller
2. Product Introduction
Access Controller is a highly performance Wi-Fi management platform,
especially for Wi-Fi in hotel or Small & Medium Enterprise.
It’s capable for managing all NC-Link Access point, features with AP
auto-detection, AP status preview, AP configuration, MAC filtering, AP software
upgrade simultaneously, AP group ect. Match up with NC-Link Access Point to
provide high performance & reliable solution.
2.1 Product Layout
2.1.1 Front Panel
2
www.nc-link.cn
LED Indicator
LED
Name
Indication
Power
Power Light
Power is ON, means status is up
Power is OFF, mean status is
down
Run
System Light
Flashing, means system status is
normal
OFF or Solid, means status is
abnormal
Reset Button
If need to restore the Access Controller into factory default, please do
following procedure: Power on AC Controller, use a pin to press and hold
the reset button until all LED becomes quick-flash.
Then release the button and wait for AC Controller to reset to factory
default setting. After reset, the default IP address of Access Controller is
192.168.10.1, default user name and password are admin.
RJ45 Connector
5x 10/100M/1000Mbps auto-negotiation RJ45 Ethernet Port
Notice:
LAN/WAN port is LAN port only on the default mode, only when WAN
setting is enabled then LAN/WAN port will change to WAN port.
2.1.2 Rear Panel
DC Connector
DC Connector located on the right side of Access Controller’s rear panel,
input power is AC 100-240V~ 50/60Hz 0.3A
Grounding For Lightening
Please deploy ground connection to avoid lightening stroke, detail
installation please refer to “Grounding For Lightening Guide”.
3. Login
Please make sure the following items before login the Access Controller.
3
www.nc-link.cn
Access Controller has normal powered on, LAN port has been connected
with the management host
The management host has been properly installed IE 7.0 or higher
browser version
IP Address is dynamic
Login Steps:
Open IE browser, input http://192.168.10.1 in the address bar to login AC Controller’s
Web management interface.
Access Controller login screen require user name and password, the default is
admin, input and click “OK”
After login, you can see below Web page
4
www.nc-link.cn
4. Function Setting
4.1 Device List
Menu in the right side.
Batch Set: Setting Access Points with same parameters in one time
Refresh: Refresh the status of the Access Point
Delete: Delete the Access Point shown in the list
Clear all devices: Clear all devices shown in the list
Reboot: Reboot the Access Point you select
Reset: Reset the Access Point you select
Upgrade: Upgrade the Access Point you select
5
www.nc-link.cn
Notice:
All the functions in the right menu, you have to select at least one device.
The Access Points display in the list, you can also set particular one through click
edit of the device.
Device Status
6
www.nc-link.cn
Device Network
Wireless Basic
7
www.nc-link.cn
Wireless Advanced
4.2 Zero Config
Zero Config is a configuration assigned by controller when the Access
Point is detected with default setting. Like Access Point is first connect to
controller or the Access Point after reset to default setting.
Click “New”to set the Zero Config
8
www.nc-link.cn
Set the Group Name of the Zero Config, and also you can set the detail time to make
it reboot to optimize the devices status.
The first part is the Wireless Basic.
Device List: Wlan Device 1 is for 2.4GHz; Wlan Device 2 is for 5.8GHz
Status: Enable or Disable the wireless signal
Broadcast SSID: Enable or Disable broadcast SSID
SSID: Set the SSID
VlanId: Set the VLAN ID if needed
9
www.nc-link.cn
Wireless Security default is Open. Click the “Config”to set the encryption you need.
The second part is the Wireless Advanced.
Device List: Wlan Device 1 is for 2.4GHz; Wlan Device 2 is for 5.8GHz
Client Isolation: Enable or Disable client isolation
RF Output Power: To set the RF Output Power of the device, it divided into 100%,
75%, 50%, 25%, 12.5%
Coverage Threshold: To limit the RSSI of the access device
Note: Other advanced setting is for more professional or maintenance person,
suggest to keep them as default.
Wlan Device 2 is also the same way for setting if it needs 5.8GHz. After all the
parameter finished, click “Apply”and you will see the Zero Config is generated and
show as below:
Inhaltsverzeichnis
