NEC Multi Sync EA221WM Bedienungsanleitung

Dieses Handbuch passt für folgende Modelle

6

Inhaltsverzeichnis

Andere NEC Monitor Handbücher

NEC

NEC MultiSync LCD3090WQXi Bedienungsanleitung

NEC

NEC MultiSync LCD4010 Bedienungsanleitung

NEC

NEC MultiSync LCD1560VM Bedienungsanleitung

NEC

NEC MultiSync P702 Bedienungsanleitung

NEC

NEC NEC MultiSync LCD1850E LCD1850E LCD1850E Bedienungsanleitung

NEC

NEC MultiSync EA191M Bedienungsanleitung

NEC

NEC LCD Monitor Bedienungsanleitung

NEC

NEC PlasmaSync 50XM5 Bedienungsanleitung

NEC

NEC MultiSync LCD1510 Bedienungsanleitung

NEC

NEC AS191 - AccuSync - 19" LCD Monitor Bedienungsanleitung

NEC

NEC MultiSync EX241UN-BK Bedienungsanleitung

NEC

NEC 42XP10 - PlasmaSync - 42" Plasma Panel Bedienungsanleitung

NEC

NEC ESERIES Bedienungsanleitung

NEC

NEC V321-2 Bedienungsanleitung

NEC

NEC LCD1700NX - MultiSync - 17" LCD Monitor Bedienungsanleitung

NEC

NEC AccuSync LCD203WXM Bedienungsanleitung

NEC

NEC MultiSync P435 Bedienungsanleitung

NEC

NEC PlasmaSync 42XM4 Benutzerhandbuch

NEC

NEC MultiSync LCD1510 Bedienungsanleitung

NEC

NEC LCD175VXM - MultiSync - 17" LCD Monitor Bedienungsanleitung

NEC

NEC MULTISYNC P461 DST Bedienungsanleitung

NEC

NEC MultiSync LCD2060NX Leitfaden

NEC

NEC MultiSync X401S Bedienungsanleitung

NEC

NEC DPro2070SB Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung

LG

LG M1950D-PZ Bedienungsanleitung

COLOR MONITOR Multi Sync EA221WM

MODELS: EA221WM-BK (A)

EA221WM (B)/EA221WM-BK (B)

EA221WM (J)/EA221WM (BK) (J)

3rd Edition

NEC DISPLAY SOLUTIONS, LTD.

201006

08HR4LAN 08HR3LBN

08HR4LBN 08HR3LJN

08HR4LJN 08HR7LBW

08HR8LBW 08HR2GAN

08HR1GBN 08HR2GBN

08HRTLAN

PART NO. 599910918

SERVICE MANUAL

When EA221WM is repaired, this manual is the description of the necessary matter.

VERY IMPORTANT!

This Equipment is compatible with RoHS Directive and Lead-Free.

Since the equipment is compatible with RoHS Directive, use components in which the use of specific

chemically noxious substances is restricted; use only designated spare parts when it is necessary to

replace such parts with new parts.

Use lead-free solder for the equipment compatible with ones with substrates on which lead-free

components are mounted. For the details, refer to “Caution for Lead-Free Soldering Work” given in the

next page.

This model has four types of LCD panel.

●The panel type manufactured by LG (LM220WE1-TLD1)

●The panel type manufactured by LG (LM220WE1- TLE3)

●The panel type manufactured by SEC (LTM220M1-L01)

●The panel type manufactured by LG (LM220WE1-TLP1)

Prior to servicing the unit, confirm the serial number of the unit.

The classification code of the serial number is [0, 1].

The classification code of the serial number is [2, 3].

The classification code of the serial number is [6, 7].

The classification code of the serial number is [B].

1. Safety guideline in servicing

1) Never touch the portions with the marking ( ).

2) Do not expose the set to rain or water.

A risk of fire or electric shock can result.

3) Use an adequate power cord.

A risk of fire or electric shock can result.

4) Do not attempt to service or modify the set without prior permission of the manufacturer.

A risk of fire or electric shock can result.

5) Leave the maintenance service to a service engineer having qualification, knowledge and experience.

A risk of electric shock, injury or fire can result.

6) Always employ genuine parts indicated in the service manual for replacement.

A risk of fire or electric shock can result.

7) Confirm the connection of the power supply connector earth cable in reassembling. (Soldering or Screw

fixation)

A risk of fire or electric shock can result.

8) Use the specified binding bands, clampers, tubes and barriers--all of which are necessary for

insulation/protection--in their original positions in reassembling.

A risk of fire or electric shock can result.

9) Other complete parts are returned to an appropriate position.

2. Other cautions necessary

1) When removing the cables from their connectors, take care not to damage the wire portions so as to prevent the

occurrence of poor contact.

2) When attaching/detaching screws, use a screwdriver that is well-fit to the screw size.

3. Caution for LEAD-FREE soldering work

For this equipment, parts compatible with lead-free materials are used. Please observe the following precautions,

when performing any soldering work.

1) Use lead-free solder for substrates mounted with lead-free parts. If you use eutectic solder by mistake, solder will

not fuse well because of the difference in fusion point.

2) Fusion Point

Lead-free solder: 220°C

Eutectic solder: 183°C

3) Solder composition of Lead-free solder: Sn-3.0Ag-0.5Cu

[Maker ] [Type]

Nihon Genma DHB-RMA NP303-###

Senju metal ESC F3 M705E-###

(#: This mark shows the diameter of the solder wire.)

4) When working with lead-free solder always use a temperature adjustable soldering iron. Moreover, the power

consumption of the soldering iron must use from 25W to 75W.

[Solder Iron tip temperature and contact time]

Category of Parts Lead-free solder Eutectic solder

*SMD Chip The Parts of Chip type 300-320°C(1-3sec) 260-280°C(1-3sec)

*SMD QFP The Parts (IC) of Quad Flat Pack Package type 320-350°C(1-3sec) 280-300°C(1-3sec)

Heat sink Heat sink 360-380°C(1-3sec) 320-420°C(1-3sec)

The Parts of Axial or Radial type

(The Electric Parts other than the above-mentioned.

Ax, RD

Ex.: IC, Transistor, Resistor, Capacitor)

340-370°C(1-3sec) 350-390°C(1-3sec)

Procedure of monitor repair

Confirmation of

monitor version

Confirmation of

defective parts

Replacement of

defective parts

What are

replacement

parts ?

Writing of EDID/OSD data

Adjustment of monitor

Inspection of monitor

“SWAP” or “Repair and Return”?

Was MAIN PWB

replacement ?

Was LCD panel

replacement?

Was Other parts

replacement ?

1. SERIAL NUMBER INFORMATION

2. TROUBLE SHOOTING

3. DISASSEMBLY

4. ADJUSTMENT PROCEDURES

5. INSPECTION PROCEDURES

6. Writing of EDID/OSD (Monitor Information) data

Electric parts

Yes

Yes

Yes

1 2

SWAP

Repair and Return

Appearance parts

or No

(

NPF

)

[Repair and Return]

[SWAP]

1

Was MAIN PWB

replacement?

Shipment setting Factory preset Repair completion

Yes

No

7. SHIPMENT SETTING OSD User menu

2

Shipment setting Factory preset Repair completion

7. SHIPMENT SETTING OSD User menu

CONTENTS

1. SERIAL NUMBER INFORMATION .................................................... 1-1

2. TROUBLE SHOOTING ...................................................................... 2-1

3. DISASSEMBLY .................................................................................. 3-1

4. ADJUSTMENT PROCEDURES ......................................................... 4-1

5. INSPECTION PROCEDURES ............................................................ 5-1

6. Writing of EDID/OSD (Monitor Information) data ............................ 6-1

7. SHIPMENT SETTING........................................................................... 7-1

8. PACKING SPECIFICATION ............................................................... 8-1

9. REVISION HISTORY .......................................................................…9-1

1-1

1. Serial Number Information

Refer to the serial number information shown below.

EX.) SERIAL NUMBER LABEL

(1):ManufacturedYear (3):Classificationcode (9):FactoryCode

(2): Manufactured Month (4) ~ (8): Running number (10): Control Code

MODEL:

SERIAL NO.: gggggggggg

(1) (2) (3) (4) (5) (6) (7) (8) (9) (10)

January to September: 1 to 9

October: X

November: Y

December: Z

This running number does not reset at each month. For A ver. (U.S/Asia/Australia.): A

For B ver. (Europe/Asia/Australia.): B

For J ver. (Japan): J

TPV China factory: N

Czech Tatung :W

Discriminate by cabinet colorLast digit

(□) Panel code

1-2

MODEL Panel Code (3) (9) (10) LCD Panel RoHS Vista

EA221WM-BK (L) 1(Black) N(TPV China Factory) A(USA) LM220WE1-TLD1 Yes Yes

EA221WM (L) 0(White) N(TPV China Factory)

W (Czech Tatung) B(Europe) LM220WE1-TLD1 Yes Yes

EA221WM-BK (L) 1(Black) N(TPV China Factory)

W (Czech Tatung) B(Europe) LM220WE1-TLD1 Yes Yes

EA221WM (L) 0(White) N(TPV China Factory) J(Japan) LM220WE1-TLD1 Yes Yes

EA221WM(BK) (L) 1(Black) N(TPV China Factory) J(Japan) LM220WE1-TLD1 Yes Yes

EA221WM-BK (L) 3(Black) N(TPV China Factory) A(USA) LM220WE1-TLE3 Yes Yes

EA221WM (L) 2(White) N(TPV China Factory)

W (Czech Tatung) B(Europe) LM220WE1-TLE3 Yes Yes

EA221WM-BK (L) 3(Black) N(TPV China Factory)

W (Czech Tatung) B(Europe) LM220WE1-TLE3 Yes Yes

EA221WM (L) 2(White) N(TPV China Factory) J(Japan) LM220WE1-TLE3 Yes Yes

EA221WM(BK) (L) 3(Black) N(TPV China Factory) J(Japan) LM220WE1-TLE3 Yes Yes

EA221WM-BK (S) 7(Black) N(TPV China Factory) A(USA) LTM220M1-L01 Yes Yes

EA221WM (S) 6(White) N(TPV China Factory) B(Europe) LTM220M1-L01 Yes Yes

EA221WM-BK (S) 7(Black) N(TPV China Factory) B(Europe) LTM220M1-L01 Yes Yes

EA221WM-BK (L) B(Black) N(TPV China Factory) A(USA) LM220WE1-TLP1 Yes Yes

2-1

2. TROUBLE SHOOTING

2.1 No Power

NG

OK

NG

Check the AC power.

NG

OK

The power supply equipment is

confirmed.

The power on/off switch

is turned on.

Loosening of the power supply

connector is checked.

Check connections of

POWER PWB or MAIN PWB.

No Power

OK

NG

OK

Replace AC power cable or AC inlet.

Replace the POWER PWB. OK

NG

The cable connector is inserted.

NG

End

Replace the MAIN PWB.