NEC MultiSync FE750 Administratorhandbuch

COLOR MONITOR MultiSync!

!FE750

MODELS FE750 (A) / (B) /(R)

NEC Corporation 200003

08109353

08109354

08109355

SCHEMATIC DIAGRAMS

PART NO. 599910513

WARNING

The SERVICE PERSONNEL should have the appropriate technical training, knowledge and experience

necessary to:

･Be familiar with specialized test equipment, and

･Be careful to follow all safety procedures associated with high voltage CRT circuit designs to minimize

danger to themselves and their coworkers.

To avoid electrical shocks, this equipment should be used with an appropriate power code and be

connected only to a properly grounded AC outlet.

This equipment utilized a micro-gap power switch. Turn off the set by first pushing the front panel

power switch. Next, remove the power cord from the AC outlet.

To prevent fire or shock hazards, do not expose this unit to rain or moisture.

This symbol warns the personnel that un-insulated voltage within the unit may have sufficient

magnitude to cause electric shock.

This symbol alerts the personnel that important literature concerning the operation and

maintenance of this unit has been included.

Therefore, it should be read carefully in order to avoid any problems.

PRODUCT SAFETY CAUTION

1. When parts replacement is required for servicing, always use the manufacturer's specified replacement.

2. Comply with all caution and safety-related notes on the product display chassis and picture tube.

3. When replacing the component, always be certain that all the components are put back in the place.

4. When servicing display monitor unit, it is required that the provided lead dress is used in the high voltage

circuit area.

5. It is also recommended that shatter proof goggles are worn, when removing installing and handling the

picture tube. People not equipped with the proper precautionary measures mentioned should keep the

picture tube away from body while handling.

6. As for a connector, pick and extract housing with fingers properly since a disconnection and improper

contacts may occur, when wires of the connector are led.

7. Use a proper screwdriver. If you use screwdriver that does not fit, you may damage the screws.

8. X-radiation precaution

This product contains critical electrical and mechanical parts essential for X-ray protection.

Normal anode voltage is 25.0 kV at zero beam picture tube current under AC 100-120V/220-240V input,

and anode voltage must not exceed the voltages shown below under any operation condition.

To measure anode voltage set brightness for very dim picture, and use a high impedance volt meter

between chassis and anode lead and measure high voltage.

If high voltage exceeds the specifications on the chassis schematic diagram, take the necessary

corrective action.

Table MAXIMUM ANODE VOLTAGE

beam current at 0 mA at 0.7 mA at 1.4 mA

A/B/R 34.5 kV 32.5 kV 31.0 kV

9. When you degauss the set with an external degaussing coil, you must keep strictly item “ * Notes about

degaussing method ” of ADJUSTMENT PROCEDURES.

FE750

SCHEMATIC DIAGRAMS

CONTENTS

PageNo.

MAIN PWB (1/4) SCHEMATIC DIAGRAM .................................................................. 1

MAIN PWB (2/4) PWB SCHEMATIC DIAGRAM ......................................................... 2

MAIN PWB (3/4) PWB SCHEMATIC DIAGRAM ......................................................... 3

MAIN PWB (4/4) SCHEMATIC DIAGRAM ................................................................... 4

SUB PWB SCHEMATIC DIAGRAM ............................................................................. 5

CRT PWB SCHEMATIC DIAGRAM ............................................................................. 6

OSC PWB SCHEMATIC DIAGRAM ............................................................................. 7

CONTROL PWB SCHEMATIC DIAGRAM .................................................................... 8

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere NEC Monitor Handbücher

NEC

NEC MultiSync E273F Bedienungsanleitung

NEC

NEC MultiSync 77F Bedienungsanleitung

NEC

NEC LCD195NXM - MultiSync - 19" LCD Monitor Bedienungsanleitung

NEC

NEC AccuSync LCD72VX Bedienungsanleitung

NEC

NEC MultiSync LA-15R03-BK Bedienungsanleitung

NEC

NEC MULTISYNC LCD1510+ Handbuch

NEC

NEC X461UN - MultiSync - 46" LCD Flat Panel... Bedienungsanleitung

NEC

NEC MultiSync E203Wi Bedienungsanleitung

NEC

NEC MultiSync LCD2180UX Bedienungsanleitung

NEC

NEC MultiSync EA191M Bedienungsanleitung

NEC

NEC MultiSync EA261WM Bedienungsanleitung

NEC

NEC MultiSync E424 Bedienungsanleitung

NEC

NEC MDG5MP-BNDL Bedienungsanleitung

NEC

NEC PlasmaSync P42XP10-BK Bedienungsanleitung

NEC

NEC MultiSync LCD5710 Bedienungsanleitung

NEC

NEC MultiSync EA242WU Benutzerhandbuch

NEC

NEC PX-61XR4 Bedienungsanleitung

NEC

NEC PlasmaSync 50XM4 Bedienungsanleitung

NEC

NEC AccuSync LCD4000 Bedienungsanleitung

NEC

NEC NEC MultiSync LCD1550V LCD1550V LCD1550V Leitfaden

NEC

NEC MultiSync LCD1970VX Bedienungsanleitung

NEC

NEC MultiSync EA221WM Bedienungsanleitung

NEC

NEC MultiSync X431BT Bedienungsanleitung

NEC

NEC LCD8205-P - MultiSync - 82" LCD Flat Panel... Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung

LG M1950D-PZ Bedienungsanleitung