NEC ShadowSense Touch MultiSync P404 SST Bedienungsanleitung

User’s Manual

P Series ShadowSenseTM Touch

MultiSync P404 SST

MultiSync P484 SST

MultiSync P554 SST

MONITOR MODEL: P404 SST, P484 SST, P554 SST

Please find your model name on the label on rear side of the monitor.

Index

Addendum to User’s Manuals of MultiSync P404 & MultiSync P484 &

MultiSync P554….……………………………………………….…………………………….. Page 03

Registration Information……………………………………………………………………….. Page 04

Important Information………………………………………………………………………….. Page 06

Safety Precautions, Maintenance & Recommended Use…………………………………. Page 07

Shipping Content………………………………………………………………………………..Page 08

Unpacking………………………………………………………………………………………. Page 09

General Installation…………………………………………………………………………….. Page 10

Connections…………………………………………………………………………………….. Page 11

Troubleshooting………….…………………………………………………………………….. Page 13

Specifications – P404…………………………………………………………………………. Page 17

Specifications – P484……….…………………………………………………………………. Page 20

Specifications – P554……….…………………………………………………………………. Page 23

Manufacturer’s Recycling and Energy Information…………………………………………. Page 26

Addendum to User’s Manuals of MultiSync P404 / P484 / P554

This user’s manual is an addendum to the standard user’s manual of the base model monitors P404,

P484 and P554.

All specifications listed here supersede those in the standard version of the manual included with this

monitor.

NOTE: Following feature sets are not supported by the Pxx4 SST models:

-Room Light Sensing Sensor: Other than the standard monitor, the Pxx4 SST models do not allow

the monitor to make automatic adjustments to the backlight setting.

-NEC ornament logo: Other than the standard monitor, the Pxx4 SST models do not have an

ornament logo. Therefore changing the position of the NEC logo is not possible.

Registration Information

Cable Information

CAUTION: Use the provided specified cables with this product so as not to interfere with radio and

television reception. For USB please use a shielded signal cable with ferrite core. For HDMI,

DisplayPort and D-Sub 9-pin, please use a shielded signal cable. For Audio, please use a signal cable

with ferrite core. Use of other cables and adapters may cause interference with radio and television

reception.

DECLARATION OF CONFORMITY

Windows is a registered trademark of Microsoft Corporation.

NEC is a registered trademark of NEC Corporation.

MultiSync is a trademark or registered trademark of NEC Display Solutions, Ltd. in Japan and other

countries.

DisplayPort and DisplayPort Compliance Logo are trademarks owned by Video Electronics Standards

Association in the United States and other countries.

All other brands and product names are trademarks or registered trademarks of their respective

owners.

The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are

trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the United States and

other countries.

Trademark PJLink is a trademark applied for trademark rights in Japan, the United States of America

and other countries and areas.

microSD and microSD SDHC logos are trademarks of SD-3C, LLC.

CRESTRON and CRESTRON ROOMVIEW are trademarks or registered trademarks of Crestron

Electronics, Inc. in the United States and other countries.

Raspberry Pi is a trademark of the Raspberry Pi Foundation.

Adobe and the Adobe logo are either registered trademarks or trademarks of Adobe Systems

Incorporated in the United States and/or other countries.

GPL/LGPL Software Licenses

The product includes software licensed under GNU General Public License (GPL), GNU Lesser

General Public License (LGPL), and others. For more

information on each software, see “readme.pdf” inside the “about GPL&LGPL” folder on the supplied

CD-ROM.

Registration Information

Cable Information

CAUTION: Use the provided specified cables with this product so as not to interfere

with radio and television reception. For USB please use a shielded signal cable with ferrite

core. For HDMI, DisplayPort and D-Sub 9-pin, please use a shielded signal cable. For

Audio, please use a signal cable with ferrite core. Use of other cables and adapters may

cause interference with radio and television reception.

DECLARATION OF CONFORMITY

Windows is a registered trademark of Microsoft Corporation.

NEC is a registered trademark of NEC Corporation.

MultiSync is a trademark or registered trademark of NEC Display Solutions, Ltd. in Japan

and other countries.

DisplayPort and DisplayPort Compliance Logo are trademarks owned by Video

Electronics Standards Association in the United States and other countries.

All other brands and product names are trademarks or registered trademarks of their

respective owners.

The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are

trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the United

States and other countries.

Trademark PJLink is a trademark applied for trademark rights in Japan, the United States

of America and other countries and areas.

microSD and microSD SDHC logos are trademarks of SD-3C, LLC.

CRESTRON and CRESTRON ROOMVIEW are trademarks or registered trademarks of

Crestron Electronics, Inc. in the United States and other countries.

Raspberry Pi is a trademark of the Raspberry Pi Foundation.

Adobe and the Adobe logo are either registered trademarks or trademarks of Adobe

Systems Incorporated in the United States and/or other countries.

GPL/LGPL Software Licenses

The product includes software licensed under GNU General Public License (GPL), GNU

Lesser General Public License (LGPL), and others. For more

information on each software, see “readme.pdf” inside the “about GPL&LGPL” folder on

the supplied CD-ROM.

Important Information

This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause

electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of this unit

has been included. Therefore, it should be read carefully in order to avoid any problems.

CAUTION: Please use the power cord provided with this display in accordance with the table below. If a

power cord is not supplied with this equipment, please contact NEC. For all other cases, please use the power

cord with the plug style that matches the power socket where the monitor is located. The compatible power cord

corresponds to the AC voltage of the power outlet and has been approved by, and complies with, the safety

standards in the country of purchase.

This equipment is designed to be used with a power cord that has a protective earth pin connected to earth. If the

power cord is not connected to the earth, it may cause electric shock. Please make sure the power cord is

earthed properly.

* When operating this monitor with its AC 125-240V power supply, use a power supply cord that matches the

power supply voltage of the AC power outlet being used.

NOTE: This product can only be serviced in the country where it was purchased.

Use the power cord which has BSMI mark at both ends when you use this monitor in Taiwan.

• The intended primary use of this product is as an Information Technical Equipment in an office or domestic

environment.

• The product is intended to be connected to a computer and is not intended for the display of television

broadcast signals.

Safety Precautions, Maintenance & Recommended Use

Safety Precautions and Maintenance

Refer to the instruction explained on page English-3 of the standard user’s manual of the monitor.

Cleaning the Glass Surface

•The glass surface should be cleaned regularly with a soft, lint free cloth.

•It is recommended to use an anti-static plastic and glass cleaner suited for PMMA/acrylic

glass/Plexiglas, or water with a small amount of washing-up liquid.

Cleaning the Cabinet

•Unplug the power supply.

•Gently wipe the cabinet with a soft cloth.

•To clean the cabinet, dampen the cloth with a neutral detergent and water, wipe the cabinet and

follow with a dry cloth.

NOTE: DO NOT clean with benzene thinner, alkaline detergent, alcoholic system detergent, wax,

polish cleaner, soap powder or insecticide. Rubber or vinyl should not be in contact with the cabinet for

an extended period of time. These types of fluids and materials can cause paint to deteriorate, crack or

peel.

Shipping Content

MultiSync P404 SST

1. 40” ShadowSenseTM Touch Monitor

2. Remote Control

3. CD-ROM (User Guides/Manuals)

4. Addendum to User’s Manuals

5. Power Cable

6. DisplayPort Cable

7. 2x USB Cable 300cm

MultiSync P484 SST

1. 48” ShadowSenseTM Touch Monitor

2. Remote Control

3. CD-ROM (User Guides/Manuals)

4. Addendum to User’s Manuals

5. Power Cable

6. DisplayPort Cable

7. 2x USB Cable 300cm

MultiSync P554 SST

1. 55” ShadowSenseTM Touch Monitor

2. Remote Control

3. CD-ROM (User Guides/Manuals)

4. Addendum to User’s Manuals

5. Power Cable

6. DisplayPort Cable

7. 2x USB Cable 300cm

Unpacking

Unpacking the Display

Unpack the display (P404 SST, P484 SST, P554 SST) from the carton box by removing the white clips

on the bottom of the box.

NOTE: Due to the weight of the product, for installation and handling 2 people are required. DO NOT

start unless you have enough people available. Working with less people may result in injuries and

damaged product.

Lift the carton box upwards. Make sure to have one additional person to secure the display from

tipping over.

NOTE: Remember to save your original box and packing material to transport or ship the monitor.

For further instructions, please refer to the printed instruction on the carton box.

General Installation

This device cannot be used or installed without a mounting accessory for support. For proper

installation it is strongly recommended to use a trained, NEC authorized service person. Failure to

follow NEC standard mounting procedures could result in damage to the equipment or injury to the

user or installer. Product warranty does not cover damage caused by improper installation. Failure to

follow these recommendations could result in voiding the warranty

Mounting

For customer:

CAUTION

DO NOT mount the monitor yourself. For proper installation it is strongly recommended to use a

trained, qualified technician. Please contact your supplier, as they may be able to provide a list of

qualified installation professionals. Mounting on a wall or ceiling and hiring a technician is the

customer’s responsibility.

Maintenance

•Periodically check for looses screws, gaps, distortions, or other problems that may occur with the

mounting equipment. If a problem is detected, please refer to qualified personnel for service.

•Regularly check the mounting location for signs of damage or weakness that may occur over time.

DO NOT block ventilated openings with mounting accessories or other accessories.

For NEC Qualified Personnel:

Stability Hazard.

The device may fall, causing serious personal injury or death. To prevent injury, this device must be

securely attached to the floor/wall in accordance with the installation instructions. Carefully inspect the

location where the unit is to be mounted. Not all walls or ceilings are capable of supporting the weight

of the unit. Weight of this monitor is mentioned in Specification (P404 SST on page 18, P484 SST on

page 21 and P554 SST on page 24). Product warranty does not cover damage caused by improper

installation, remodeling, or natural disasters. Failure to comply with these recommendations could

result in voiding the warranty.

To ensure safe installation, use two or more brackets to mount the unit. Mount the unit to at least two

points on the installation location.

For further instructions, please refer to standard user’s manual of the base model monitors

P404, P484, P554.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere NEC Monitor Handbücher

NEC

NEC MultiSync M751 Bedienungsanleitung

NEC

NEC MultiSync 2A Bedienungsanleitung

NEC

NEC A Series Bedienungsanleitung

NEC

NEC JC-1431VMB Bedienungsanleitung

NEC

NEC P1150 - MultiSync - 21" CRT Display Technisches Handbuch

NEC

NEC MultiSync LCD4010 Bedienungsanleitung

NEC

NEC MD212MC - MultiSync - 21.3" LCD Monitor Bedienungsanleitung

NEC

NEC MultiSync E424 Bedienungsanleitung

NEC

NEC MultiSync ME431 Bedienungsanleitung

NEC

NEC MultiSync LCD1512 Bedienungsanleitung

NEC

NEC XG85-XG135LC Bedienungsanleitung

NEC

NEC MultiSync V422 Bedienungsanleitung

NEC

NEC MultiSync FE1250+ Leitfaden

NEC

NEC LCD2070WNX - MultiSync - 20.1" LCD Monitor Bedienungsanleitung

NEC

NEC MultiSync 55 Bedienungsanleitung

NEC

NEC AccuSync LCD200VX Bedienungsanleitung

NEC

NEC LCD2070NX - MultiSync - 20" LCD Monitor Bedienungsanleitung

NEC

NEC P221W-BK-SV - MultiSync - 22" LCD Monitor Bedienungsanleitung

NEC

NEC MultiSync X464UNV Bedienungsanleitung

NEC

NEC P42XC10 - PlasmaSync - 42" Plasma Panel Bedienungsanleitung

NEC

NEC MultiSync P402 Bedienungsanleitung

NEC

NEC MultiSync E500 Bedienungsanleitung

NEC

NEC MultiSync X401S Bedienungsanleitung

NEC

NEC MultiSync LCD1560V+ LCD1560V+ LCD1560V+ Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung

LG M1950D-PZ Bedienungsanleitung