NEC X551UN-TMX4P Bedienungsanleitung

NEC Display Solutions of America, Inc.

QIG-TMXP-55UN

X551UN-TMX4P Rev 1.0

Parts List

o(4) X551UN Displays

o(4) Overnight Onsite Service Warranties (ONSITE-55-17)

o(4) Peerless Pullout Wall Mounts (DS-VW765-LAND)

o(2) Custom Peerless Spacers (DS-VWS040)

o(4) 3m DVI-D to DVI-D M/M cables

o(1) 5m DVI-D to DVI-D M/M cable

o(3) 10m Null Modem to Null Modem F/F cables

o(1) IR/Remote Control Kit (KT-RC)

o(2) Overframe Bezel Kits (KT-55UN-OF)

o(2) Tripp Lite 6 Outlet Strip (ISOBar6)

NOTES:

oAny walls that this video wall solution is anchored to must be strong enough to support the displays and the

installation must be in accordance with any local building codes. All mounting apparatuses must make secure

contact to wooden studs.

oPlease read entire document before starting installation

NEC Display Solutions of America, Inc.

QIG-TMX-55UN

X551UN-TMX4P Rev 1.0

1. For mounting information, please refer to the Installation Instructions provided by Peerless

Manufacturing inside of the box of the DS-VW765-LAND mount units.

2. Connect the NEC displays using the included DVI cables and the integrated DVI

loopthrough connections on the bottom of each monitor. Note that the DVI connection

closest to the front of the display is the ‘in’ connection while the connection closest to the

wall is the ‘out’ connection.

The ideal cabling set up is shown below to match the ideal monitor ID configuration.

However, DVI daisy chaining can be done different ways and still yield the same results.

Note that the connections for each X551UN monitor are on the bottom of each display, not

the side as shown in the image below. It may be helpful to start wiring before mounting.

3. Connect the null modem cabling to each display. It is recommended to connect from

Display 1 to Display 2, from Display 2 to Display 3, and from Display 3 to Display 4. Note

that the null modem cable needed to run from the source computer to Display 1 is not

included in this bundle. This will need to be purchased separately to control the display

remotely over RS232. Also loop through the provided IR Remote control cables.

NEC Display Solutions of America, Inc.

QIG-TMX-55UN

X551UN-TMX4P Rev 1.0

4. Apply the OverFrame bezel kit to the video wall. Please follow instructions provided with kit

(KT-55UN-OF).

5. Screw the IR Receiver (KT-RC) directly to the outside of the video wall and plug it directly

into the IR In terminal of Display 1.

6. Set each monitor ID up individually through the ‘MULTI-DSP’ menu within the OSD. It’s

recommended that the ID’s go from left to right, with the ID No. 1 being in the top left corner.

Overframe Kit

IR In

RS232 In

RS232 Out

IR Out

NEC Display Solutions of America, Inc.

QIG-TMX-55UN

X551UN-TMX4P Rev 1.0

Note that after the ID’s are set, there are two different ways to communicate to each screen

via the IR Remote. If the setting for the ‘IR Control’ within the ‘MULTI-DSP’ menu is set to

‘Normal’, then the IR remote control cabling is being utilized for communication. In order to

communicate to each screen individually, hold down the ‘Remote ID Set’ button on the

remote control, tap the number of the ID that you want to communicate with, then release

the Remote ID Set button. To test if this was done correctly, press the MENU button and

the OSD should now only appear on the display in which the remote control is

corresponding to. Also, more information on this is located within the User’s Manual.

To communicate to each display over the RS232 connection, make sure that the first display

(monitor ID 1) has its IR control set to ‘Primary’, while all others are set to ‘Secondary’.

When this is set, press the ‘Display’ button and the Monitor ID and Target ID should come

up in the left corner of each screen. Use the [+] and [-] buttons on the remote to change the

Target ID to the desired display you wish to communicate with then press ‘Display’ again. If

the menu is then pressed, the OSD menu should appear on the screen of the desired ID.

7. Use the TileMatrix feature to setup the 2x2 Video Wall. The Tilematrix feature of the NEC

Display allows for one image to be expanded and displayed over a 2x2 Video Wall Setup.*

This is accessed through the OSD (On-Screen Display) Controls under the “MULTI-DSP”

main menu icon. Under the TileMatrix sub-menu, enable the feature and set the necessary

NEC Display Solutions of America, Inc.

QIG-TMX-55UN

X551UN-TMX4P Rev 1.0

parameters that match the 2x2 Video Wall setup. Note that this step will need to be

completed for each screen.

8. Select if TileComp is necessary for this application or not. TileComp works in tandem with

TileMatrix to compensate for the width of the tiled bezels in order to accurately display the

image. Click ‘YES’ on enable to display video wall. Note that this step will need to be

completed for each screen.

If you are experiencing issues with this setup, please call our Technical Support number at

(800) 632-4622

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere NEC Monitor Handbücher

NEC

NEC X461HB - MultiSync - 46" LCD Flat Panel... Bedienungsanleitung

NEC

NEC NEC MultiSync LCD1525V LCD1525V LCD1525V Bedienungsanleitung

NEC

NEC AccuSync AS192 Bedienungsanleitung

NEC

NEC MultiSync E241N Bedienungsanleitung

NEC

NEC XP21 - MultiSync - 21" CRT Display Bedienungsanleitung

NEC

NEC MultiSync 95F Bedienungsanleitung

NEC

NEC MultiSync EA231WMi Stücklistenhandbuch

NEC

NEC PlasmaSync 42VP4 Bedienungsanleitung

NEC

NEC PlasmaSync 4210W Bedienungsanleitung

NEC

NEC LCD1920NX BK - MultiSync - 19" LCD Monitor Fehlerbehebungshandbuch

NEC

NEC P221W-BK - MultiSync - 22" LCD Monitor Bedienungsanleitung

NEC

NEC LCD3215 - MultiSync - 32" LCD Flat Panel... Bedienungsanleitung

NEC

NEC DS TO DSX - CROSS Service-Handbuch

NEC

NEC MultiSync LCD1980FXi Bedienungsanleitung

NEC

NEC EA273WM-BK Bedienungsanleitung

NEC

NEC LCD1920NX BK - MultiSync - 19" LCD Monitor Bedienungsanleitung

NEC

NEC MultiSync LCD225WXM-BK Bedienungsanleitung

NEC

NEC AccuSync AS203WMi-BK Bedienungsanleitung

NEC

NEC MultiSync X464UNV Bedienungsanleitung

NEC

NEC MultiSync X461UNV Leitfaden

NEC

NEC MD211C2 Bedienungsanleitung

NEC

NEC MultiSync LCD195VXM+ Bedienungsanleitung

NEC

NEC LCD2470WNX - MultiSync - 24" LCD Monitor Bedienungsanleitung

NEC

NEC PG-2740 Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung

LG M1950D-PZ Bedienungsanleitung