NEC WT600 Series Kurzanleitung

NEC NEC Solutions (America), Inc.

VisualSystems

WhitePaper v1.0

WT600 Used In Rear Projection Systems

The WT600 has a very short throw distance that makes it an attractive product to use in a rear projection (RP) system.

By using the WT600, the depth of the rear projection system can be reduced by half of a system using a traditional

projector. It is possible to design a system with a 100” diagonal screen that has a total depth of approximately 24”

(single mirror system).

The key to using the WT600 in a rear projection system is ‘screen selection’.

The WT600 has a very steep projection angle (55°).

When the WT600 is installed on the opposite side of the screen from the viewer in an RP system, the image path

comes through the screen at a very steep angle. When the light path passes through the screen, the screen diffuses

much of the light so that the image can be seen from many angles. However some of the light keeps traveling at that

steep angle after it passes through the screen and keeps traveling up so that some light may pass over the viewers’

head when the projector is installed in desktop orientation. This portion of light is lost to the viewer (see diagram below).

55°

DIFFUSED

LIGHT

SOME LOST LIGHT

‘Hot spotting’ can also occur in areas on the screen, usually noticed at the very bottom of the screen in the middle,

when the projector is installed in desktop orientation. This is also dependant on the height of the viewer’s seating. In

testing the WT600 in the environments described, we have found the location of hot spotting and the intensity is not

very noticeable compared to a traditional projector with a rear lens where hot spotting tends to happen more around the

center of the screen and usually at more intensity.

Designers of RP Systems are also careful to use a screen and system designed to avoid the possibility of ‘secondary

reflection’. Secondary reflection can occur when an RP system with mirrors is used. Often diffusion screens have a

shiny side which when facing the projector can reflect some light back to the mirror which in turn will reflect back onto

the screen a second time (see diagram). This can cause a double image to occur. Secondary reflections can be

www.necvisualsystems.com Page 1 of 2

avoided by mounting the screen with the diffusion side toward the projector and the shiny side toward the viewer. This

look has much the same luster as a direct view TV. If a more matt surface is desired, screen manufacturers offer

screens with AR (anti-glare) coatings on the viewer side.

IMAGE HITS

SCREEN TWICE

MIRROR

A screen that will give the best results should be a ‘diffusion type’ and it should be installed so that the diffusion side is

facing the projector (not the viewer) to minimize the possibility of secondary reflection. Screens with a fresnel or ‘etched’

rear surface cannot be used since they require a projector with a zero degree offset lens. The WT600 does not have a

lens, and as stated earlier, the image is projected at a very steep angle (55°).

A diffusion screen with a low gain of approximately 1.0 should be used. A low gain will help to ‘capture’ the image within

the depth of the screen material and not allow much light to pass through and be lost over the viewer’s head, as well as

reduce the amount of hot spotting.

The system will not be as bright as when used with some brighter traditional projectors, and there may be some

minimal hot spotting at the bottom of the screen. However the pros should far outweigh the cons for many users who

need minimal depth in an RP system.

It is also very important that the integrator work with a screen manufacturer who has the expertise in designing an RP

system that will give optimum performance when a WT600 is used within the system.

www.necvisualsystems.com Page 2 of 2

Andere Handbücher für WT600 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere NEC Projektor Handbücher

NEC

NEC NP1150 XGA Bedienungsanleitung

NEC

NEC LT75Z - MultiSync SVGA DLP Projector Bedienungsanleitung

NEC

NEC P452W Bedienungsanleitung

NEC

NEC VE303 Bedienungsanleitung

NEC

NEC MultiSync LT280 Bedienungsanleitung

NEC

NEC GT950 - MultiSync XGA LCD Projector Bedienungsanleitung

NEC

NEC NP-M300X Bedienungsanleitung

NEC

NEC MultiSync MT850 Installations- und Benutzerhandbuch

NEC

NEC UM351W Bedienungsanleitung

NEC

NEC NP305 Bedienungsanleitung

NEC

NEC L102W Bedienungsanleitung

NEC

NEC NP610 Series Bedienungsanleitung

NEC

NEC MultiSync MT1040 Bedienungsanleitung

NEC

NEC LT180 - LT 180 XGA DLP Projector Bedienungsanleitung

NEC

NEC VT595 Series Bedienungsanleitung

NEC

NEC MT1075 Series Bedienungsanleitung

NEC

NEC NP-M271X Bedienungsanleitung

NEC

NEC VT695 Betriebsanleitung

NEC

NEC NP60 - CEILING PLATE Bedienungsanleitung

NEC

NEC HT1000 Series Bedienungsanleitung

NEC

NEC PA600X Series Bedienungsanleitung

NEC

NEC NP3250 Series Bedienungsanleitung

NEC

NEC VT59BE Bedienungsanleitung

NEC

NEC LCDMT850 Installations- und Benutzerhandbuch

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung

Asus

Asus ZenBeam Latte Bedienungsanleitung