nedis BTTC200BK Bedienungsanleitung
ned.is/bttc200bk
Bluetooth® Transmitter
Receiver
provides Bluetooth® connection
to stream audio
BTTC200BK
aQuick start guide 5
cKurzanleitung 11
bGuide de démarrage rapide 17
dSnelstartgids 23
jGuida rapida all’avvio 30
hGuía de inicio rápido 36
iGuia de iniciação rápida 42
eSnabbstartsguide 48
gPika-aloitusopas 54
fHurtigguide 60
2Vejledning til hurtig start 66
kGyors beüzemelési útmutató 72
nPrzewodnik Szybki start 78
xΟδηγό γρήγορη εκκίνηση 84
1Rýchly návod 91
lRychlý návod 97
yGhid rapid de iniiere 103
123456
7 89 qw
A
e r t y
B
5
aQuick start guide
Bluetooth Transmitter Receiver BTTC200BK
For more information see the extended manual online: ned.is/bttc200bk
Intended use
The BTTC200BK is a device that allows you to transmit or receive Bluetooth audio.
The BTTC200BK functions wirelessly with a built-in, rechargeable battery.
The product is not intended for professional use.
Any modification of the product may have consequences for safety, warranty and
proper functioning.
Specications
Product Bluetooth Transmitter Receiver
Article number BTTC200BK
Power supply 5 VDC / 1 A
Battery Lithium-Polymer
Battery capacity 450 mAh
Maximum play time Up to 22 hours
Max. battery charging time Up to 2 hours
Maximum Standby Time Up to 48 hours
Bluetooth® version 5.0
Maximum transmission power 1.31 dBm
Bluetooth frequency range 2402 - 2480 MHz
Bluetooth signal range Up to 10 meters
Bluetooth proles A2DP
Supported codecs SBC / aptXTM, aptXTM Low Latency
6
Connections AUX input/output
SPDIF input
SPDIF output
Micro USB
Main parts (image A)
AUX / SPDIF switch
Volume down / previous track
button
On/off / play / pause button
Volume up / next track button
Bluetooth button
Status indicator LED
Mode switch
AUX port
SPDIF input (Tx)
SPDIF output (Rx)
Micro USB charging port
Main parts (image B)
Stereo audio cable 2x RCA male to
3.5 mm female
3.5 mm to 3.5 mm audio cable
male to male
USB charging cable
SPDIF Optical Audio Cable male
to male
Safety instructions
-
WARNING
• Ensure you have fully read and understood the instructions in this document
before you install or use the product. Keep this document for future reference.
• Only use the product as described in this document.
• Do not use the product if a part is damaged or defective. Replace a damaged
or defective product immediately.
• Do not drop the product and avoid bumping.
7
• This product may only be serviced by a qualified technician for maintenance
to reduce the risk of electric shock.
• Disconnect the product from the power source and other equipment if
problems occur.
• Do not expose the product to water or moisture.
• Do not dismantle, open or shred secondary cells or batteries.
• Do not expose cells or batteries to heat or fire. Avoid storage in direct
sunlight.
• Retain the original product literature for future reference.
• Do not leave a battery on prolonged charge when not in use.
• After extended periods of storage, it may be necessary to charge and
discharge the cells or batteries several times to obtain maximum
performance.
• Batteries contain explosive gases. Prevent contact with flames and sparks.
Provide adequate ventilation during charging.
• Some wireless devices may interfere with implantable medical devices and
other medical equipment, such as pacemakers, cochlear implants and hearing
aids. Consult the manufacturer of your medical equipment for more
information.
• Do not use the product at locations where the use of wireless devices is
prohibited due to potential interference with other electronic devices, which
may cause safety hazards.
Charging the product
1. Connect Btto Aw.
2. Plug the other end of Btinto a 5V/1A USB adapter (not provided).
3. Plug the USB adapter into a power outlet.
A6Burns red to indicate that the product is charging.
4A6switches off when the battery is fully charged.
4When the battery is low, there is a prompt sound and A6blinks red.
8
Switching the product on/o
1. Press and hold A3for 3 seconds to switch the product on or off.
4The product automatically switches off when it is not paired within 10
minutes.
Receiver mode (image C)
Option 1: Using an AUX connection
1. Set the AUX / SPDIF switch A1to AUX.
2. Set the mode switch A7to RX.
3. Plug the 3.5 mm to 3.5 mm audio cable Brinto the AUX A8.
4. Plug the other end of Brinto the audio output device.
4You can also connect an audio device with the stereo audio cable 2x RCA
male to 3.5 mm female Be.
Option 2: Using an SPDIF connection.
1. Set the AUX / SPDIF switch A1to SPDIF.
2. Set the mode switch A7to RX.
3. Plug the SPDIF optical cable Byinto the SPDIF output (Rx) Aq.
4. Plug the other end of Byinto the audio output device.
5. Switch on the product.
Press and hold A4to turn the volume up.
Press and hold A2to turn the volume down.
4A6Blinks blue.
6. Enable Bluetooth on the device you want to pair.
7. Press Bluetooth button A5to start pairing.
8. Select "BTTC200BK" from the list of available Bluetooth devices on your
device.
4If asked, enter the pairing code '0000'.
4A6blinks slowly to indicate pairing is successful.
9
Transmitter mode (image D)
Option 1:
1. Set the AUX / SPDIF switch A1to AUX.
2. Set A7to TX.
3. Plug Brinto A8.
4. Plug the other end of Brinto your audio source.
4You can also connect an audio device with the stereo audio cable 2x RCA
male to 3.5 mm female Be.
Option 2:
1. Set the AUX / SPDIF switch A1to SPDIF.
2. Set A7to TX.
3. Plug Byinto SPDIF input (Tx) A9.
4. Plug the other end of Byinto your audio source.
5. Switch on the product.
A6Blinks green.
6. Keep your Bluetooth audio device within range and switched on.
4Pairing time will vary depending on the device used.
4A6Burns to indicate pairing is successful.
Connect a second device
• After successfully connecting the first device, press A5again to pair to a
second device.
4The devices must be one meter apart from each other.
4The two devices are connected simultaneously.
4If the pairing does not work, switch the product off and on.
Disconnect paired devices
• Press and hold A5for 3 seconds.
4To disconnect a single device, switch off the Bluetooth of that device.
10
To clear the pairing list press and hold A5for 8 seconds.
4A6Blinks twice when cleared.
Recommendations
• When connecting with two devices, use the devices with the same version of
Bluetooth.
• In Bluetooth transmit mode, only headphones and similar devices can be
connected. Smartphones cannot be paired with this mode.
• Do not use this product in a place with obstructions or other Bluetooth
devices to avoid interference.
• When pairing fails, clear the list of paired devices on the product.
Declaration of Conformity
We, Nedis B.V. declare as manufacturer that the product BTTC200BK from our
brand Nedis®, produced in China, has been tested according to all relevant CE
standards and regulations and that all tests have been passed successfully.This
includes, but is not limited to the RED 2014/53/EU regulation.
The complete Declaration of Conformity (and the safety datasheet if applicable)
can be found and downloaded via: nedis.com/BTTC200BK#support
For additional information regarding the compliance, contact the customer
service:
Web: www.nedis.com
E-mail: [email protected]
Nedis B.V., de Tweeling 28
5215 MC ’s-Hertogenbosch, the Netherlands
Inhaltsverzeichnis
Sprachen:
Andere nedis Sender Handbücher
nedis
nedis CATR102BK Bedienungsanleitung
nedis
nedis BTRC110BK Bedienungsanleitung
nedis
nedis CATR122BK Bedienungsanleitung
nedis
nedis BTTR100BK Bedienungsanleitung
nedis
nedis CATR124BK Bedienungsanleitung
nedis
nedis BTTR050BK Bedienungsanleitung
nedis
nedis CATR300BK Bedienungsanleitung
nedis
nedis CATR101BK Bedienungsanleitung
nedis
nedis CATR120BK Bedienungsanleitung
nedis
nedis CATR121BK Bedienungsanleitung
Beliebte Sender Handbücher anderer Marken
Dejero
Dejero EnGo 3x Bedienungsanleitung
Rosemount
Rosemount 4600 Bedienungsanleitung
Speaka Professional
Speaka Professional 2342740 Bedienungsanleitung
trubomat
trubomat GAB 1000 Bedienungsanleitung
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Bedienungsanleitung
Rondish
Rondish UT-11 Bedienungsanleitung
