Nektar WIDIFLEX Bedienungsanleitung
Quick Start Guide
WIDIFLEX
Content
Your WIDIFLEX blister pack contains the following items:
• WIDIFLEX Bluetooth LE MIDI DIN device (output).
• MIDI DIN->1/8” TRS jack adapter cable (input).
• Printed Quite Start Guide (this one)
WIDIFLEX Overview
WIDIFLEX is a Bluetooth LE MIDI DIN adapter which allows
you to send MIDI data to or from electronic MIDI products
equipped with standard MIDI DIN in/out socket. With
WIDIFLEX, you can therefore add Bluetooth MIDI to any
MIDI equipment. For example:
• Connect a standard MIDI keyboard to a Bluetooth
enabled MIDI system, such as devices running iOS or
Android Bluetooth MIDI apps.
• Connect the MIDI in/out on a USB MIDI or MIDI Audio
interface to add Bluetooth MIDI capability to your
computer music system.
• Use as a wireless 2-way MIDI cable by connecting to
another WIDIFLEX or WIDIFLEX USB.
• Group up to 5 WIDI devices to route data from 4
sources to one or from one source to 4.
Connecting to a MIDI Output
• Connect WIDIFLEX to any MIDI equipment with a
standard MIDI out 5-pin DIN jack.
• The WIDIFLEX LED is illuminated when power is on*.
• When the LED is blinking, WIDIFLEX is ready for
pairing.
If another WIDIFLEX is present, the two devices will pair
automatically. To pair with another Bluetooth MIDI device,
activate pairing on that device.
* Most MIDI products supply power via the MIDI out jack,
but not all. For more info, check:
www.nektartech.com/support/WIDI
Connecting to a MIDI Input
WIDIFLEX can send and receive MIDI messages at the same
time. Perform on a synth, record and then playback to the
synth, is now possible wirelessly.
To setup the MIDI input, make sure WIDIFLEX is connected
and paired correctly, as described in the section ‘Connecting
to a MIDI Output’. Next, connect the MIDI input:
• Locate the adapter cable in the WIDIFLEX blister pack
and connect the 1/8” TRS jack to the 1/8” input jack on
WIDIFLEX. You can unplug WIDIFLEX if necessary.
• Connect the adapter cable’s 5-pin
DIN connector to the MIDI input
on the receiving MIDI device.
• Send MIDI data to WIDIFLEX and
check the WIDIFLEX LED blinks, to
indicate MIDI messages are received.
Note: WIDIFLEX receives power from the MIDI output jack.
This means WIDIFLEX cannot be connected to an input only.
TO: MIDI Out MIDI In
The WIDI App
The WIDI app (CME PTE Ltd) can be downloaded from the
Apple App Store or Google Play. With the app, you can:
• Update the WIDIFLEX rmware.
• Create groups with up to 5 WIDI devices each.
Once set up, a group of WIDI devices allows setup of routing
congurations. For example, from one WIDI device to
multiple
WIDI devices or from multiple WIDI devices to one.
Manually Activate New Pairing
An existing pairing can be manually terminated and new
paring established.
• Locate the button on the opposite side from the 1/8”
jack connector.
• With WIDIFLEX on and paired, press and hold the
button for 3 seconds, then release.
• The LED start’s blinking and WIDIFLEX is ready for a new
pairing.
Restore Factory Settings
If WIDIFLEX is not working correctly, a factory restore may
resolve any issues.
• Located the button on the opposite side from the 1/8”
jack connector.
• With WIDIFLEX o (i.e. the MIDI product it’s plugged in
to is powered o), press and hold the button.
• Switch the MIDI product on to supply power.
• Wait for the WIDIFLEX LED to blink 3 times, then re-
lease the button.
For troubleshooting and further information, go to:
www.nektartech.com/support/WIDI
Declaration of Conformity
European Union
WIDIFLEX has been tested to meet or exceed Emissions and
Immunity requirements according to European Standards EN 55035,
EN55032, EN61000-3-2, EN61000-3-3, EN 300 328, EN 62479 and
EN 301 489. WIDIFLEX is in conformity with the provisions of EMC
Directive 2014/30/EU.
United States
WIDIFLEX has been tested to comply with FCC regulations Part 15,
SubPart B, Class B, test method ANSI C63.4: 2014.
Contains FCC ID: 2ABRUBDLEM205
Dispose of product securely, avoiding exposure to food sources and ground water. Only use the
product in accordance with the instructions.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interfer-
ence will not occur in a Particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
United Kingdom
WIDIFLEX has been tested to comply with UK emissions and
immunity regulations. A declaration of conformity can be obtained
by contacting Nektar Technology (UK) via email:
Andere Nektar Adapter Handbücher
