Ness HTA 100 Leitfaden

Installation and Assembly: Articulating Wall Arm for LCD screens

Model: HTA100

Tools Needed for

Assembly

Stud finder

("edge to edge"

stud finder is

recommended)

Installation to

Wood Stud Wall

Phillips

screwdriver

Drill with 1/4" and 5/32" drill bits

Important

Do not begin to install your mount product until you have read and understood the instructions.

This product should only be installed by someone of good mechanical aptitude, has experience with basic building construction, and fully understands these

Instructions. Consult a qualified professional installer if unsure.

Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.

Never exceed the Maximum Load Capacity of 30 lbs.

If mounting to wood wall studs, mke sure that mounting screws are anchored into the center of the studs. Use of an “edge to edge” stud finder is highly

Recommended.

Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

Tighten screws firmly, but does not overtighten.Overtightening can damage the items, greatly reducing their holding power.

Using a stud finder, locate and mark the edges of the wood stud used in

mounting this product. Use of an edge to edge stud finder is highly

recommended. Use of level to draw a vertical line down the center of the

stud. Use wall plate as template to mark center of holes along the

vertical line. Drill two 5/32" (4mm) diaphones 2.5"(65mm) deep. Attach

wall arm assembly (AA) to wall using two #14x2.5" flat head wood

screws (D).

FOR VESA 75 MOUNTING PATTERN:

Choose whole pattern as shown below. Attach Wall arm assembly (AA) to back of screen using four M4x14mm screws (A).

Note: If whole Patten is in a pocket, attach wall arm assembly (AA) to back of screen using four M4x25mm screws (B) and four spacers (C).

FOR VESA 100 MOUNTING PATTERN:

Choose whole pattern as shown below.

Attach Wall arm assembly (AA) to

Back of screen using four M4x14mm

Screws (A).

If more or less tension is desired in the arm pivot points, do the following:

To increase tension, turn socket screw clockwise with 4mm Allen wrench (E) or 5mm Allen wrench (F).

To reduce tension, turn socket screw counter-clockwise with 4mm Allen wrench (E) or 5mm Allen

Important

Make sure that the supporting surface will safely

support the combined load of the equipment and

all attached hardware and components.

Important

Tighten screws so that wall plate is firmly attached,

but do not overtighten.Overtightening can damage

the screws, greatly reducing three holding power.

Never tighten in excess of 80 lbs.

Make sure that mounting screws are anchored into

the center of the studs. The use of an “edge to edge”

stud finder is highly recommended.

Important

If screws don’t get three complete turns in the screen inserts or if screws bottom out and

wall arm assembly is still not tightly secured, damage may occur to screen or product

may

Parts List

Description ty. Part#

AA Wall arm

assembly 1

095-0358-S

A M4x.7x14m

m phillips screw 4

520-2239

B M4x.7x25mm phillips screw

504-2015

C 437H spacer

590-5003

D #14x2. 5”flat head wood screw

520-2165

E 4 mm alle

n wrench 1

560-9706

F 5 mm allen wrench

560-9640

G concrete anchor

590-0097

fig. 2.1

Wrench (F).Do not turns more than half a turn.

Installation to Solid Concrete and Cinder Block

Level and use wall plate as template to mark center of

holes.

Drill two 1/4" (6mm) dial, holes to a minimum depth of 2.5"

(65mm).Insert anchors (G) in holes flush with wall. Place wall arm assembly

(AA) over anchor and secure with wood screws (D).Make sure wall arm is level,

and tighten all fasteners.

Important

When installing mount wall mount on cinder block, verify that you have a minimum of 1-

3/8” of actual concrete thickness in the hole to be used for the concrete anchors. Do not

drills into mortar joints Be sure to mount in a solid part of the block, generally 1”

minimum from the side of the block? Cinder block must meet ASTM C-90 specifications.

It is suggested that a standard electric drill on slow setting is used to drill the hole instead

of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity.

Concrete must be 2000 phi density minimum. Lighter density concrete may not hold concrete

Anchor.

Mark sure that the wall will safely support the combined load of the equipment and all

attached

Hardware and components

Andere Ness Rack & Stand Handbücher

Ness

Ness X Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung