NetApp AFF A400 Bedienungsanleitung

AFF A400 systems

ONTAP Systems

NetApp

November 23, 2021

This PDF was generated from https://docs.netapp.com/us-en/ontap-systems/a400/install-setup.html on

November 23, 2021. Always check docs.netapp.com for the latest.

Table of Contents

AFF A400 System Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê1

Install and setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê1

Maintain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê13

AFF A400 System Documentation

Install and setup

Start here: Choose your installation and setup experience

For most configurations, you can choose from different content formats.

•Quick steps

A printable PDF of step-by-step instructions with live links to additional content.

•Video steps

Video step-by-step instructions.

•Detailed steps

Online step-by-step instructions with live links to additional content.

For MetroCluster configurations, see either:

•Install MetroCluster IP configuration

•Install MetroCluster Fabric-Attached configuration

Quick guide - AFF A400

This guide gives graphic instructions for a typical installation of your system from racking

and cabling, through initial system bring-up. Use this guide if you are familiar with

installing NetApp systems.

Access the Installation and Setup Instructions PDF poster:

AFF A400 Installation and Setup Instructions

Videos - AFF A400

There are two videos; one showing how to rack and cable your system and one showing

an example of using the System Manager Guided Setup to perform initial system

configuration.

Video one of two: Hardware installation and cabling

The following video shows how to install and cable your new system.

AFF A400 Installation and setup instructions AFF A400 Installation and setup instructions

Video two of two: Perform end-to-end software configuration

The following video shows end-to-end software configuration for systems running ONTAP 9.2 and later.

NetApp video: Software configuration for vSphere NAS datastores for FAS/AFF systems running ONTAP 9.2

Detailed guide - AFF A400

This guide gives detailed step-by-step instructions for installing a typical NetApp system.

Use this guide if you want more detailed installation instructions.

Step 1: Prepare for installation

To install your system, you need to create an account, register the system, and get

license keys. You also need to inventory the appropriate number and type of cables for

your system and collect specific network information.

Before you begin

You need to have access to the Hardware Universe for information about site requirements as well as

additional information on your configured system. You might also want to have access to the Release Notes for

your version of ONTAP for more information about this system.

NetApp Hardware Universe

Find the Release Notes for your version of ONTAP 9

You need to provide the following at your site:

•Rack space for the storage system

•Phillips #2 screwdriver

•Additional networking cables to connect your system to your network switch and laptop or console with a

Web browser

Steps

1. Unpack the contents of all boxes.

2. Record the system serial number from the controllers.

3. Inventory and make a note of the number and types of cables you received.

The following table identifies the types of cables you might receive. If you receive a cable not listed in the

table, see the Hardware Universe to locate the cable and identify its use.

NetApp Hardware Universe

Type of cable… Part number and length Connector type For…

100 GbE cable

(QSF(28)

X66211A-05 (112-00595), 0.5m

X66211A-1 (112-00573), 1m

X66211A-2 (112-00574), 2m

X66211A-5 (112-00574), 5m

Storage, cluster interconnect/HA,

and Ethernet data (order-

dependent)

25 GbE cable

(SFP28s)

X66240-2 (112-00598), 2m

X66240-5 (112-00639), 5m

GbE network connection (order-

dependent)

32 Gb FC

(SFP+ Op)

X66250-2 (112-00342), 2m

X66250-5 (112-00344), 5m

X66250-15 (112-00346), 15m

FC network connection

Storage Cables X66030A (112-00435), .5m

X66031A (112-00436), 1m

X66032A (112-00437), 2m

X66033A (112-00438), 3m

mini-SAS HD to mini-SAS HD

cables (order-dependent)

Optical cables X66250-2-N-C (112-00342) 16 Gb FC or 25GbE cables for

mezzanine cards (order-

dependent)

RJ-45 (order

dependent)

X6585-R6 (112-00291), 3m

X6562-R6 (112-00196), 5m

Management network

Micro-USB

console cable

Not applicable Console connection used during

software setup if laptop or console

does not support network

discovery.

Power cables Not applicable Powering up the system

4. Review the NetApp ONTAP Configuration Guide and collect the required information listed in that guide.

ONTAP Configuration Guide

Step 2: Install the hardware

You need to install your system in a 4-post rack or NetApp system cabinet, as applicable.

1. Install the rail kits, as needed.

2. Install and secure your system using the instructions included with the rail kit.

You need to be aware of the safety concerns associated with the weight of the system.

3. Attach cable management devices (as shown).

4. Place the bezel on the front of the system.

Step 3: Cable controllers to your network

You can cable the controllers to your network by using the two-node switchless cluster

method or by using the cluster interconnect network.

Option 1: Cable a two-node switchless cluster

The optional data ports, optional NIC cards, and management ports on the controller

modules are connected to switches. The cluster interconnect and HA ports are cabled on

both controller modules.

You must have contacted your network administrator for information about connecting the system to the

switches.

Be sure to check the direction of the cable pull-tabs when inserting the cables in the ports. Cable pull-tabs are

up for all onboard ports and down for expansion (NIC) cards.

As you insert the connector, you should feel it click into place; if you do not feel it click, remove

it, turn it around and try again.

Steps

1. Use the animation or illustration to complete the cabling between the controllers and to the switches:

Two-node switchless cluster cabling

2. Go to Step 4: Cable controllers to drive shelves for drive shelf cabling instructions.

Option 2: Cable a switched cluster

The optional data ports, optional NIC cards, mezzanine cards, and management ports on

the controller modules are connected to switches. The cluster interconnect and HA ports

are cabled on to the cluster/HA switch.

You must have contacted your network administrator for information about connecting the system to the

switches.

Be sure to check the direction of the cable pull-tabs when inserting the cables in the ports. Cable pull-tabs are

up for all onboard ports and down for expansion (NIC) cards.

As you insert the connector, you should feel it click into place; if you do not feel it click, remove

it, turn it around and try again.

Steps

1. Use the animation or illustration to complete the cabling between the controllers and to the switches:

Switched cluster cabling

2. Go to Step 4: Cable controllers to drive shelves for drive shelf cabling instructions.

Step 4: Cable controllers to drive shelves

You can cable either NSS224 or SAS shelves to you system.

Option 1: Cable the controllers to a single drive shelf

You must cable each controller to the NSM modules on the NS224 drive shelf.

Be sure to check the illustration arrow for the proper cable connector pull-tab orientation. The cable pull-tab for

the NS224 are up.

As you insert the connector, you should feel it click into place; if you do not feel it click, remove

it, turn it around and try again.

Steps

1. Use the following animation or illustration to cable your controllers to a single drive shelf.

Cabling the controllers to one NS224 drive shelf

2. Go to Step 5: Complete system setup and configuration to complete system setup and configuration.

Option 2: Cable the controllers to two drive shelves

You must cable each controller to the NSM modules on both NS224 drive shelves.

Be sure to check the illustration arrow for the proper cable connector pull-tab orientation. The cable pull-tab for

the NS224 are up.

As you insert the connector, you should feel it click into place; if you do not feel it click, remove

it, turn it around and try again.

Steps

1. Use the following animation or illustration to cable your controllers to two drive shelves.

Cabling controllers to two NS224 drive shelves

2. Go to Step 5: Complete system setup and configuration to complete system setup and configuration.

Option 3: Cable the controllers to SAS drive shelves

You must cable each controller to the IOM modules on both SAS drive shelves.

Be sure to check the illustration arrow for the proper cable connector pull-tab orientation. The cable pull-tab for

the DS224-C are down.

Andere Handbücher für AFF A400

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere NetApp Lagerung Handbücher

NetApp

NetApp AFF A900 Handbuch

NetApp

NetApp DE6600 Bedienungsanleitung

NetApp

NetApp FAS22 Series Bedienungsanleitung

NetApp

NetApp FAS8200 Series Bedienungsanleitung

NetApp

NetApp AFF A200 Bedienerhandbuch

NetApp

NetApp H410S Handbuch

NetApp

NetApp FAS500f Bedienungsanleitung

NetApp

NetApp StorageGRID Webscale SG5700 Series Betriebsanleitung

NetApp

NetApp EF550 Bedienungsanleitung

NetApp

NetApp DiskShelf14mk4 FC Bedienungsanleitung

NetApp

NetApp AFF A250 Bedienungsanleitung

NetApp

NetApp E5700 Bedienungsanleitung

NetApp

NetApp FAS2700 Series Bedienungsanleitung

NetApp

NetApp SOLIDFIRE Bedienungsanleitung

NetApp

NetApp FAS2800 Handbuch

NetApp

NetApp StorageGRID Webscale SG5700 Series Betriebsanleitung

NetApp

NetApp FAS26 Series Handbuch

NetApp

NetApp EF550 Bedienungsanleitung

NetApp

NetApp E-Series 3040 40U Bedienungsanleitung

NetApp

NetApp FAS8300 Bedienungsanleitung

NetApp

NetApp FAS8300 Bedienungsanleitung

NetApp

NetApp AFF A320 Bedienungsanleitung

NetApp

NetApp AFF A800 Bedienungsanleitung

NetApp

NetApp AFF A400 Handbuch

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

HP P9000 Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung