NetComm NB1300 Bedienungsanleitung
www.netcomm.com.au Rev. 2 - YML643
Page 2 NB1300 ADSL Modem
Contents
Introduction ....................................................................................................................3
Which configuration is best? ........................................................................... 3
Package Contents ........................................................................................... 4
Factory Defaults ............................................................................................... 4
Do I need a Micro filter? ................................................................................... 5
Ethernet Gateway Configuration ................................................................................... 6
Step 1: Connecting your computer to the NB1300......................................... 6
Step 2: Configuring the NB1300..................................................................... 7
Step 3: Configuring your Computer to use the NB1300 ................................ 9
Ethernet Modem (Bridge) Configuration ..................................................................... 10
Step 1: Connecting your computer to the NB1300....................................... 10
Step 2: Configuring the NB1300....................................................................11
Step 3: Configuring your Computer/Router to use the NB1300 .................. 12
USB Gateway (Router) Configuration ......................................................................... 13
Step 1: Connecting your computer to the NB1300....................................... 13
Step 2: Configuring the NB1300................................................................... 14
Step 3: Configuring your Computer to use the NB1300 .............................. 15
Trouble Shooting ......................................................................................................... 16
Resetting the NB1300 ADSL Modem............................................................ 16
Registering your NetComm Product........................................................................... 16
Contact Information ....................................................................................... 16
Trademarks and Notices............................................................................... 16
Warranty Registration Form .......................................................................... 17
Product Warranty............................................................................................ 19
Limitations of Warranty .................................................................................. 19
Rev. 2 - YML643 www.netcomm.com.au
NB1300 ADSL Modem Page 3
Introduction
This guide is supplied to help you connect your NB1300 ADSL Modem quickly to your
network or Windows computer.
If the NB1300 has already been used, we strongly recommend you reset and flush all settings of
the unit via the USB cable by pressing and holding the RESET button on the rear of the modem
for 10 seconds. Wait for the RDY light to begin pulsing before continuing.
Note: Please be aware that connection via USB is only supported in Windows 98SE,
Windows Me, Windows 2000 and Windows XP. For Windows 95, NT, Linux and
Macintosh you should use the Ethernet port of your NB1300.
Which configuration is best?
Your NB1300 ADSL Modem can be connected and configured in various ways, below is a
description of the most common modes of operation.
Ethernet Gateway (Router) - This is when the NB1300 is connected to your network switch
or hub and shares the Internet connection to all computers on the network. The NB1300 will log
on to your ISP on behalf of your computers and it will shield your computers from direct
Internet attack by using Network address Translation (NAT).
Ethernet Modem (Bridge) - This is when you plug the modem directly into the Ethernet port
of just one computer or another router (via a cross over Ethernet cable) you then must run
Internet connection software (often supplied by your ISP) on the computer or second router to
establish a connection to the Internet. This method means that the computer or router connected
to the Ethernet port of the NB1300 is exposed to the Internet and is given a public IP address.
USB Gateway (Router) - If you do not have an Ethernet port on your computer you can use
your USB port like an Ethernet port to connect to the NB1300. This "simulated" Ethernet port
is only for connecting to the NB1300 and is only available for Windows 98SE, Windows 2000
and Windows XP. The NB1300 will log on to your ISP on behalf of your computer and it will
shield your computer from Internet attack by using NAT. Note that the USB cable is not
supplied with the NB1300.
If you wish to configure the NB1300 in a different way to the examples above you should
consult a Network Specialist for more information.
Note: We recommend you change your Router’s password from the factory default
before connecting it to a network or the Internet. Refer to the “Admin Password”
section in the “Security” Menu.
This unit should only be connected to the Telecommunications Network through a
line cord which meets the requirements of ACA TS008.
www.netcomm.com.au Rev. 2 - YML643
Page 4 NB1300 ADSL Modem
Package Contents
The following items should be contained in your NB1300 ADSL Modem Package:
■Quick Start Guide
■ADSL Modem (NB1300)
■Power adaptor (12V AC / 1Amp)
■Telephone line cable (RJ11)
■Crossover network cable (RJ45)
■NetComm Communications CD-ROM (CRS767)
■USB Cable
Factory Defaults
The following table lists the Factory Defaults of your NB1300 ADSL Modem:
Field Setting Details
LANIPaddress: 192.168.1.1
LAN Subnet Mask: 255.255.255.0
DHCP Server: Enabled (pool 192.168.1.100 - 192.168.1.149)
User Name: admin
Password: password
Main Function: Router (Bridge Disabled)
WAN connection type: PPPoE LLC
VPI: 8
VCI: 35
Note: These defaults may change with firmware updates and factory changes please
consult the NetComm website to check for the latest defaults.
Rev. 2 - YML643 www.netcomm.com.au
NB1300 ADSL Modem Page 5
Do I need a Micro filter?
Micro filters are used to prevent common telephone equipment, such as phones, answering
machines and fax machines, from interfering with your ADSL service. If your ADSL enabled
phone line is being used with any other equipment other than your ADSL Modem then you will
need to use one Micro filter for each phone device.
Splitters may be installed when your ADSL line is installed or when your current phone line is
upgraded to ADSL. If your telephone line is already split you will not need to use a Microfilter
- check with your ADSL service provider if you are unsure.
Each micro filter is connected in-line with your telephone or fax machine so that all signals pass
through it. Telephones and/or facsimiles in other rooms that are using the same extension will
also require Microfilters. The following diagram gives an example of connecting your ADSL
Modem/Router using a Microfilter.
A suitable Microfilter can be purchased from NetComm or your Service Provider, if required.
www.netcomm.com.au Rev. 2 - YML643
Page 6 NB1300 ADSL Modem
Ethernet Gateway Configuration
Before continuing, ensure you have the following items and information ready:
■A Windows 98, ME, NT, 2000 or XP client machine with a Network Interface Card
installed.
■Either a Network Hub and two UTP cables OR one Crossover UTP cable.
■A telephone line with ADSL service enabled.
■User Name, Password, VPI, VCI, encapsulation and DNS server settings for your ADSL
account (ask your ISP if unsure) .
Note: The following procedure presumes your NB1300 is set to a factory default IP
address 192.168.1.1.
Step 1: Connecting your computer to the NB1300
■Using either a hub and two UTP cables, or just one crossover UTP cable, connect the
NB1300 Modem Router to your computer.
■Connect one end of the ADSL phone line to the NB1300 ADSL Modem and the other end
to the wall socket.
■Connect the power pack to the NB1300 ADSL Modem and switch on the power switch.
■Ensure that there is a LAN link light on the NB1300.
■Ensure that the computer you intend to use has an IP address in the same subnet as the
NB1300 ADSL Modem. (e.g. the NB1300’s default IP is 192.168.1.1 - your computer
should be on 192.168.1.100 or similar.) If you have DHCP enabled on your computer, the
NB1300 will assign your computer a suitable IP address.
■Ensure that your computer has a LAN link light.
Rev. 2 - YML643 www.netcomm.com.au
NB1300 ADSL Modem Page 7
Step 2: Configuring the NB1300
1. After connecting all the ADSL Router cables, powering on the ADSL Router, and launching
a web browser, such as Internet Explorer or Netscape Navigator, browse to the address
http://192.168.1.1.
2. Enter the correct user name and password to access the Configuration tool. The default user
name and password are as below.
User Name : admin
Password: password
Note: You must click the Submit button on every page that you make changes on and
when you have made all your changes click the Save Setting and Reboot button
from the bottom of the menu.
3. Click on the One Page Setup link under the Basic menu. You do not need to change the
LAN settings unless you need the NB1300 to work with an existing network on a subnet
other than 192.168.1.x.
You will need to Change your WAN and VC settings as provided by your ISP. The following
lists an example of the most common ISP settings used in Australia. The fields that require
changing from the default settings are highlighted.
www.netcomm.com.au Rev. 2 - YML643
Page 8 NB1300 ADSL Modem
Field Setting Details
Service name: Any name to describe your ISP
User Name: Your ISP will provide a case sensitive User Name in a
format similar to your email address. Contact your ISP
for details
Password: Enter your Password as supplied by your Service
Provider (characters are usually all lower case)
Disconnect timeout: 0 ❖
Mode/Wan Connection Type: PPPoE LLC or PPPoA
VPI: 8 ❖
VCI: 35 ❖
Static IP Address: 192.168.241.101 ❖
Subnet Mask: 255.255.255.0 ❖
Default Gateway: 0.0.0.0 ❖
Bridge mode: Disabled ❖
❖
Default Setting. Although in most cases you will not be required to alter these
default settings for your NB1300, your ISP may identify specific settings to enable
connection to their service. Please refer to your ISP or Network Administrator for
further information.
4. Click Submit and then click the Save Setting and Reboot button from the bottom of the
menu. Wait for the configuration to complete.
Standard configuration of your NetComm NB1300 ADSL Modem is now complete. You
should be able to access the Internet through the unit, when it is set to be your gateway on
your computer/s. Refer to Step 3 for more information.
Rev. 2 - YML643 www.netcomm.com.au
NB1300 ADSL Modem Page 9
Step 3: Configuring your Computer to use the NB1300
To use the NB1300 ADSL Modem to access the Internet, your computer must have an IP
Address that is in the same LAN subnet as the NB1300 ADSL Router and use the NB1300
ADSL Router’s IP address as its gateway.
Most applications call for the Primary and Secondary DNS server entries to be made on each
computer. These can be automatically assigned by another DHCP server or by enabling the
DHCP server on the NB1300 ADSL Modem, and entering the DNS values in the DNS section
of the NB1300.
The following example shows how a computer could be set up when the NB1300 ADSL
Modem is configured with no DHCP service for this example. The NB1300 ADSL Modem
would be set to a LAN IP Address (Gateway) of 192.168.1.1 with a Subnet Mask of
255.255.255.0
Open the Control Panel and double click on the Network icon. Scroll down to select
TCP/IP-> Ethernet Card and click on the Properties button.
Note: When using Internet Explorer as a web
browser, click on the “Tools” menu and select
“Internet Options”. Select the “Connections”
tab and click on the “LAN Settings” button.
Tick the “Automatically detect settings”
checkbox and make sure the “Use a Proxy
server” checkbox is unchecked.
Your DNS numbers are
specific to your ISP and
should be notified along
with your User Name and
Password.
www.netcomm.com.au Rev. 2 - YML643
Page 10 NB1300 ADSL Modem
Ethernet Modem (Bridge) Configuration
Before continuing, ensure you have the following items and information ready:
■A computer with a Network Interface Card installed or a router (such as the NetComm
NB3100).
■A Crossover UTP cable.
■A telephone line with ADSL service enabled.
■User Name, Password, VPI, VCI, encapsulation and DNS server settings for your ADSL
account (ask your ISP if unsure). These are not needed for the NB1300, but are required for
the computer or router that it will be connected to.
Note: The following procedure presumes your NB1300 is set to a factory default IP
address 192.168.1.1.
Step 1: Connecting your computer to the NB1300
■Using a Crossover network cable, connect the Ethernet port of the NB1300 into the Ethernet
port of the computer you wish to use to configure the unit.
■Connect the power and switch the NB1300 on.
■Ensure the LAN link on the NB1300 is active.
■Configure your Computer to use any IP address in the range of 192.168.1.2 to
192.168.1.254.
Note: When the NB1300 is used in Bridge mode it is a fairly passive device and most
Internet configuration required (such as User Name, Password, etc.) is done on the
computer or another router.
Andere Handbücher für NB1300
4
Inhaltsverzeichnis
Andere NetComm Modem Handbücher
NetComm
NetComm NF18ACV Bedienungsanleitung
NetComm
NetComm NTC-100 Bedienungsanleitung
NetComm
NetComm AM5066 Bedienungsanleitung
NetComm
NetComm NB1200 Bedienungsanleitung
NetComm
NetComm NP7042 Bedienungsanleitung
NetComm
NetComm PlayStation 3 NB16WV-02 Bedienungsanleitung
NetComm
NetComm AM5065 Bedienungsanleitung
NetComm
NetComm NB3 Bedienungsanleitung
NetComm
NetComm N3GS003 Bedienungsanleitung
NetComm
NetComm NF8AC Bedienungsanleitung
NetComm
NetComm NB1300Plus4 Bedienungsanleitung
NetComm
NetComm NTC-3000 Series Bedienungsanleitung
NetComm
NetComm CD2004 Mega-i-Modem Bedienungsanleitung
NetComm
NetComm CD2004 Mega-i-Modem Bedienungsanleitung
NetComm
NetComm NB14WN Bedienungsanleitung
NetComm
NetComm AM5066 Bedienungsanleitung
NetComm
NetComm NB5580W Bedienungsanleitung
NetComm
NetComm Roadster Series Bedienungsanleitung
NetComm
NetComm NB100 Bedienungsanleitung
NetComm
NetComm NB11W Bedienungsanleitung
Beliebte Modem Handbücher anderer Marken
Davicom
Davicom DM562AP Bedienungsanleitung
EpiValley
EpiValley TATA indicom SXC-1080 Bedienungsanleitung
Zte
Zte WiMAX Bedienungsanleitung
Intelimax
Intelimax MA-2060 Bedienungsanleitung
SMC Networks
SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch
Telstra
Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung
US Robotics
US Robotics 3453C Bedienungsanleitung
MaxTech
MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung
Zte
Zte MF823 Bedienungsanleitung
Four-Faith
Four-Faith F1403 Bedienungsanleitung
Sierra Wireless
Sierra Wireless AIRLINK MP595W Bedienungsanleitung
Gemtek
Gemtek WiMAX WIXFBR-103 Bedienungsanleitung