4
4Finally, Verify Wireless Network Connectivity
a. Verify that the status monitor information at the bottom of the utility matches
your wireless network.
b. Check the color of the WG111 icon in the Windows system tray: green or
yellow indicates a working connection; red indicates no connection.
c. Check the WG111 LED: blinking means attempting to connect; solid indicates
a good connection; off means the WG111 is not plugged in.
d. Verify connectivity to the Internet or network resources.
Note: If you are unable to connect, see the Troubleshooting Chapter of the
Reference Manual on the Resource CD.
Windows 2000, Me, or 98SE
1
1First, Install the WG111 Software
Note: Windows 2000 may require you to be logged on with administrator rights.
a. Power on your PC, let the operating system boot up completely, and log in
as needed.
b. Insert the Resource CD for the WG111 into your CD-ROM drive. The CD
main page shown below will load.
c. Click the Install Driver & Utility link.
d. Follow the InstallShield Wizard steps. You will be prompted to choose the
country you are located in.
e. Click Finish when done, and if prompted restart your computer.
*201-10153-01*
201-10153-01 May 2004
©2004 NETGEAR, Inc. NETGEAR, the Netgear logo, Everybody's connecting, ProSafe and Auto Uplink are
trademarks or registered trademarks of Netgear, Inc. in the United States and/or other countries. Microsoft and
Windows are registered trademarks of Microsoft Corporation in the United States and/or other countries. Other
brand and product names are trademarks or registered trademarks of their respective holders. Information is sub-
ject to change without notice. All rights reserved.
2
2Next, Install the WG111 54 Mbps Wireless USB 2.0 Adapter
a. Locate an available USB port on your PC. Connect the USB cable to the
WG111 and insert the other end of the cable into the USB slot on your PC.
b. After a short delay, the Found New Hardware Wizard displays. Select Install the
software automatically (Recommended) and click Next.
c. Follow the Found New Hardware Wizard steps, click Finish when done, and if
prompted, restart your computer.
d. Next, you will be prompted to choose the country where you are located. Select
your location from the list.
You will now see the WG111 system tray icon in the lower right area of
the Windows task bar.
3
3Now, Configure Your WG111 and Save the Profile
a. Open the WG111 Smart Wireless Settings Utility by clicking on the icon in the
Windows system tray.
The utility opens to the Settings tab page.
b. Change the Network Name SSID to match your network.
Tip: To view the available wireless networks, use the drop-down list or the
Networks tab and choose the one you want.
c. Click Apply to activate the connection.
Tip: Create work and home profiles. Then, activate whichever one you need for
your current location.
Note: The status bar at the bottom of the utility reports the speed of your connection.
108 Mbps speed is only possible when your wireless network has a 108 Mbps access
point such as in the NETGEAR WGT624 108 Mbps Wireless Firewall Router.
4
4Finally, Verify Wireless Network Connectivity
a. Verify that the status monitor information at the bottom of the utility matches
your wireless network.
b. Check the color of the WG111 icon in the Windows system tray: green or
yellow indicates a working connection; red indicates no connection.
c. Check the WG111 LED: blinking means attempting to connect; solid indicates
a good connection; off means the WG111 is not plugged in.
d. Verify connectivity to the Internet or network resources.
Note: If you are unable to connect, see the Troubleshooting Chapter of the
Reference Manual on the Resource CD.
Technical Support
PLEASE REFER TO THE SUPPORT INFORMATION CARD THAT SHIPPED
WITH YOUR PRODUCT.
By registering your product at www.NETGEAR.com/register, we can provide you with
faster expert technical support and timely notices of product and software upgrades.
Attention: This device may be used throughout the European
community. Some restrictions may apply in France and Italy.
!
0560
Note: If Windows 2000
displays a Digital
Signature Not Found
warning, click Yes to
continue the installation.
