NETGEAR CG814W Bedienungsanleitung

Netgear CG814W Wireless Cable Modem Gateway

Netgear CG814W

Wireless Cable Modem Gateway

Quick Guide

Windows, and the Windows logo are registered trademarks

of Microsoft Corporation. All other trademarks and brand

names are the property of their respective proprietors.

FCC STATEMENT

The Netgear CG814W has been tested and complies with the

specifications for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interface in a

residential installation. This equipment generates, uses, and

can radio frequency energy and, if not installed and used

according to the instructions, may cause harmful interference

to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or

television reception, which is found by turning the equipment

off and on, the user is encouraged to try to correct the

interference by one or more of the following measure:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment of devices

• Connect the equipment to an outlet other than the receiver

• Consult a dealer or an experienced radio/TV technician for

assistance

Netgear CG814W Wireless Cable Modem Gateway

Table of Contents

Netgear CG814W Wireless Cable Modem Gateway

Chapter 1: Introduction

Overview

Thank you for purchasing the Netgear CG814W Wireless Cable Modem

Gateway. The Netgear CG814W provides the ideal solution for connecting

your wireless network to a high-speed broadband Internet connection and a

10/100 Fast Ethernet backbone. Configurable as a DHCP server for your

existing network, the Netgear CG814W acts as the only externally recognized

Internet gateway on your local area network (LAN) and serve as an Internet

NAT firewall against unwanted outside intruders. The Netgear CG814W can

also be configured to filter internal users’ access to the Internet.

A typical gateway relies on a hub or a switch to share its Internet connection,

but the Netgear CG814W channels this connection through the blazing, full

duplex of its built-in 10/100 4-Port Switch. This cutting-edge combination of

wireless router and switch technology eliminates the need to buy an additional

hub or switch and extends the range of your wireless network. Now your entire

wireless network can enjoy blazing broadband Internet connections supported

by its robust switched backbone. With the dual-function speed and power of

the Netgear CG814W, your network will take off at speeds faster than you ever

imagined possible.

Software Features

DOCSIS Features

 Cable Modem (CM) is 1.0 and 1.1 upgradeable

 Concatenation, Fragmentation, Payload Header suppression, IGMP

and BPI and BPI Plus are supported features for DOCSIS 1.1

 4/16/32/64/128/256/512/1024 QAM Downstream Receiver

 2/4/8/16/32/64/128/256 QAM Advanced TDMA Upstream Transmitter

 Both IP and LLC filters are supported

 Sixteen (16) destination address filters and 256 multicast/unicast DA

filters

 Sixteen (16) independent upstream queues for multiple QoS support

Netgear CG814W Wireless Cable Modem Gateway

USB Features

 OS (Win2K, XP, WinME) supported for USB interface

Wireless Features

 Supports at least one beacon/DTIM interval of within the range

20-1000κμs

 Supports reception of fragmented packets

 Supports reception of RTS and generation of CTS

Firewall Features

 Stateful Packet Inspection against both Denial of Service and

Distributed Denial of Service attacks and will protect against the

following:



Reassembly attacks



SYN Attack (SYN Flood)



ICMP Flood



Ping of Death Attack



Tear Drop Attack



IP Spoofing Attack



LAND Attack



Jolt



Winnuke Attack (Netbios out-of-bound)



OverDrop



BONK, BOINK



Blind Spoofing



Echo/Chargen



Storm



Smurf Attack



Mime Flood

 De-Militarized Zone (DMZ) which allows a computer on the LAN to

expose all of its ports to the WAN that are not otherwise filtered

 Logged Events which all security incidents will be logged

 Keyword blocking is based on keywords in a URL and can be

specified by the user

Netgear CG814W Wireless Cable Modem Gateway

NAT Requirements

The implementation of NAT must allow for specific port redirection. Listed

below are applications supported.



FTP



IRC



H.323



Quake



Blizzard games



Chat ALG



Real Audio/Video



CUSEEME



Netmeeting



MS Games but not with game zone



DIABOLO II



Activision Games



PCAnywhere



SSL



NNTP

 Port Forwarding, incoming traffic that is not part of an existing

connection will be dropped unless the user specifies forwarding of the

server to a host on the LAN

Virtual Private Network (VPN) Feature

 Having the ability to enable or disable PPTP and IPSec pass through

Minimum Requirements

One RJ-45 Broadband Internet connection, with a Cable Modem



One PC with an installed 10Mbps, 100Mbps, or 10/100 Mbps Ethernet

card (optional)

TCP/IP network protocol for each PC

UTP network cable with RJ-45 connector

Microsoft Internet Explorer 4.0 or later, or Netscape Navigator 4.0 or later.

(5.0 and 4.7, respectively, are strongly recommended.)

Windows 95, 98, Millennium, NT 4.0, 2000 or XP

Package Contents

Netgear CG814W Wireless Cable Modem Gateway

 {1} Cable Modem

 {1} AC Power adapter

 {1} CAT.5 Ethernet cable {RJ-45}

 {1} USB cable

 {1} User’s Manual

Netgear CG814W Wireless Cable Modem Gateway

Chapter 2: Using the Netgear CG814W

All interface and status LEDs are provided on the front panel. The power

connectors, signal connectors, and Restore Factory Defaults/Reboot button

are on the rear panel.

The Netgear CG814W’s Rear Panel

The rear panel of the Netgear CG814W is where all of the device’s

connections are made.

Power-in The Power Port is where you will connect the included

AC Power adapter.

USB The USB Port. You can connect the Gateway to PC

using USB line.

1~4 These four LAN (Local Area Network) ports are where

you will connect networked devices, such as PCs, print

servers and any other Ethernet devices you want to put

on your network. If Port 4 is being used, the Uplink Port

will not work.

Cable The Cable Line Port (Coaxial Copper).

Wireless The Wireless Network PC Card is inserted into this slot

to enable the wireless features. This slot is not hot

swappable.

The Restore factory settings Button

Briefly pressing the Reset Button will clear all of the Gateway’s data and

restore the factory defaults. This should be done only if you are experiencing

Netgear CG814W Wireless Cable Modem Gateway

heavy routing problems, and only after you have exhausted all of the other

troubleshooting options. By resetting the Gateway, you run the risk of creating

conflicts between your PCs’ actual IP Addresses and what the Gateway thinks

their IP Addresses should be. You may be forced to reboot the entire

system(s).

If your Gateway locks up, simply power it down for 5 seconds by removing the

power cable from the Gateway’s Power Port. Leaving the power off for too

long could result in the loss of network connections.

The Netgear CG814W’s Front Panel

Green. The power LED illuminates when the device is powered

on.

Red. The Diag LED illuminates when the device goes through its

self-diagnosis mode during boot-up and restart. It will turn off

upon successful completion of the diagnosis.

Green. Blinking when the USB port is activity

Green. The WLAN LED illuminates when the Wireless PC card

slide-in and activity.

1~4 Green. When a successful 100Mbps connection is made through

the corresponding port.

Yellow. When a successful 10Mbps connection is made through

the corresponding port.

Green. Steady on when cable is registered and ready to transfer

data.

Green. Blinking when user data going through the cable modem

to PC present.

Netgear CG814W Wireless Cable Modem Gateway

Chapter 3: Connect the Gateway

Overview

Unlike a simple hub or switch, the Gateway’s setup consists of more than

simply plugging hardware together. You will have to configure your networked

PCs to accept the IP addresses that the Gateway assigns them (if applicable),

and you will also have to configure the Gateway with setting(s) provided by

your Internet Service Provider (ISP).

The installation technician from your ISP should have left the setup

information with you after installing your broadband connection. If not, you can

call your ISP to request the data.

Once you have the setup information you need for your specific type of

Internet connection, you can begin installation and setup of the Gateway.

Connecting Your Hardware Together and Booting Up

1. Before you begin, make sure that all of you hardware is powered off,

including the Gateway, PCs, hubs, and switches.

2. Connect one end of an Ethernet cable to one of the LAN ports (labeled 1, 2,

3, or 4) on the back of the Gateway and the other end to a standard port on

a network device, e.g., a PC, print server, hub, or switch. Repeat the above

step to connect more PCs or network devices to the Gateway.

3. Connect the cable from your ISP to the Cable port on the Gateway’s back

panel.

4. Connect the power-supply cable to the Power port on the rear of the

Gateway, then plug the supplied AC power cable into a power outlet and

power on the Netgear CG814W.

• The Power LED on the front panel will light up green as soon as the

power adapter is connected properly.

• The Diag LED will light up red for a few seconds when the Gateway

Netgear CG814W Wireless Cable Modem Gateway

goes through its self-diagnostic test. The LED will turn off when the

self-test is complete.

5. Power on the network devices that connected to the Netgear CG814W.

The Hardware Installation is complete. Continue to the next page to

configure your PCs with Netgear CG814W.

Andere Handbücher für CG814W

Inhaltsverzeichnis

Andere NETGEAR Tor Handbücher

NETGEAR

NETGEAR SSL312 - ProSafe SSL VPN Concentrator 25 Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

NETGEAR

NETGEAR CG3100Dv3 Bedienungsanleitung

NETGEAR

NETGEAR VEVG2660-1TKSAS Bedienungsanleitung

NETGEAR

NETGEAR Lifestyle ASG1100 Bedienungsanleitung

NETGEAR

NETGEAR CVG824G Bedienungsanleitung

NETGEAR

NETGEAR CG814WG Bedienungsanleitung

NETGEAR

NETGEAR CG3300CMR Bedienungsanleitung

NETGEAR

NETGEAR DG824M - 802.11b Wireless ADSL Modem Bedienungsanleitung

NETGEAR

NETGEAR CG3000Dv2 Bedienungsanleitung

NETGEAR

NETGEAR ADT Pulse Gateway PGZNG1 Bedienungsanleitung

NETGEAR

NETGEAR CG3700EMR-1CMNDS Bedienungsanleitung

NETGEAR

NETGEAR CG3300D Bedienungsanleitung

NETGEAR

NETGEAR CG814WG Bedienungsanleitung

NETGEAR

NETGEAR supernet Bedienungsanleitung

NETGEAR

NETGEAR CG3000D-1CXNAS Bedienungsanleitung

NETGEAR

NETGEAR DSL VVG2000 Bedienungsanleitung

NETGEAR

NETGEAR C3700 Bedienungsanleitung

NETGEAR

NETGEAR C3000 Bedienungsanleitung

NETGEAR

NETGEAR CG4500BDv2 Bedienungsanleitung

NETGEAR

NETGEAR Sprint 6100D Technisches Datenblatt

NETGEAR

NETGEAR CG814WH Bedienungsanleitung

NETGEAR

NETGEAR CGD24N Bedienungsanleitung

NETGEAR

NETGEAR CVG834G Bedienungsanleitung

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung

RTA

RTA 460MCBC-N2E Technisches Datenblatt