NETGEAR DG814 - DSL Modem Internet Gateway Bedienungsanleitung

with 4-port 10/100 Mbps switch DG814

DSL Modem Internet Gateway

Installation Guide

Technical Support

YOU MUST REGISTER TO OBTAIN TECHNICAL SUPPORT. PLEASE RETAIN

PROOF OF PURCHASE AND THE WARRANTY INFORMATION.

To register your product, get product support or obtain product information and product

documentation, go to http://www.NETGEAR.com/register.

You’ll find technical support information at http://www.NETGEAR.com/ through the

Customer Service area. If you want to contact technical support by telephone, see the support

information card for the correct telephone number for your country.

Technical support is available 24 hours a day, 7 days a week.

NETGEAR, INC.

E-mail: [email protected]

www.NETGEAR.com

NETGEAR and Auto Uplink are trademarks or registered trademarks of NETGEAR, Inc. in the United States and/or

other countries.

Other brand and product names are trademarks or registered trademarks of their respective holders.

Information is subject to change without notice.

Introduction

Thank you for purchasing a NETGEAR DG814 DSL Modem Internet Gateway. With this

gateway you can have secure Internet access through its high-speed ADSL modem and share

this modem with several computers.

This installation guide shows you how to connect the gateway and configure it and your

computers for secure Internet access. Setup is easy—follow the instructions in this guide and

your system will be up and running quickly.

With Auto Uplink™on each network port, you don’t have to worry about which type of Ethernet

cable you use when you connect your computers, servers or other network devices to the gateway.

Each network port automatically configures itself correctly when you plug in the cable.

If you have problems, there is a troubleshooting section on pages 11 and 12 to help you. You

can get more detailed troubleshooting information from the Reference Manual on the CD,

online at www.NETGEAR.com, or by phone. There’s a short glossary available on page 13 if

you have questions about terminology and a more extensive glossary in the Reference Manual.

Installation Overview

Estimated time: 15 to 30 minutes

1. Gather the configuration information you have for your Internet account from your

Internet Service Provider (ISP).

2. Connect the gateway to one computer.

3. Configure that computer to work with the gateway and restart the computer and gateway.

4. Configure the gateway and go online to test the connection.

5. Connect other computers, configure them and restart each. (optional)

6. Configure for content filtering or port forwarding. (optional)

On the DG814 Resource CD, you’ll find the DG814 Installation Assistant, which supplements

the instructions in this installation guide by animating the step-by-step procedures given here.

For more detailed information about installation, troubleshooting and configuration

procedures, see the Reference Manual on the CD. 1

DSL Modem Internet Gateway DG814

What’s in the Box

When you open the box, verify that you received everything.

The package includes:

•DG814 DSL Modem Internet Gateway

•AC power adapter

•Microfilter splitter (depending on the country of purchase)

•Category 5 Ethernet straight-through cable

•Phone cable

•DG814 Resource CD, including a full Reference Manual and Installation Assistant

•DG814 Installation Guide (this document)

•Warranty and registration card

•Support information card

DSL Modem Internet

Gateway DG814

DG814 DSL Modem Internet

Gateway Resource CD, installation

guide,support information card &

warranty/registration card

Power adapter

Category 5

100 Mbps

Ethernet cable

Phone Cable

Micro Filter

DSL FILTER

DSL

HPN PHONE

LINE

Gather Configuration Information from

Your Internet Service Provider

Before installing the DG814 gateway, you should have active DSL service and an Internet account

with an Internet Service Provider (ISP).

For each computer that you want to connect to the gateway, you must have

•An available RJ-45 Ethernet port (or adapter) —either built-in or from a network

interface card (NIC) installed in the computer.

Note: If you have a built-in modem or a modem card, the telephone jack for the

modem looks very similar to an RJ-45 Ethernet port, but the RJ-45 port is larger.

•TCP/IP networking installed.

•Windows®computers: Client for Microsoft®Networks software installed.

Note: TCP/IP and Client for Microsoft Networks is installed on most Windows

computers. If you have viewed Web sites with a browser, you are ready to go.

Please see the Reference Manual on the CD if you need help installing either on a

Windows computer.

•A Category 5 (Cat 5) Ethernet patch cable.

Note: There is one cable in the box with the gateway.

Connection information

Later in the setup process you’ll configure the gateway to work with your network and, at that

time, you’ll need to know the type of account you have with your ISP and specific account

information.

The next page includes blanks for you to fill in and refer to later.

Note: Your ISP should have provided you with a summary sheet of all the

information needed to connect your computer to the Internet. If you cannot locate

the information, you’ll have to contact your ISP.

Host and Domain Names

Some ISPs use a specific host or domain name—like CCA7324-A or home. If you haven’t

been given specific information about host or domain names then use the following examples

as a guide:

•If your main e-mail account with your ISP is aaa@yyy.com, then use aaa as your host

name. (Your ISP might call this your account, user, host, computer or system name.)

•If your ISP’s mail server is mail.xxx.yyy.com, then use xxx.yyy.com as the domain name.

Account name:

Domain name:

If your ISP requires a login name and password (possibly because you have a PPPoE or PPPoA

account), fill in the following:

Password:

Service name: (if required by your ISP)

Note: The login name could be called a user name or account name by your ISP.

The login name is case sensitive. You must type it exactly as given by your ISP. For

example, c_jones is a different login name than C_Jones or cjones.

Fixed (or static) IP address

If you have a static IP address through your ISP, fill in the following information:

Internet IP address:

Subnet mask:

Gateway IP address:

DNS server address information

If you were given specific Domain Name System (DNS) server addresses, fill in the following:

DNS Server IP address(es):

...

Note: For example, a

valid IP address could

be 169.254.141.148.

...

Install the Gateway

After unpacking the box and locating the configuration

information, you can install the gateway.

Note: You do not have to power down any

equipment to do this, but if you need to move your

computers (perhaps to get to ports in the back),

you may want to shut down the computers before

moving them.

1. Connect the microfilter splitter into the telephone

wall jack.

2. Connect a phone cord between the DSL port and

one of the smaller connector ports on the gateway.

3. Use an Ethernet cable to connect the computer to one of the four numbered Ethernet

ports on the gateway.

4. To use a telephone with this wall jack, connect a phone cord into the Phone port.

5. Connect the power adapter into the back of the gateway and then plug the adapter into a

power source (such as a wall socket or power strip).

Note: If you want to connect other computers into the gateway, don’t connect them

now. Do that after you know that the gateway setup works with one computer.

4. Turn the gateway’s power on.

Note: If you don’t want to connect a telephone at the wall jack, you may connect the

gateway directly to the wall jack with a phone cord. You can connect a telephone to

the gateway by placing a microfilter between the gateway and the telephone’s cord.

Check the setup

•The Test light turns on for a few seconds and then goes off.

Note: If the Test light stays on or blinks, go to Troubleshooting on page 11.

•The Power and Internet lights should be lit.

•The number of the port with the computer (if powered up)

should be lit and may blink to show network activity.

Note: If the connection is a 100 Mbps connection, the number is green. If it is a

10 Mbps connection, the number is yellow. If either the Power, Internet or port

number light isn’t lit, go to Troubleshooting on page 11. 5

Phone

DSL

Line

DG814 DSL Modem Internet Gateway

Configure the Computer to Work with

the Gateway and Restart the Network

Next, you configure the computer to interact with the gateway. To do this, you configure the

TCP/IP settings on the computer and then restart the network. How you do this depends on

your computer.

Windows Operating System

Normally, you leave the TCP/IP setup parameters at their factory default settings unless you

have a specific reason to change them. You should verify that the computer is set to ‘obtain an

IP address automatically’in the Network control panel.

Windows 98 or Me

1. Choose Settings>Control Panel

from the Start menu.

2. Double-click the Network icon.

3. Click the Configuration tab.

4. In the list of installed network

components, select the TCP/IP

entry for the computer’s

Ethernet adapter or NIC.

5. Click Properties.

6. Click the IP Address tab.

7. If not selected, select Obtain an

IP address automatically.

8. Click the Gateway tab.

9. Select and remove any IP Gateway

addresses that are listed.

10. Click OK and click OK again to.

close the Network control panel.

11. Go to Restarting the Network on the

next page.

Windows 98/Me

Windows 2000 or XP

1. Right-click My Network Place and

choose Properties.

2. Double-click Local Area Network

Connection and click Properties.

3. Select Internet Protocol (TCP/IP) and

click Properties.

4. Select Obtain IP address automatically

and Obtain DNS server address

automatically.

5. Click OK twice and click Close.

6. Go to Restarting the Network.

Macintosh Operating System

Mac OS® 8.6 or 9.x

1. Choose Control Panels >TCP/IP

from the Apple () menu.

2. If not already selected, select Ethernet

in the Connect via list.

3. Select Using DHCP Server in the

Configure list.

4. Click the close box.

5. Click Save.

6. Go to Restarting the Network.

Mac OS X

1. Choose System Preferences from the Apple menu.

2. Double-click Network.

3. If not already selected, select Built-in Ethernet in the Configure list.

4. If not already selected, select Using DHCP in the TCP/IP tab.

5. Click Save.

6. Go to Restarting the Network.

Linux®or UNIX®Operating System

If you’re installing the gateway with a Linux-based or UNIX-based computer, see your system

documentation to set up TCP/IP networking to obtain IP addresses automatically using DHCP.

Restarting the Network

Once you’ve set up your computer to work with the gateway, you must reset the network for

the devices to be able to communicate.

1. Turn the the gateway off, wait 15 seconds, and then power it up again.

2. Wait until the Test light stops blinking. (10 seconds)

3. Restart the computer that is connected to the gateway.

Note: If the Test light stays lit, go to Troubleshooting on page 11.

Mac OS 8.6/9.x

Configure the Gateway and Test the

Connection

Now you configure the gateway to work with your ISP. You’ll need the information you filled

in on page 4. You configure your gateway using Internet browser software such as Microsoft®

Internet Explorer 5.0 or Netscape Navigator®4.7 or later. You can either use the Smart Wizard

or configure the gateway yourself.

1. Start a browser on the computer connected to the gateway.

2. In the Address or Location box, type http://192.168.0.1 and press Enter or Return.

Note: You may want to bookmark this address in your browser for handy access in

the future.

3. In the User Name box, type admin

4. In the Password box, type password

5. Click OK.

The gateway’s Setup Wizard page appears.

6. To have the Setup Wizard automatically configure the router, click Yes, click Next and

follow the instructions on screen.

To configure it yourself, click No, then click Next and continue with the steps listed here.

7. Fill in the form on the Basic Settings page. (Refer to page 4 where you filled in the

information previously.)

Note: Helpful information appears on the right side of the page to assist you as you

fill in the form. You may also find pertinent information in the NETGEAR Router ISP

Guide.

8. Click Apply to have your information sent to the router.

Test the Connection

1. Click the Test button on the Basic Settings page.

This should open a new browser window and take you to NETGEAR’s Web site

(www.NETGEAR.com).

Note: If NETGEAR’S Web site doesn’t appear, go to Troubleshooting on page 11.

2. Close the browser window showing NETGEAR’s success page.

3. Click the Logout button on the left navigation area.

Note: If you get asked about closing the browser window, click Yes.

Andere Handbücher für DG814 - DSL Modem Internet Gateway

Inhaltsverzeichnis

Andere NETGEAR Tor Handbücher

NETGEAR

NETGEAR CG3300D Bedienungsanleitung

NETGEAR

NETGEAR CG814M Bedienungsanleitung

NETGEAR

NETGEAR Sprint 6100D Bedienungsanleitung

NETGEAR

NETGEAR CG3000D-1CXNAS Bedienungsanleitung

NETGEAR

NETGEAR CG814WG V2 Bedienungsanleitung

NETGEAR

NETGEAR D2200D-1FRNAS Bedienungsanleitung

NETGEAR

NETGEAR DEVG2020 DOT Bedienungsanleitung

NETGEAR

NETGEAR CG3100Dv3 Bedienungsanleitung

NETGEAR

NETGEAR DG824M - 802.11b Wireless ADSL Modem Bedienungsanleitung

NETGEAR

NETGEAR CG3000DCR Bedienungsanleitung

NETGEAR

NETGEAR CGD24G Bedienungsanleitung

NETGEAR

NETGEAR CBVG834G Bedienungsanleitung

NETGEAR

NETGEAR DVG631G Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

NETGEAR

NETGEAR CG3000D Bedienungsanleitung

NETGEAR

NETGEAR CG814W Bedienungsanleitung

NETGEAR

NETGEAR CVG824G Bedienungsanleitung

NETGEAR

NETGEAR VEVG2660-1TKSAS Bedienungsanleitung

NETGEAR

NETGEAR CVG824G Bedienungsanleitung

NETGEAR

NETGEAR DVG834G Bedienungsanleitung

NETGEAR

NETGEAR CG814WH Bedienungsanleitung

NETGEAR

NETGEAR Sprint 6100D Bedienungsanleitung

NETGEAR

NETGEAR Sprint 6100D Technisches Datenblatt

NETGEAR

NETGEAR C3000 Bedienungsanleitung

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung

RTA

RTA 460MCBC-N2E Technisches Datenblatt