NETGEAR CVG824G Bedienungsanleitung

1-1

v1.0, November 2006

Chapter 1

Installing the Gateway

This chapter describes how to set up the wireless voice gateway on your Local Area Network

(LAN), connect to the Internet, and perform basic configuration. For information about product

features and compatible NETGEAR products, please see the NETGEAR Web site at

http://www.netgear.com.

Package Contents

The product package should contain the following items:

• NETGEAR® Wireless Cable Voice Gateway

•Wireless Cable Voice Gateway Model CVG824G Quick Install Guide

• AC power adapter with separate battery

• Category 5 (CAT5) Ethernet cable

• USB cable

• NETGEAR CD, including:

– This manual

– Application Notes, Tools, and other helpful information

If any of the parts are incorrect, missing, or damaged, contact your NETGEAR dealer. Keep the

carton, including the original packing materials, in case you need to return the product for repair.

Wireless Cable Voice Gateway Model CVG824G Reference Manual

1-2 Installing the Gateway

v1.0, November 2006

The Gateway Front Panel

The front panel of the CVG824G (Figure 1-1) contains status LEDs.

You can use some of the LEDs to verify connections. Table 1-1 lists and describes each LED on

the front panel of the Voice Gateway. These LEDs are green when lit.

Figure 1-1

Table 1-1. LED Descriptions

Label Activity Description

Power Green Solid Power is supplied to the gateway.

Green Blink Battery is charged.

Amber Solid Discharge battery (when 110V power is shut down).

Amber Blink Battery capacity is low (<10%)

Off Power is not supplied to the gateway.

Cable Link Amber Slow

Blink Scanning downstream channel.

Amber Fast

Blink Synchronization

Green Solid Cable link.

Green Blink Upstream data traffic

Off No configuration.

Wireless Cable Voice Gateway Model CVG824G Reference Manual

Installing the Gateway 1-3

v1.0, November 2006

The Gateway Rear Panel

The label on the bottom of the gateway identifies the connections on the rear panel. The rear panel

includes the following connections, viewed from left to right, as illustrated in Figure 1-2.

•Wireless Antenna: The gateway ships with the wireless antenna already attached.

•Power: AC power adapter input.

•Reset button: Resets the gateway to its factory defaults.

•Four Ethernet LAN ports: Use these ports to connect local computers.

•USB port: If the USB driver is installed, you can connect a local computer to this port.

•Coaxial cable connector: Attach coaxial cable to the cable service provider’s connection.

•Two Voice/Phone ports: With VoIP service, connect one or two handsets to these ports.

Wireless Green Solid The wireless connection is operating normally.

Green Blink Data is being transmitted or received on the wireless interface.

Off No wireless link is detected.

USB Port Green Solid A USB device is connected to the USB port.

Off No USB device is connected.

Voice Ports

(1 and 2) Green Solid Registered with the Call Agent.

Green Blink There is an active call.

Green Slow

Blink Phone is “on-hook”; registration with Call Agent is in progress.

Off No phones are connected to the voice port.

LAN (Local

Area Network) Green On The Local port has detected link with a 100 Mbps device.

Green Blink Data is being transmitted or received at 100 Mbps.

Amber On The Local port has detected link with a 10 Mbps device.

Amber Blink Data is being transmitted or received at 10 Mbps.

Off No link is detected on this port.

Table 1-1. LED Descriptions (continued)

Label Activity Description

Wireless Cable Voice Gateway Model CVG824G Reference Manual

1-4 Installing the Gateway

v1.0, November 2006

Installing the Voice Gateway

Installation is a four-part process. Complete the installation in this order:

1. Check the Installation Requirements. See “Installation Requirements” on page 1-4.

2. Connect the Gateway. See “Connecting the Wireless Voice Gateway” on page 1-5.

3. Log in to the Gateway. See “Logging In To the Wireless Voice Gateway” on page 1-7.

4. Connect to the Internet. See “Connecting to the Internet and VoIP” on page 1-8.

After installation, set up the wireless connection as explained in Chapter 2, “Wireless

Configuration”.

Installation Requirements

Check the requirements listed below before installing the gateway:

•Local Computer. During installation, you need a local computer to connect to the gateway via

Ethernet or USB.

– This computer should be set up to access the cable modem Internet service.

Figure 1-2

Reset button

Wireless antenna

AC power adapter input

Four Ethernet LAN ports to connect local

computers

Coaxial cable to your cable

USB port

service provider Voice/phone ports to

connect handsets

Wireless Cable Voice Gateway Model CVG824G Reference Manual

Installing the Gateway 1-5

v1.0, November 2006

– This computer must be set up to use DHCP to get its TCP/IP configuration from the

gateway. See the link “Preparing a Computer for Network Access:” in Appendix B for

help with DHCP configuration.

•Cabling. Use a Category 5 (CAT5) cable such as the one provided with your gateway for your

LAN connections.

•Cable Modem Service. There must be active Data Over Cable Internet service provided by

cable modem account.

•Internet Service Provider (ISP) Configuration. Depending on how the ISP set up the

Internet account, you will need one or more of these configuration settings to connect the

gateway to the Internet:

– Host and Domain Names

– ISP Domain Name Server (DNS) Addresses

– Fixed or Static IP Address

•Computers on the Network. Each computer that will connect to the gateway must have either

an installed Ethernet Network Interface Card (NIC), USB Host port, or 802.11b or 802.11g

wireless adapter.

Connecting the Wireless Voice Gateway

To install the gateway, connect it to a computer either via an Ethernet or a USB according to the

guidelines in the following sections.

Ethernet Connection

If you are connection a computer to the gateway with an Ethernet cable, following these

instructions.

1. Turn off your computer.

2. Use the coaxial cable provided by your cable company to connect the wireless voice gateway

cable port to your cable line splitter or outlet.

3. Connect the LAN port on the gateway to your computer with the Ethernet cable included in

the box.

4. Plug in the gateway and wait about 30 seconds for the lights to stop blinking.

5. Turn on your computer. If software usually logs you in to your Internet connection, do not run

that software or cancel it if it starts automatically.

Wireless Cable Voice Gateway Model CVG824G Reference Manual

1-6 Installing the Gateway

v1.0, November 2006

6. Verify the following:

a. The power light is lit after turning on the gateway.

b. The cable link light is solid green, indicating a link has been established to the cable

network.

c. The LAN LED is lit for the port where you connected the computer.

USB Connection

To connect a computer to the USB port on the gateway.

1. You must install the USB driver. Insert your NETGEAR CD into the CD drive of your

computer.

a. Connect the USB cable to your modem and plug in the AC power for the gateway.

b. Use the USB cable to connect your computer to the gateway.

c. The Found New Hardware Windows installation wizard prompts for the drivers.

d. Browse to the NETGEAR CD and install the USB driver by clicking through the

Windows wizard prompts.

Note: The USB connection option is only available for Windows PCs. Also, Windows 95

does not support USB without special operating system upgrades and patches.

Wireless Cable Voice Gateway Model CVG824G Reference Manual

Installing the Gateway 1-7

v1.0, November 2006

2. Connect your computer to the USB port on the gateway.

3. Plug in your gateway and wait about 30 seconds for the lights to stop blinking.

4. Now, turn on your computer. If software usually logs you in to your Internet connection, do

not run that software or cancel it if it starts automatically.

5. Verify the following:

a. The power light is lit after turning on the gateway.

b. The cable link light is solid green, indicating a link has been established to the

cable network.

c. The USB light is lit.

Logging In To the Wireless Voice Gateway

To log in to the gateway:

Figure 1-3

Note: To connect to the gateway, your computer must be configured to use DHCP. For

instructions on how to do this, see the link to “Preparing a Computer for Network

Access:” in Appendix B.

Wireless Cable Voice Gateway Model CVG824G Reference Manual

1-8 Installing the Gateway

v1.0, November 2006

1. Using the computer that you first used to access your cable modem Internet service, connect to

the gateway by typing http://192.168.0.1 in the address field of your Internet browser.

2. When prompted to log in, enter the user name and password.

• The default parent user name and password are superuser and password, both in lower

case letters.

• The default child user name and password are admin and password, both in lower case

letters.

You are now connected to the gateway.

Connecting to the Internet and VoIP

To configure the gateway to connect to the Internet.

1. From under Setup on the main menu, select Basic Settings. The Basic Settings screen shown

below will display.

Figure 1-4

Note: You can use the parent or child user name and password to install the gateway.

If you plan to set up Parental Control or MAC Filtering, then you need to log in

as the parent.

http://192.168.0.1

Wireless Cable Voice Gateway Model CVG824G Reference Manual

Installing the Gateway 1-9

v1.0, November 2006

2. Select Dynamic or Static IP Address:

• If your service provider assigns your IP address through DHCP, select “Dynamic IP.”

• If your service provider assigned you a permanent, fixed (static) IP address for your PC,

select “Static IP.” Then enter the IP address that your ISP assigned. Also enter the Static IP

Mask (also known as netmask), Gateway IP address and Domain Name Server (DNS)

Address.

• The WAN Default Gateway is the ISP’s router to which your gateway will connect.

• A DNS server is a host on the Internet that translates Internet names (such as

http://www.netgear.com) to numeric IP addresses. Typically your ISP transfers the IP

address of one or two DNS servers to your gateway during login. If the ISP does not

transfer an address, you must obtain it from the ISP and enter it manually here. If you enter

an address here, you should reboot your PCs after configuring the gateway.

3. Click Apply to accept these settings.

Figure 1-5

Dynamic IP Static IP

Wireless Cable Voice Gateway Model CVG824G Reference Manual

1-10 Installing the Gateway

v1.0, November 2006

4. If you have VoIP service, connect the phone to a Voice Port 1. If your service includes a

second line, you can connect that phone to Voice Port 2. To check the voice status, see “MTA

Status” on page 4-3.

To set up a wireless connection, see Chapter 2, “Wireless Configuration”.

Andere Handbücher für CVG824G

Inhaltsverzeichnis

Andere NETGEAR Tor Handbücher

NETGEAR

NETGEAR D2200D-1FRNAS Bedienungsanleitung

NETGEAR

NETGEAR DEVG2020 DOT Bedienungsanleitung

NETGEAR

NETGEAR CG814WH Bedienungsanleitung

NETGEAR

NETGEAR CG814WG Bedienungsanleitung

NETGEAR

NETGEAR CG4500BD Bedienungsanleitung

NETGEAR

NETGEAR VEVG2660-1TKSAS Bedienungsanleitung

NETGEAR

NETGEAR CG3000DCR Bedienungsanleitung

NETGEAR

NETGEAR CVG824G Bedienungsanleitung

NETGEAR

NETGEAR CG3300D Bedienungsanleitung

NETGEAR

NETGEAR CG814WG Bedienungsanleitung

NETGEAR

NETGEAR DG824M - 802.11b Wireless ADSL Modem Bedienungsanleitung

NETGEAR

NETGEAR C3000 Bedienungsanleitung

NETGEAR

NETGEAR CG3000D Bedienungsanleitung

NETGEAR

NETGEAR CG814W Bedienungsanleitung

NETGEAR

NETGEAR CG3000D Bedienungsanleitung

NETGEAR

NETGEAR CG3100 Bedienungsanleitung

NETGEAR

NETGEAR FVS318 - ProSafe VPN Firewall Router Bedienungsanleitung

NETGEAR

NETGEAR CG814WG Kurzanleitung

NETGEAR

NETGEAR DG824M - 802.11b Wireless ADSL Modem Bedienungsanleitung

NETGEAR

NETGEAR Sprint 6100D Bedienungsanleitung

NETGEAR

NETGEAR CG814M Bedienungsanleitung

NETGEAR

NETGEAR CG3000D-1CXNAS Bedienungsanleitung

NETGEAR

NETGEAR C3700 Bedienungsanleitung

NETGEAR

NETGEAR DG814 - DSL Modem Internet Gateway Bedienungsanleitung

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung

RTA

RTA 460MCBC-N2E Technisches Datenblatt