NETGEAR CG3000D Bedienungsanleitung

Home Wi-Fi Gateway Instructions

1. Connect the gateway. Use the coaxial cable provided by BendBroadband to connect the cable port

(A) to your cable outlet.

2. Connect your computer to the cable modem gateway with an Ethernet cable (B), or via a wireless

device using the default settings located on the back of your wireless gateway.

3. Attach the power adapter cable to the

gateway and plug it into an electrical

outlet. Make sure that the Power button on

the rear panel is in the ON position.

After the gateway and power is connected,

the gateway will automatically attempt to

do the following:

Connect to the BendBroadband cable network and download the latest configuration files.

This can take up to 15 minutes to complete.

Obtain an IP address for the gateway. Then the gateway assigns an IP address for the

connected PC.

Connect to the Internet.

4. Wait for the LED lights to stop blinking (as noted above this could take up to 15 minutes when the

Gateway is first powered on). Then verify the following:

The Power LED is solid green.

The Downstream and Upstream LEDs are lit.

The Internet LED is solid green, indicating a link has been established to the Internet.

The LAN LED is lit that corresponds to the local Ethernet port where you connected your

computer.

For more information, see the LED table below.

HOME Wi-Fi USER GUIDE

1. Positioning Your Unit

The operating distance or range of your wireless connection can vary significantly depending on the

physical placement of your unit. For example, the thickness and number of walls the wireless signal

must pass through might limit the range.

For best results, place your Gateway:

Near the center of the area where your computers and other devices will operate, preferably

within line of sight to your wireless devices.

Accessible to an AC power outlet and near Ethernet cables for wired computers.

In an elevated location such as a high-shelf, keeping the number of walls and ceilings between

the Gateway and your wireless devices to a minimum.

Away from any large metal surfaces, such as a solid metal door or aluminum studs. Large

expanses of other materials such as glass, insulated walls, fish tanks, mirrors, brick, and

concrete can also affect your wireless signal.

If placing 2 Gateways or other wireless access points, do not place them within 15 feet of one

another, as the antennas are tuned for this optimum distance. Orient the 2 units with the front

panels (the side with the Power light) facing each other.

2. Password, SSID and Passphrase Set-Up

If you are unsure how to change the settings, it is recommended that you not change them as

security is already optimally configured on your new Gateway. In order to change your settings, you

will need to access the Gateway’s web-based user interface.

Accessing the web-based User Interface

Open up a web browser (Internet Explorer, for example) and enter the IP address

http://192.168.0.1 in your browser’s address bar.

Internet Explorer will show a security window as follows:

Enter the following:

Username: admin

Password: password

Press enter or click “OK”

Changing the SSID name

By default, your SSID (name of your wireless connection) is encrypted specifically for your Gateway

for added security. The SSID name should always begin with ‘CG3000D’.

To change your SSID, click on Wireless Settings under Setup. Type the new name of your network in

the ‘Name(SSID)’ field and click Apply.

Changing the password

Default Username: admin

Default Password: password

To change the router password:

1. In the main menu, under Maintenance,

select Set Password.

2. To change the password, enter the new

password twice.

3. Click Apply to save your changes.

Note: You can also restore factory default settings by selecting “Yes” and clicking on apply.

Changing your wireless passphrase

The default wireless Passphrase for the gateway is located on the back of the Gateway for your

convenience.

The default wireless Passphrase is secure and can remain as the default. However, you can change

it by clicking on Wireless Settings under Setup. WPA-PSK[TKIP] + WPA2-PSK[AES] should already be

selected. Enter in a new password in the Passphrase box. Must be 8 –63 characters.

NOTE: It is NOT recommended to “disable” the Gateway security. It will allow others to gain access to your

network and could cause a potential security risk to personal folders, files, documents and allow others to

contribute to your bandwidth usage.

3. Using Push ‘N’ Connect (WPS) Wireless Setup

Push 'N' Connect (WPS) can be a quick way to automatically set up your gateway’s wireless network

and set up your wireless computer to connect to it at the same time. WPS, also called Wi-Fi

Protected Setup, is a relatively new technology, so before you decide to use it, check to make sure

your wireless computers and devices support WPS. Look for the symbol on all computers that

connect wirelessly to the gateway. If you do not see the symbol on all computers that will

connect to the wireless network, then you should connect them using the Wi-Fi Setup (See

Connecting wireless enabled devices via Wi-Fi). Then, you can still use WPS to set up the wireless

connection for the computers that support WPS.

The WPS button on the gateway when pressed will open a 2-minute window for other WPS-

enabled devices to connect to the router. There are two different methods for connecting with

WPS.

Method 1: Pin

The gateway is assigned a PIN which can be found in the Gateway’s user interface. Once logged in,

click on Wireless Settings under Advanced (Under WPS settings, next to “Router’s Pin:”) For

example, the PIN is used for devices that require manual entry of the WPS PIN, or with WPS

registrar discovery services found in Windows Vista.

1. First, make sure you know how WPS works on your computer or wireless device. If it works

with WPS, there will be a WPS utility feature and it might have a WPS button Log into the

gateway.

2. In the main menu, select WPS Settings, and then click Next. The Add WPS Client screen

displays. Any computer or wireless device that will connect via wireless to the gateway is a

client. After it is added as a client, it will be able to automatically connect to the gateway.

3. Select the PIN radio button.

4. Type the PIN that you located in Step 1 in the Enter Client’s PIN field, and then click Next.

The WPS LED on the front of the gateway begins to blink.

The gateway tries to communicate with the wireless computer or device for 4 minutes.

If the Security Option in the Wireless Settings screen was set to Disabled, it is automatically

changed to WPA-PSK (including a PSK security password).

When the computer connects to the wireless network, the gateway sends its SSID and

WPA-PSK or WPA2-PSK configuration to that computer.

5. On the computer that just joined the wireless network, make sure you can connect to the

Internet. You should see the gateway’s Internet LED blink, showing that its Internet connection

is in use.

Method 2: Push Button

This method is used when your wireless device has the ability to connect using WPS with a button.

1. First, make sure you know how WPS works on your computer or wireless device. If it works

with WPS, there will be a WPS utility feature and it might have a WPS button. Push the WPS

button on the front of the Gateway.

The WPS LED on the front of the gateway begins to blink.

The Gateway tries to communicate with the wireless computer or device for 2 minutes.

Any computer or wireless device that will connect via wireless to the gateway is a client. After it

is added as a client, it will be able to automatically connect to the gateway.

2. Go to the wireless computer, and run its WPS configuration utility. Follow the utility’s

instructions to click the WPS button. When the computer connects to the wireless network,

the gateway sends its SSID and WPA-PSK or WPA2-PSK configuration to that computer.

3. On the computer that just joined the wireless network, make sure you can connect to the

Internet. You should see the gateway’s Internet LED blink, showing that its Internet connection

is in use.

4. Connecting wireless enabled devices via Wi-Fi

If you do not have wireless devices that can connect using WPS, you can manually enter in the

security Passphrase or Network Key. To do this, it will depend on your operating system.

In Microsoft Windows XP, to link the Router with your PC via Wi-Fi, go to Start > Connect to >

click on Wireless Network Connection > choose “CG3000DXX” and click Connect.

In Microsoft Windows Vista, to link the Gateway with your PC via Wi-Fi, go to Start > Connect

to > choose “CG3000DXX” and click Connect.

In Microsoft Windows 7, to link the Gateway with your PC via Wi-Fi, click on next to the

clock on the start bar > choose “CG3000DXX” and click Connect.

If using a MAC, click on the wireless icon in the menu bar next to the time clock, then select and

choose “CG3000XX” from the dropdown list.

5. Troubleshooting Quick Tips

This section describes tips for troubleshooting common problems:

Be sure to restart your network in this sequence.

1. Unplug the Gateway’s power.

2. Turn off the computers/devices connected to the Gateway.

3. Plug in the Gateway to power. Wait 2 minutes.

4. Turn on the computer/devices.

Make sure that the Ethernet cables are securely plugged in.

The Internet status lights (1, 2, 3, and 4) on the Gateway are on if the Ethernet cable connecting

the computer and the Gateway is plugged in securely and the computer is turned on.

Ensure that both the computer and the Gateway are plugged into power.

Make sure the wireless settings in the computer and Gateway match

For a computer connected via wireless, the wireless network name (SSID) and WPA security

settings for the Gateway and wireless computer must match exactly.

If you have enabled the Gateway to restrict wireless access by the specific MAC address, you

must remove the wireless computer’s MAC address from the MAC Filtering section.

Make sure the network settings of the computer are correct

Wired and computers connected via wireless must have network (IP) addresses on the same

network as the Gateway. The simplest way to do this is to configure each computer to obtain an IP

address automatically using DHCP. Refer to the DHCP documentation that came with your

computer.

The Power light is not ON or is blinking

If the Power and other lights are off when your unit is turned on:

Make sure that the power cord is properly connected and that the power adapter is properly

connected to a functioning power outlet.

Check that you are using the power adapter that NETGEAR supplied for this product.

Ensure that the power switch located on the back of your Gateway is in the ON position.

The Wireless or Ethernet port lights are not on

If neither the Ethernet port lights nor the wireless light come on when the Ethernet connection is

made, check the following:

Make sure that the Ethernet cable connections (1, 2, 3, and 4) are secure at the computer and

at the Gateway.

Make sure that connected computer’s power is turned ON.

Press the wireless button on the front of the Gateway to turn the Wireless light on.

Restoring the Default Configuration and Password

This section explains how to restore the factory default configuration settings, changing the

router’s administration password back to password. You can erase the current configuration and

restore factory defaults in two ways:

Use the function within the web interface.

Use the restore factory settings button on the rear panel of the unit. Use this method for cases

when the web-based administration utility is inaccessible.

To restore the factory default configuration settings when the web-based administration utility is

inaccessible, you must use the restore settings button on the rear panel of the router.

1. Press and hold the restore settings button for 10 seconds.

2. Release the restore settings button, and wait for the router to reboot.

Andere Handbücher für CG3000D

Inhaltsverzeichnis

Andere NETGEAR Modem Handbücher

NETGEAR

NETGEAR Orbi Pro SRC60 Bedienungsanleitung

NETGEAR

NETGEAR Nighthawk CM1200 Bedienungsanleitung

NETGEAR

NETGEAR CM1000v2 Bedienungsanleitung

NETGEAR

NETGEAR FVL328 - Cable/DSL ProSafe VPN Firewall... Bedienungsanleitung

NETGEAR

NETGEAR DG814 - DSL Modem Internet Gateway Bedienungsanleitung

NETGEAR

NETGEAR DM200 Bedienungsanleitung

NETGEAR

NETGEAR AC329U Bedienungsanleitung

NETGEAR

NETGEAR CMD31T Bedienungsanleitung

NETGEAR

NETGEAR LB1120-100NAS Bedienungsanleitung

NETGEAR

NETGEAR CM600 Bedienungsanleitung

NETGEAR

NETGEAR DM111P - ADSL2+ Ethernet Modem Bedienungsanleitung

NETGEAR

NETGEAR CM1000v2 Bedienungsanleitung

NETGEAR

NETGEAR DG834GV Montageanleitung

NETGEAR

NETGEAR DM200 Bedienungsanleitung

NETGEAR

NETGEAR DG834PN - RangeMax ADSL Modem Wireless... Bedienungsanleitung

NETGEAR

NETGEAR LB2120 Series Bedienungsanleitung

NETGEAR

NETGEAR AirCard 340U Bedienungsanleitung

NETGEAR

NETGEAR CM1000 Bedienungsanleitung

NETGEAR

NETGEAR AC785S Bedienungsanleitung

NETGEAR

NETGEAR CM400 Bedienungsanleitung

NETGEAR

NETGEAR WNDRMAC Bedienungsanleitung

NETGEAR

NETGEAR CGD24G Bedienungsanleitung

NETGEAR

NETGEAR CM500 Bedienungsanleitung

NETGEAR

NETGEAR CM700 Bedienungsanleitung

Beliebte Modem Handbücher anderer Marken

Davicom

Davicom DM562AP Bedienungsanleitung

EpiValley

EpiValley TATA indicom SXC-1080 Bedienungsanleitung

Zte

Zte WiMAX Bedienungsanleitung

Intelimax

Intelimax MA-2060 Bedienungsanleitung

SMC Networks

SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch

Telstra

Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Bedienungsanleitung

Samsung

Samsung AceLink SAM-335A Bedienungsanleitung

Enfora

Enfora Enabler-G Kurzanleitung zur Einrichtung

iRZ

iRZ ATM2-232 Bedienungsanleitung

Zhone

Zhone 6310 Bedienungsanleitung

Paradyne

Paradyne Hotwire 7976 Bedienungsanleitung

US Robotics

US Robotics 3453C Bedienungsanleitung

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung

Zte

Zte MF823 Bedienungsanleitung

Four-Faith

Four-Faith F1403 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AIRLINK MP595W Bedienungsanleitung

Gemtek

Gemtek WiMAX WIXFBR-103 Bedienungsanleitung