NETGEAR ME101 - Wireless EN Bridge Network Converter Bedienungsanleitung

Table of Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

1: Preparing to Install the ME101 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Placement and Range Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Operating Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

ME101 Default Wireless Configuration Settings . . . . . . . . . . . . . . . . . . .3

2: Installing the ME101 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

3: Configuring Your ME101 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Identifying the Wireless Network Name (SSID), IP Address,

and WEP Security Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Installing the Configuration Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Configuring the Bridge for Your Wireless Network . . . . . . . . . . . . . . . . .8

Changing the Password for the Bridge . . . . . . . . . . . . . . . . . . . . . . . . . .9

Upgrading the Bridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Enabling WEP Security on the Bridge . . . . . . . . . . . . . . . . . . . . . . . . . .10

Using the Browser-based Configuration Software . . . . . . . . . . . . . . . . . .11

ME101 02.11b Wireless Ethernet Bridge Lights and Settings . . . . . . . . . . . .14

ME101 802.11b Wireless Ethernet Bridge Lights . . . . . . . . . . . . . . . . . .14

Restoring the Bridge to the Default Settings . . . . . . . . . . . . . . . . . . . . . .14

ME101 802.11b Wireless Ethernet Bridge Status Settings . . . . . . . . . . . .15

Troubleshooting Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

ME101 02.11b Wireless Ethernet Bridge Specifications . . . . . . . . . . . . . . . .1

System Requirements for the Bridge . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

ME101 802.11b Wireless Ethernet Bridge Specifications . . . . . . . . . . . . .18

Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Introduction

Thank you for purchasing a NETGEAR ME101 802.11b Wireless Ethernet Bridge. With this

bridge you can connect a gaming console, personal computer, printer, or other Ethernet-

enabled device to communicate with your wireless router or access point.

This guide shows you how to connect the bridge and configure it with your wireless router or

access point. Setup is easy – follow the instructions in this guide and your network will be up

and running quickly.

Package Contents

The product package should contain the following items:

•ME101 802.11b Wireless Ethernet Bridge

•Power adapter

•Ethernet crossover cable

•GearBox™CD for Wireless Ethernet Bridge, including:

- Configuration Utility software

- User Manual for the Model ME101 802.11b Wireless Ethernet Bridge in

Adobe®Acrobat®PDF file format

•Installation Guide

•Warranty card

•Support information card

GearBox™CD for Wireless

Ethernet Bridge, Installation guide,

Support information card,

Warranty card

100 Mbps

Ethernet cable

ME101 Wireless Ethernet Bridge

Power adapter

System Requirements

Before installing the ME101 802.11b Wireless Ethernet Bridge, please make sure that these

minimum requirements have been met:

•You must have a wireless network set up with either a wireless router or access point.

If the default settings on the bridge do not work, you will need to configure the bridge. To

configure the bridge with the configuration utility, you must have a personal computer with:

•Windows®98 or 98SE, Me, 2000, or XP.

•A CD-ROM drive.

•2 Megabytes of free hard disk space.

If you don’t have a Windows-based computer or a CD-ROM drive, you may use a browser to

configure the bridge.

Preparing to Install the ME101

Placement and Range Guidelines

Computers and other Ethernet-enabled devices can connect over 802.11b wireless networks

indoors at a maximum range of approximately 500 feet. However, the operating distance or

range of your wireless connection can vary significantly based on the physical location of the

ME101 802.11b Wireless Ethernet Bridge. For best results, avoid potential sources of

interference, such as:

•Large metal surfaces

•Microwaves

•2.4 GHz cordless phones

In general, 802.11b wireless devices can communicate through walls. However, if the walls are

constructed with concrete or have metal (or metal mesh), the effective range will decrease if

such materials are between the wireless devices.

Operating Mode

The ME101 Wireless Ethernet Bridge operates only in infrastructure mode. In this mode

devices and computers communicate with each other by first going through a wireless router or

access point. For example, infrastructure mode is used when you have computers in a house

connected to an access point that is attached to a router. The router lets multiple computers

share a single cable or DSL broadband Internet connection.

ME101 Default Wireless Configuration Settings

Note: If you are setting up a new wireless network, please set up the network and make sure it

works before adding the ME101 Wireless Ethernet Bridge into the network.

You will need to identify the wireless configuration and security parameters already defined in

your wireless network.

Note: All NETGEAR, Inc. 802.11b wireless access products use the same factory settings as the

ME101 and will work without any configuration changes.

The factory default settings for your ME101 802.11b Wireless Ethernet Bridge are:

•Mode (Infrastructure or Ad-Hoc): Infrastructure

•Wireless network name Service Set Identification (SSID): Any

Note: Any means the bridge will connect to the first access point or wireless router that

responds to the bridge’s request for connection. This may not be the strongest signal or the

closest access point or router. For the ME101 Wireless Ethernet Bridge to communicate

with a specific wireless router or access point, both devices must be configured with the

same SSID.

•User ID: admin

•Password: password

•Authentication type: Auto

•WEP security: Disabled

•Country/Region: U.S.A.

Warning: Having the bridge set to the wrong country or region may result in the violation

of local laws.

•IP address: 192.16 .0.200

Installing the ME101

This section provides instructions for connecting the ME101 802.11b Wireless Ethernet Bridge

to any Ethernet-enabled device using the default settings.

Note: If you find that the default settings don’t work, if you know that you’ve configured your

wireless network with WEP security, or if you are not in the United States, you’ll have to

configure the bridge before connecting it to the Ethernet-enabled device. To configure the

bridge, see Configuring Your ME101 on page 6.

1. Unpack the box and verify the contents.

2. Identify a flat surface where you will put the wireless bridge. For best results, follow

these guidelines:

•Place it away from potential sources of interference, such as computers, monitors,

TVs, microwaves, cordless phones, or large metal surfaces.

Warning: Failure to follow these guidelines can cause intermittent or complete failure

of wireless connectivity.

•Place it in an elevated location such as a high shelf or on a wall in the center of

your wireless access area.

3. Lift the bridge’s antenna so it is vertical.

MR814

Cable/DSL

Wireless Router

Cable/DSL

modem

Gaming console with

ME101 802.11b Wireless

Ethernet Bridge

family

room

family

room

Macintosh computer with

ME101 802.11b Wireless

Ethernet Bridge

Internet

NETGEAR

Desktop PC with

Ethernet connection

4. Turn off the gaming console or other Ethernet-enabled device.

5 Connect the provided Ethernet cable between the ME101 Wireless Bridge and the gaming

console or other Ethernet-enabled device.

Note: The ME101 Wireless Bridge should be connected to one device only. Don’t connect

it through a network switch or hub.

6. Connect the power adapter to the wireless bridge and plug the power adapter in to a

power outlet. The Power and Wireless LAN lights should light up.

7. After you see the Wireless LAN light light up, turn on the gaming console or other

Ethernet-enabled device.

If the bridge and the Ethernet-enabled device are successfully connected, the Network

light will light up. This light flashes when there is network activity.

Note: If your setup works with the default settings, you don’t need to install the software

from the provided CD to configure the bridge unless you need to change the

Country/Region setting from the default setting (U.S.A.).

Default Ethernet AntennaDC in 5V

Gaming console or other

Ethernet-enabled device

ME101 Wireless

Ethernet Bridge

Configuring Your ME101

If the default settings don’t work in your wireless network, you need to configure the bridge.

Identifying the Wireless Network Name (SSID), IP Address,

and WEP Security Settings

You may want to print this page separately, fill in the configuration parameters, and put it in a

safe place for possible future reference. For an existing wireless network, the person who set up

the network will be able to provide this information.

Note: For the access point or router and the bridge to communicate with each other, both must

be configured with the same SSID, WEP security settings, and the same IP subset address.

•Wireless Network Name (SSID): The Service Set Identification (SSID) identifies the

wireless local area network. Any is the default ME101 SSID. If you have named your

wireless network with a different SSID, write your network’s SSID on the line below.

Wireless network name (SSID): ______________________________

•Bridge IP Address: Your Ethernet network has an IP subset address given as a set of three

numbers (xxx.xxx.xxx.yyy) plus a last set of numbers to identify each device on the

network. The default IP address for the bridge is 192.168.0.200. To communicate to your

Ethernet network, the bridge must have an address consistent with your network’s IP

address. If you need to change the bridge’s IP address, write down the new address.

Bridge’s IP address: ______________________________

•WEP Security Encryption key: The default WEP encryption mode of the bridge is

disabled. If you have set up WEP security on your wireless network (through the router or

access point), you’ll need to configure the bridge using the same WEP security parameters.

WEP Encryption Key Size, circle one: 40/64 or 128 bits

WEP Encryption Passphrase, if used in the router or access point: ___________________

A passphrase is used to automatically generate the WEP hexadecimal numbers for the key.

Otherwise, you will have to manually enter up to four hexadecimal numbers.

WEP Hexadecimal Numbers: ______________________________

______________________________

Installing the Configuration Utility

To configure the bridge you use the configuration utility on the included GearBox CD.

Note: To run the configuration utility, you must have the bridge directly connected using the

provided Ethernet crossover cable to a computer running Windows 98 or 98SE, Me, 2000, or

XP. If you have a Macintosh®computer, use the browser-based configuration procedure on

page 11.

1. Insert the GearBox CD in a networked computer’s CD-ROM drive.

The NETGEAR software installation utility should start up automatically.

2. Click Install Utility.

3. Follow the instructions on screen to install the ME101 Configuration Utility.

4. Click Finish.

5. Restart the computer.

6. If you had the bridge connected to another device, you must connect it to the computer

where you installed the Configuration Utility.

a. If you had the bridge powered up, unplug it.

b. Connect the provided Ethernet crossover cable

between the computer and the bridge.

c. Plug the power adapter into the bridge and

then plug the power adapter into a power

source.

Default Ethernet AntennaDC in 5V

ME101 Wireless

Ethernet Bridge

Configuring the Bridge for Your Wireless Network

Once you are logged into the Configuration Utility, you can view the status of your home

wireless network and current configuration of the bridge, change the password, enable WEP

security (if you have it set up on your wireless network), select a specific network for the

wireless connection or make other configuration changes.

1. Choose Programs>NETGEAR ME101 Bridge>ME101 Configuration Utility from the

Start menu.

2. If the bridge’s name doesn’t appear in the Bridge Name list, select Browse to have the

utility search for an active bridge.

3. Type password as the password.

4. Click Login.

5. Click the Configuration tab.

6. Either select an SSID name assigned to the wireless

router or access point from the list or type the SSID

name.

Note: If you have NETGEAR wireless devices, the

default SSID is Wireless or NETGEAR.

7. If you are not in the United States, select the correct

country or region from the Country/Region list. Click

Yes to accept the new country or region.

Warning: Having the bridge set to the wrong country

or region may result in the violation of local laws.

8. Type the correct IP address for the bridge. The first

three sets of numbers (xxx.xxx.xxx.yyy) should be the

same as your access point or router. The last set of numbers (.yyy) should be a unique set

of numbers on your network.

9. Click Apply.

10. If you are through making changes, click Exit.

11. To use the bridge with a different computer or other Ethernet-enabled device, return to

Installing the ME101 on page 4 to connect the bridge.

Andere Handbücher für ME101 - Wireless EN Bridge Network Converter

Inhaltsverzeichnis

Andere NETGEAR Netzwerk-Router Handbücher

NETGEAR

NETGEAR ProSafe FVS318N Bedienungsanleitung

NETGEAR

NETGEAR LG2200-1USNAS Bedienungsanleitung

NETGEAR

NETGEAR S8000 Bedienungsanleitung

NETGEAR

NETGEAR DGN2200M - Wireless-N 300 Router Bedienungsanleitung

NETGEAR

NETGEAR Nighthawk AC1900 R7000 Bedienungsanleitung

NETGEAR

NETGEAR AC1450 Bedienungsanleitung

NETGEAR

NETGEAR DGFV338 - ProSafe Wireless ADSL Modem VPN Firewall... Handbuch

NETGEAR

NETGEAR C6300 Bedienungsanleitung

NETGEAR

NETGEAR RT338 Bedienungsanleitung

NETGEAR

NETGEAR GC510P Handbuch

NETGEAR

NETGEAR LBR20 Bedienungsanleitung

NETGEAR

NETGEAR Nighthawk X4S D7800 Bedienungsanleitung

NETGEAR

NETGEAR MR814 - 802.11b Cable/DSL Wireless Router Bedienungsanleitung

NETGEAR

NETGEAR SXK50 Bedienungsanleitung

NETGEAR

NETGEAR WGE101 Bedienungsanleitung

NETGEAR

NETGEAR WGT624 v3 Bedienungsanleitung

NETGEAR

NETGEAR Orbi Pro WiFi 6 AX6000 Bedienungsanleitung

NETGEAR

NETGEAR Orbi LBR1020 Bedienungsanleitung

NETGEAR

NETGEAR DG834Gv3 - 54 Mbps Wireless ADSL Firewall... Bedienungsanleitung

NETGEAR

NETGEAR Home Router Bedienungsanleitung

NETGEAR

NETGEAR ProSafe FR114P Bedienungsanleitung

NETGEAR

NETGEAR Nighthawk M6 Bedienungsanleitung

NETGEAR

NETGEAR R7900 Bedienungsanleitung

NETGEAR

NETGEAR JWNR3000 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung