NETGEAR ME101 - Wireless EN Bridge Network Converter Bedienungsanleitung

Table of Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

1: Preparing to Install the ME101 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Placement and Range Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Operating Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

ME101 Default Wireless Configuration Settings . . . . . . . . . . . . . . . . . . .3

2: Installing the ME101 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Connecting One Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Connecting Multiple Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

3: Configuring Your ME101 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Identifying the Wireless Network Name (SSID), IP Address,

and WEP Security Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Installing the Configuration Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Configuring the Bridge for Your Wireless Network . . . . . . . . . . . . . . . . .9

Changing the Password for the Bridge . . . . . . . . . . . . . . . . . . . . . . . . . .10

Upgrading the Bridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Enabling WEP Security on the Bridge . . . . . . . . . . . . . . . . . . . . . . . . . .11

Using the Browser-based Configuration Software . . . . . . . . . . . . . . . . . .12

ME101 802.11b Wireless Ethernet Bridge Lights and Settings . . . . . . . . . . . .15

ME101 802.11b Wireless Ethernet Bridge Lights . . . . . . . . . . . . . . . . . .15

Restoring the Bridge to the Default Settings . . . . . . . . . . . . . . . . . . . . . .15

ME101 802.11b Wireless Ethernet Bridge Status Settings . . . . . . . . . . . .16

Troubleshooting Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

ME101 802.11b Wireless Ethernet Bridge Specifications . . . . . . . . . . . . . . . .20

System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Bridge Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Introduction

Thank you for purchasing a NETGEAR ME101 802.11b Wireless Ethernet Bridge. With this

bridge you can connect a gaming console, personal computer, printer, or other Ethernet-

enabled device to communicate with your wireless router or access point. If you have a hub,

you can connect more than one Ethernet-enabled device to communicate with your wireless

router or access point through the bridge.

This guide shows you how to connect the bridge and configure it with your wireless router or

access point. Setup is easy – follow the instructions in this guide and your network will be up

and running quickly.

Package Contents

The product package should contain the following items:

•ME101 802.11b Wireless Ethernet Bridge

•Power adapter

•Ethernet crossover cable

•Resource CD for Wireless Ethernet Bridge, including:

- Configuration Utility software

-User’s Guide for the Model ME101 802.11b Wireless Ethernet Bridge in

Adobe®Acrobat®PDF file format

•Installation Guide

•Warranty card

•Support information card 1

Resource CD for Wireless

Ethernet Bridge, Installation Guide,

Support information card,

Warranty card

Cat 5 crossover

Ethernet cable

ME101 Wireless Ethernet Bridge

Power adapter

System Requirements

Before installing the ME101 802.11b Wireless Ethernet Bridge, please make sure that these

minimum requirements have been met:

•You must have a wireless network set up with either a wireless router or access point.

If the default settings on the bridge do not work or if you have multiple ME101 bridges in

your network, you will need to configure the bridge. To configure the bridge with the

configuration utility, you must have a personal computer with:

•Windows®98 or 98SE, Me, 2000, or XP.

•A CD-ROM drive.

•2 Megabytes of free hard disk space.

If you don’t have a Windows-based computer or a CD-ROM drive, you may use Internet

browser software to configure the bridge.

Preparing to Install the ME101

Placement and Range Guidelines

Computers and other Ethernet-enabled devices can connect over 802.11b wireless networks

indoors at a maximum range of approximately 500 feet. However, the operating distance or

range of your wireless connection can vary significantly based on the physical location of the

ME101 802.11b Wireless Ethernet Bridge. For best results, avoid potential sources of

interference, such as:

•Large metal surfaces

•Microwaves

•2.4 GHz cordless phones

In general, 802.11b wireless devices can communicate through walls. However, if the walls are

constructed with concrete or have metal (or metal mesh), the effective range will decrease if

such materials are between the wireless devices.

Operating Mode

The ME101 Wireless Ethernet Bridge operates only in infrastructure mode. In this mode

devices and computers communicate with each other by first going through a wireless router or

access point. For example, infrastructure mode is used when you have computers in a house

connected to an access point that is attached to a router, which lets multiple computers share a

single cable or DSL broadband Internet connection.

ME101 Default Wireless Configuration Settings

Note: If you are setting up a new wireless network, please set up the network and make sure it

works before adding the ME101 Wireless Ethernet Bridge into the network.

You will need to identify the wireless configuration and security parameters already defined in

your wireless network.

Note: All NETGEAR, Inc. 802.11b wireless access products use the same factory settings as the

ME101 and will work without any configuration changes.

The factory default settings for your ME101 802.11b Wireless Ethernet Bridge are:

•Mode (Infrastructure or Ad-Hoc): Infrastructure

•Wireless network name Service Set Identification (SSID): Any

Note: Any means the bridge will connect to the first access point or wireless router that

responds to the bridge’s request for connection. This may not be the strongest signal or the

closest access point or router. For the ME101 Wireless Ethernet Bridge to communicate

with a specific wireless router or access point, both devices must be configured with the

same SSID.

•User ID: admin

•Password: password

•Authentication type: Auto

•WEP security: Disabled

•Country/Region: U.S.A.

Warning: Having the bridge set to the wrong country or region may result in the violation

of local laws.

•IP address: 192.168.0.200

Note: Each device in the network must have a unique IP address. If you have multiple

ME101 bridges in the network, only one can use the default address.

Installing the ME101

This section provides instructions for connecting the ME101 802.11b Wireless Ethernet Bridge

to one or more Ethernet-enabled devices using the default settings.

Note: If you find that the default settings don’t work, if you know that you’ve configured your

wireless network with WEP security, if you are using multiple ME101 bridges, or if you are not

in the United States, you’ll have to configure the bridge before connecting it to the Ethernet-

enabled device. To configure the bridge, see Configuring Your ME101 on page 7.

1. Unpack the box and verify the contents.

2. Identify a flat surface where you will put the wireless bridge. For best results, follow

these guidelines:

•Place it away from potential sources of interference, such as computers, monitors,

TVs, microwaves, cordless phones, or large metal surfaces.

Warning: Failure to follow these guidelines can cause intermittent or complete failure

of wireless connectivity.

•Place it in an elevated location such as a high shelf or on a wall in the center of

your wireless access area.

3. Lift the bridge’s antenna so it is vertical.

MR814

Cable/DSL

Wireless Router

Cable/DSL

modem

Gaming console with

ME101 802.11b Wireless

Ethernet Bridge

family

room

family

room

Macintosh computer with

ME101 802.11b Wireless

Ethernet Bridge

Internet

NETGEAR

Desktop PC with

Ethernet connection

Connecting One Device

Note: If you want to connect multiple devices, see the procedure on page 6.

1. Turn off the gaming console or other Ethernet-enabled device.

2. Connect the provided Ethernet cable between the ME101 Wireless Bridge and the gaming

console or other Ethernet-enabled device.

3. Connect the power adapter to the wireless bridge and plug the power adapter in to a

power outlet. The Power and Wireless LAN lights should light up.

4. After you see the Wireless LAN light light up, turn on the gaming console or other

Ethernet-enabled device.

If the bridge and the Ethernet-enabled device are successfully connected, the Network

light will light up. This light flashes when there is network activity.

Note: If your setup works with the default settings, you don’t need to install the software

from the provided CD to configure the bridge unless you need to change the

Country/Region setting from the default setting (U.S.A.) or you have more than one

ME101 bridge on your network.

Default Ethernet AntennaDC in 5V

Gaming console or other

Ethernet-enabled device

ME101 Wireless

Ethernet Bridge

Connecting Multiple Devices

1. Turn off the gaming console(s) and other Ethernet-enabled device(s).

2. Connect the provided Ethernet cable between the ME101 Wireless Bridge and a hub.

3. Connect the powered down game console(s) and the powered down Ethernet-enabled

device(s) to the hub.

4. Connect the power adapter to the wireless bridge and plug the power adapter in to a

power outlet. The Power and Wireless LAN lights should light up.

5. Connect the power adapter to the hub. Plug the hub’s power adapter in to a power outlet.

6. After the Wireless light on the bridge lights up, turn on any game console(s).

7. Turn on any other Ethernet-enabled devices.

If the bridge and the Ethernet-enabled device(s) are successfully connected, the Network

light on the bridge will light up. This light flashes when there is network activity.

Note: If your setup works with the default settings, you don’t need to install the software

from the provided CD to configure the bridge unless you need to change the

Country/Region setting from the default setting (U.S.A.) or you have more than one

ME101 bridge on your network.

Default Ethernet AntennaDC in 5V

1234

10 BASE-T HUB EN104 Link Rx

Normal / Uplink

PWR

COL

Wireless Router

MR814

Cable or

DSL modem

ME101 Wireless

Ethernet Bridge

EN104TP Ethernet Hub Gaming console or other

Ethernet-enabled device

Configuring Your ME101

If the default settings don’t work in your wireless network, you need to configure the bridge.

Identifying the Wireless Network Name (SSID), IP Address,

and WEP Security Settings

You may want to print this page separately, fill in the configuration parameters, and put it in a

safe place for possible future reference. For an existing wireless network, the person who set up

the network will be able to provide this information.

Note: For the access point or router and the bridge to communicate with each other, both must

be configured with the same SSID, WEP security settings, and the same IP subset address.

•Wireless Network Name (SSID): The Service Set Identification (SSID) identifies the

wireless local area network. Any is the default ME101 SSID. If you have named your

wireless network with a different SSID, write your network’s SSID on the line below.

Wireless network name (SSID): ______________________________

•Bridge IP Address: Your Ethernet network has an IP subset address given as a set of three

numbers (xxx.xxx.xxx.yyy) plus a last set of numbers to identify each device on the

network. The default IP address for the bridge is 192.168.0.200. To communicate to your

Ethernet network, the bridge must have a unique address consistent with your network’s IP

address. If you need to change the bridge’s IP address, write down the new address.

Bridge’s IP address: ______________________________

•WEP Security Encryption key: The default WEP encryption mode of the bridge is

disabled. If you have set up WEP security on your wireless network (through the router or

access point), you’ll need to configure the bridge using the same WEP security parameters.

WEP Encryption Key Size, circle one: 40/64 or 128 bits

WEP Encryption Passphrase, if used in the router or access point: ___________________

A passphrase is used to automatically generate the WEP hexadecimal numbers for the key.

Otherwise, you will have to manually enter up to four hexadecimal numbers.

WEP Hexadecimal Numbers: ______________________________

______________________________

Installing the Configuration Utility

To configure the bridge you use the configuration utility on the included Resource CD.

Note: To run the configuration utility, you must have the bridge connected using the provided

Ethernet crossover cable to a computer running Windows 98 or 98SE, Me, 2000, or XP —

directly or through a hub. If you have a Macintosh®computer, use the browser-based

configuration procedure on page 12.

1. Insert the Resource CD in a networked computer’s CD-ROM drive.

The NETGEAR software installation utility should start up automatically.

2. Click Install Utility.

3. Follow the instructions on screen to install the ME101 Configuration Utility.

4. Click Finish.

5. Restart the computer.

6. If you had the bridge connected to another device, you must connect it to the computer

where you installed the Configuration Utility.

Note: If the bridge and the computer are connected

to the same hub, you don’t need to directly connect

them.

a. If you had the bridge powered up, unplug it.

b. Connect the provided Ethernet crossover cable

between the computer and the bridge.

c. Plug the power adapter into the bridge and

then plug the power adapter into a power

source.

Default Ethernet AntennaDC in 5V

ME101 Wireless

Ethernet Bridge

Andere Handbücher für ME101 - Wireless EN Bridge Network Converter

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere NETGEAR Netzwerk-Router Handbücher

NETGEAR

NETGEAR Orbi Pro SRR60 Bedienungsanleitung

NETGEAR

NETGEAR MR6550 Bedienungsanleitung

NETGEAR

NETGEAR Nighthawk M6 Pro Bedienungsanleitung

NETGEAR

NETGEAR RT338 Bedienungsanleitung

NETGEAR

NETGEAR R6400 Bedienungsanleitung

NETGEAR

NETGEAR RBRE960B Bedienungsanleitung

NETGEAR

NETGEAR GS408EPP Handbuch

NETGEAR

NETGEAR Nighthawk AC2400 Bedienungsanleitung

NETGEAR

NETGEAR C6250 Bedienungsanleitung

NETGEAR

NETGEAR RT328 Bedienungsanleitung

NETGEAR

NETGEAR Orbi Bedienungsanleitung

NETGEAR

NETGEAR R7300DST Bedienungsanleitung

NETGEAR

NETGEAR RM356 - Router - EN Bedienungsanleitung

NETGEAR

NETGEAR JNR3210 Bedienungsanleitung

NETGEAR

NETGEAR WNR2000v2 - Wireless- N 300 Router Bedienungsanleitung

NETGEAR

NETGEAR RT328 Bedienungsanleitung

NETGEAR

NETGEAR WNR2000v2 - Wireless- N 300 Router Bedienungsanleitung

NETGEAR

NETGEAR DG834v4 Bedienungsanleitung

NETGEAR

NETGEAR PR60X Handbuch

NETGEAR

NETGEAR MR814V2 - 802.11b Cable/DSL Wireless Router Bedienungsanleitung

NETGEAR

NETGEAR C6250 Bedienungsanleitung

NETGEAR

NETGEAR PR2000 Bedienungsanleitung

NETGEAR

NETGEAR JNR3210 Leitfaden

NETGEAR

NETGEAR Nighthawk AX6 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung

Dynacord

Dynacord Promatrix 6000 Bedienungsanleitung