NETGEAR ReadyNAS RR4360X Bedienungsanleitung

Installation and

Quick Start

ReadyNAS

RR4360S

RR4360X

Contents

Package Contents ....................................................................................................... 3

Prepare the Installation Site...................................................................................... 3

Install the System in a Rack ...................................................................................... 4

Precautions.............................................................................................................. 4

Rack Installation ..................................................................................................... 5

Install Cable Management................................................................................... 6

Install Disks ................................................................................................................... 7

Basic Setup.................................................................................................................... 9

Reformat Disks...........................................................................................................10

Additional Information .............................................................................................11

Package Contents

Important: Read all safety warnings in the hardware manual for your system before connecting

the system to the power supply.

Your package contains the following items:

• RR4360 chassis including 60 disk trays

• Rack mount rail kit

• Cable management kit

• Ten Power cords. (Five sets of two power cords for the two supplied power supplies. Each

set for a dierent region.)

• Ethernet cable

• 60 screws to optionally screw the disk trays to the disks

Prepare the Installation Site

Keep the following considerations in mind as you install your unit:

• Ambient operating temperature. If the unit is installed in a closed or multi-unit rack

assembly, the ambient operating temperature of the rack environment might be greater

than the ambient temperature of the room. Therefore, consider installing the equipment in

an environment compatible with the maximum rated ambient temperature.

• Reduced airﬂow. Mount the equipment into a rack so that the amount of airﬂow required

for safe operation is not compromised.

• Mechanical loading. Mount the equipment into a rack so that a hazardous condition does

not arise due to uneven mechanical loading.

• Circuit overloading. Consider the equipment’s connection to the power supply circuitry

and the eect of possible overloading of circuits on overcurrent protection and power

supply wiring. Consider equipment nameplate ratings when addressing this concern.

• Reliable ground. This product requires that a reliable ground be maintained at all times.

To ensure this, ground the rack itself. Pay particular attention to power supply connections

other than the direct connections to the branch circuit (for example, the use of power

strips).

• Setup location. This product is intended for installation in a restricted access location

(dedicated equipment rooms, service closets, and the like) only.

• Front clearance. Leave enough clearance in front of the rack (about 64 cm or 25 inches)

to enable you to open the front door completely and in the back of the rack (about 76 cm

or 30 inches) to allow for sucient airﬂow and ease in servicing.

• Rear rack clearance. This product requires nearly the full depth of the rack. Placement of

items such as a power strip inside the rack might block the product from being completely

pushed in.

Install the System in a Rack

Use the rack-mount hardware included with your ReadyNAS or your expansion disk array to

install it in a rack.

Note that the le and right rails are not identical. The le rail is marked with a sticker bearing

the letter L, and the right rail is marked with a sticker bearing the letter R. Each rail has an outer

rail, a middle rail, and an inner rail. Do not exchange the inner rails of the le and right rails.

While installing the system into a rack, keep the ball bearing shuttle locked at the front of the

middle rail.

A minimum of two people are required for safe installation of the system.

DANGER: A unit with installed drives can weigh more than 34 kg (75 pounds). To avoid injury or damage

to the equipment, perform the rack-mount installation with appropriate assistance. We recommend

installing the system into the rack before installing the disks.

Precautions

Follow these rack-mount precautions:

• Ensure that the leveling jacks on the bottom of the rack are fully extended to the ﬂoor with

the full weight of the rack resting on them.

• In single-rack installations, attach stabilizers to the rack. In multiple-rack installations,

couple the racks together.

• Always make sure the rack is stable before extending a component from the rack.

• Extend only one component at a time. Extending two or more simultaneously might cause

the rack to become unstable.

• Review the electrical and general safety precautions that came with the components you

are adding to your chassis.

• Determine the placement of each component in the rack before you install the rails.

• Install the heaviest components on the bottom of the rack ﬁrst, and then work up.

• Use a regulating uninterruptible power supply (UPS) to protect the ReadyNAS from power

surges and voltage spikes and to keep your system operating in case of a power failure.

• Allow any hot-plug drives and power supply modules to cool before touching them.

• Always keep the rack’s front door and all panels and components on the servers closed

when not servicing them to maintain proper cooling.

Rack Installation

Read these instructions in their entirety before you begin.

Note: The rail ends require square holes in the rack. You cannot install the supplied rails using threaded

rail holes.

¾To install the system into a rack:

1. Using the le rail, pull the inner rail out of the outer rail until it is fully extended.

The middle and outer rail might lock in the extended position.

2. Press the locking tab down to release the inner rail and separate it from the outer and

middle rails.

3. Align the hooks on the chassis with the holes in the inner rail and press them together.

4. Slide the rail forward until it locks on to the chassis.

5. Repeat steps 1 through 4 using the right rail.

6. If the middle and outer rails are locked on either of the rails, press the locking tab to release,

and slide the middle rail into the outer rail.

7. Working with the le rail and le side of the chassis, insert the hooks in the front surface

of the outer rail into holes in the front of the rack and press the rail down to fasten it to the

rack.

8. Repeat with the right rail and right side of the chassis.

9. Working with the le and right rails, shorten or extend the outer rail as necessary to insert

the hooks in the back surface of the outer rail into holes in the back of the rack and press

the rail down to fasten it to the rack.

10. Secure the rails with one screw through the front and rear of each rail.

11. On both rails, pull the middle rail forward until it locks.

12. Lock the shuttle on the middle rail at the front of the middle rail.

13. Make sure that the ReadyNAS chassis is oriented right side up.

14. Using two people, align the inner rails on the chassis with the middle rails and then, pushing

evenly on both sides, push the inner rail into the middle rail and ball bearing shuttle until

both sides lock into the rail in a fully extended position.

15. Simultaneously, depress the locking tabs on both sides of the chassis and push it evenly all

the way into the rack.

Install Cable Management

The cable management hardware folds when the unit is pushed toward the back of the rack,

and straightens as the unit moves forward. If you attach the cables to the cable management

hardware, the cables also fold or straighten as the unit is moved in the rack, which eliminates

the tugging by the cables on the connectors on the unit.

The cable management kit consists of the cable management arm assembly with attached

chassis bracket and rack bracket, and the parts kit.

¾To install the cable management hardware:

1. Attach the rack bracket to the arm assembly using three bolts.

2. Attach the chassis bracket to the bracket on the le rear of the RR4360 chassis using two

bolts.

3. Attach the rack bracket to the le rear post of the rack using two bolts. Align the rack

bracket so that the lower bolt is 9 rack positions above the rail attachments.

On some racks, a screw driver with a sha longer than the rack bracket can make this step

easier. Alternatively, you can place the bracket on the outside of the rack rail and a second

person can drive the screws from inside the rack.

Aer fully cabling the ReadyNAS server, use cable ties to attach the cables to the arm assembly.

arm assembly

Parts kit

rack bracket

chassis bracket

Install Disks

Install at least one, and up to 60, disks before powering on your ReadyNAS for the ﬁrst time.

If you install previously formatted disks, you must use your ReadyNAS to reformat them the

ﬁrst time you power on the system. For information about reformatting disks, see Reformat

Disks on page 10.

Note: Reformatting disks deletes all data on the disks.

When you power on your system for the ﬁrst time or if you reset your system to its

factory default settings, the optimal RAID mode and level are automatically selected for

you based on the number of disks that are installed. If desired, you can later change the

RAID settings manually. For information about RAID settings, including changing RAID

settings, see the ReadyNAS OS 6 Soware User Manual. A link to this manual is available at

www.netgear.com/support/product/ReadyNAS_OS_6 or through a link in the product’s user

interface.

¾To install your disks:

1. Pull the chassis forward so that panel on the top front of the chassis is clear of the rack.

2. Press the front pair of release buttons on the sides of the chassis and push the top cover

toward the front until you can li it o.

PUSH

3. Insert your drives into the tool-less disk brackets supplied with the RR4360 server to hold

your disks in the server.

The ﬁgure shows the bracket tabs that align with the mounting holes in your drive.

Note: The following ﬁgure illustrates how disk numbers are assigned based on their position in the

chassis.

When you reinsert the drive and tray into a slot, the weight of the drive seats the drive.

Basic Setup

Aer you follow these instructions, your ReadyNAS is ready to use in a production environment.

Setup takes approximately 15 minutes.

¾To set up your storage system:

1. Install all available disks that you want to use in your ReadyNAS system.

Note: If you are using previously formatted disks that contain data, you must reformat these

disks before continuing. See Reformat Disks on page 8.

For a list of supported disks, see the Hardware Compatibility List at

netgear.com/readynas-hcl.

For information about installing disks, see the hardware manual for your system or visit

www.youtube.com/watch?v=hLiu0VeXd-Y.

2. Place your system in a location that provides adequate ventilation.

High-capacity disks can produce considerable heat. It is important to ensure that the

fan exhausts are unobstructed. For a complete list of placement considerations, see the

hardware manual for your system.

3. Connect a power cord to each power supply and plug the power cords into a wall outlet or

power strip.

Note: RR4360 systems require at least two power supplies.

4. Use an Ethernet cable to connect an Ethernet port on the storage system to your network.

5. If necessary, press the Power button to turn on the system.

6. Wait for the Power LED to turn solid blue.

7. Visit www.netgear.com/raidar to download and install the NETGEAR RAIDar utility.

Download RAIDar to a computer connected to the Internet and transfer the downloaded ﬁle

to the computer on the same LAN as your ReadyNAS system.

8. Start RAIDar.

RAIDar scans your local broadcast domain for your ReadyNAS. The broadcast domain is your

local network plus any networks reachable through a switch or repeater, but not through a

router.

9. Select your ReadyNAS in the RAIDar window.

10. Click the Setup button.

Note: Depending on your browser settings, you might get a message such as “This Connection is

Untrusted.” Select the options to continue connecting.

The Authentication Required window opens.

11. Log in to your ReadyNAS.

Enter admin for the user name, enter password for the password, and click the OK button.

The ReadyNAS local admin page displays in your browser and launches a setup wizard.

12. Follow the prompts of the setup wizard to conﬁgure your ReadyNAS system.

The setup process is complete. You can begin using your ReadyNAS storage system.

Reformat Disks

If you are using previously formatted disks that contain data, you must reformat the disks

before you can use them with your ReadyNAS system.

WARNING: This process erases all data and reformats all disks into a single RAID volume. If you want to

preserve the data on the disks, you must back up the data to an external drive before using the disks in

your ReadyNAS storage system.

¾To reformat previously formatted disks:

1. If your system is powered on, gracefully power o the system.

See Additional Information on page 10.

2. Install the previously formatted disks.

For a list of supported disks, see the Hardware Compatibility List at

kb.netgear.com/app/answers/detail/a_id/20641.

For information about installing disks, see the hardware manual for your system.

3. Press and hold the Reset button.

4. Press the Power button.

The system powers on.

5. Continue pressing the Reset button for about ﬁve seconds until the system enters the boot

menu, and then release it:

The front panel lights LED 1, LED 2, and LED 3 blink.

6. Press and hold the Reset button for about one second, and then release to scroll to the

next boot mode menu item.

7. Repeat the press, hold, and release of the Reset button until LED 2 is lit, and LED 1 and LED

3 are o.

8. Press and hold the Reset button for about four seconds to initiate a factory reset.

The system initiates a short disk test that takes 2 to 5 minutes.

Then, a 10-minute time-out period begins. Aer 10 minutes, the factory default process

starts.

The system returns to its factory default settings and reformats all installed disks for use

with ReadyNAS OS 6.

When the factory default process is complete, the reformatted disks are ready to use with your

system.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere NETGEAR Lagerung Handbücher

NETGEAR

NETGEAR ReadyNAS Duo Bedienungsanleitung

NETGEAR

NETGEAR SC101 - Storage Central NAS Server Bedienungsanleitung

NETGEAR

NETGEAR RND2110v2 Bedienungsanleitung

NETGEAR

NETGEAR ReadyNAS 102 Bedienungsanleitung

NETGEAR

NETGEAR ReadyNAS NVX Bedienungsanleitung

NETGEAR

NETGEAR ReadyNAS RMEM04 Bedienungsanleitung

NETGEAR

NETGEAR ReadyDATA OS 1.3 Desktop Storage Systems Bedienungsanleitung

NETGEAR

NETGEAR SC101T - Storage Central Turbo Network Drive Bedienungsanleitung

NETGEAR

NETGEAR SC101 - Storage Central NAS Server Bedienungsanleitung

NETGEAR

NETGEAR ReadyNAS NV+ Bedienungsanleitung

NETGEAR

NETGEAR ReadyNAS 2120 Bedienungsanleitung

NETGEAR

NETGEAR ReadyNAS OS 6 Desktop Storage Systems Bedienungsanleitung

NETGEAR

NETGEAR SC101 - Storage Central NAS Server Bedienungsanleitung

NETGEAR

NETGEAR SC101T - Storage Central Turbo Network Drive Installationsanleitung

NETGEAR

NETGEAR SC101 - Storage Central NAS Server Bedienungsanleitung

NETGEAR

NETGEAR ReadyNAS Duo Bedienungsanleitung

NETGEAR

NETGEAR ReadyNAS Duo Bedienungsanleitung

NETGEAR

NETGEAR RND2210-100NAS - Readynas Duo 2TB Desktop... Bedienungsanleitung

NETGEAR

NETGEAR SC101 - Storage Central NAS Server Bedienungsanleitung

NETGEAR

NETGEAR ReadyNAS RAIDiator 4.2 Bedienungsanleitung

NETGEAR

NETGEAR RND44751G - ReadyNAS NV+ NAS Server Bedienungsanleitung

NETGEAR

NETGEAR ReadyNAS 2120 v2 Bedienungsanleitung

NETGEAR

NETGEAR SC101 - Storage Central NAS Server Bedienungsanleitung

NETGEAR

NETGEAR RN12P0610-100NAS - ReadyNAS 3200 RN12P0610 NAS... Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung

HP P9000 Bedienungsanleitung