NETGEAR SC101 - Storage Central NAS Server Installationsanleitung

)NSTALLATION'UIDE

Storage Central SC101T

Installation Overview

Estimated Completion Time: 30 minutes.

When you finish the installation, your network will resemble this illustration.

The version 2.x software can manage both the SC101T and the older SC101 units.

Important: If you have an existing SC101, be sure to first remove the SC101

version 1.x software from every PC that has it installed.

The instructions below will guide you through these basic installation steps:

1. Install the Storage Central SC101T software. If you have an existing SC101,

use the new SC101T version 2.x software to update the old SC101 unit before

attaching the SC101T to your network.

2. Install a hard disk, and connect the Storage Central SC101T to your network.

3. Allocate disk space for each PC that will use the SC101T or SC101 units.

Preparing for Installation

• You must have an SATA hard disk, an Ethernet network with an available

port, DHCP must be running in the network, and you need to have either

Windows XP (SP2) or Windows 2000 (SP4) PCs to access the SC101T.



• Unpack the unit, Ethernet cable, power adapter, and the NETGEAR CD. The

CD contains driver software, a setup wizard, and links to online resources.

Remove the protective plastic film from the unit and familiarize yourself with

your new Storage Central SC101T. The back panel has information about the

ports and the status lights located on the front panel.

• When you set up the unit, stand it on its feet, and be sure it has ample

ventilation. Avoid putting the unit in a location where it could be knocked

over easily. Do not place items on top of it.

First, Install the SC101T Software

Note: This software must be installed on each PC that will

access the Storage Central Node.

1. Insert the NETGEAR

CD into your PC. If

this screen does not

appear, run

Autorun.exe on the

CD. Click Install

Software.

2. Click Check for

Updates and proceed according to the prompts. If Windows logo certification

warnings appear, click Continue to proceed.

If prompted to do so, be sure to remove existing SC101 software.

Follow the Windows New Hardware Found

prompts to complete the installation of several

software driver components. You will see the

Storage Central Manager icon on your

desktop.

3. Run the Storage Central Manager, which can

also check for updates.

Note: Only the Storage Central Manager can update SC101 or SC101T firmware.

Important: If you have an existing SC101 unit in your network, use the Storage

Central Manager version 2.x software you just installed to update the

SC101 firmware before you connect the SC101T or add new SC101

to your network.

Now, Install a Disk and Connect the SC101T

Warning: Be sure the SC101T power

cord is unplugged before

adding or removing the disks.

Failure to observe this

precaution could render your

disks useless.

These instructions explain how to set up a

single disk. Repeat these steps to install a

second disk.

1. Remove the front cover.

Note: The SC101T formats hard disks differently than a PC does. Do not swap

hard disks between a SC101T and a PC: the data will be unreadable.

2. Insert a hard disk.

• Position the disk with the bottom

facing in.

• Slide the disk into either slot.

• Replace the front cover

3. Connect the SC101T to your network.

Connect the provided Ethernet cable to

your network and to the back of the

SC101T. Be sure your network is running.

DHCP must be available in the network.

DHCP is usually enabled on home

networks by default.

D-shaped

power socket

January 10, 2007

United States and/or other countries. Other brand and product names are trademarks or registered trademarks of

4. Turn on the SC101T

Plug in the power adapter to a power

source and connect the other end to the

SC101T. Turn the unit on. View the front

panel to verify that the green power light

and the green network light are on.

Allocate Storage

Note: If you enable sharing, each computer on the

network that will share the drive must have

the SC101T software installed.

1. Run the Storage Central Manager utility

and select the Wizard Setup option.

2. Click Next to proceed. Follow the on-screen

prompts to allocate storage for this PC, setting the size, name, password, and

sharing options.

When the wizard is complete, this PC will now have a new drive available

that you will see in the Windows Explorer with the drive letter Windows

assigned.

3. Verify that you can copy files to and from you new SC101T drive.

4. Repeat these steps for each PC that will use the SC101T drives.

Refer to the manual for instructions on how to use advanced features such as

mirroring.

Important: The Storage Central unit is not a substitute for a data backup and

recovery system. Refer to the user manual for more information on

setting up backup and recovery systems.

Troubleshooting Tips

Here are some tips for correcting simple problems you may have.

Always restart your network in this sequence:

1. Turn off and unplug the modem, turn off the router, shut off the SC101T, and

shut down the computers.

2. Plug in and turn on the cable or DSL modem. Wait about 2 minutes.

3. Turn on the router. Wait about 1 minute.

4. Turn on the SC101T.

5. Turn on the computers.

Check the status lights to verify correct operation.

When powered on, the SC101T power light will be on. When connected to an

operational Ethernet network, the Ethernet status light will be lit. The label on the

SC101T back panel identifies these status lights.

Update the firmware of an existing SC101 you may have before

adding a SC101T to your network.

Be sure to use the new version 2.x Storage Central Manager software to update the

firmware of an existing SC101 before you add a SC101T to your network.

Technical Support

You can register your product on the website or over the phone. The phone

numbers for worldwide regional customer support centers are on the Warranty and

Support Information card that came with your product. Locate the serial number

on the bottom label of your product and use it to register your product at

http://www.NETGEAR.com/register.

Go to http://kbserver.netgear.com for product updates and Web support.

Hard Drive Not Included

A hard drive is not included with this NETGEAR product. You are solely

responsible for the selection, purchase and installation of your own hard drive. By

using this NETGEAR product, you understand and agree that (i) NETGEAR is

not warranting your hard drive or its contents; and (ii) NETGEAR is not

responsible under any circumstances for any damage to or loss of contents that

results from the misuse or failure of any hard drive with the NETGEAR product,

regardless of the cause of such damage or loss. In certain circumstances data loss

may be permanent and unrecoverable and therefore you are highly encouraged to

separately maintain a backup copy of any data that you store on such hard

drive(s).

Andere Handbücher für SC101 - Storage Central NAS Server

Dieses Handbuch passt für folgende Modelle

Andere NETGEAR Lagerung Handbücher

NETGEAR

NETGEAR SC101 - Storage Central NAS Server Bedienungsanleitung

NETGEAR

NETGEAR SC101T - Storage Central Turbo Network Drive Installationsanleitung

NETGEAR

NETGEAR ReadyDATA OS 1.3 Desktop Storage Systems Bedienungsanleitung

NETGEAR

NETGEAR RN12P1210-100NAS - ReadyNAS 3200 RN12P1210 NAS... Bedienungsanleitung

NETGEAR

NETGEAR ReadyNAS RR4360X Bedienungsanleitung

NETGEAR

NETGEAR ReadyNAS Duo Bedienungsanleitung

NETGEAR

NETGEAR ReadyNAS Duo Bedienungsanleitung

NETGEAR

NETGEAR RND2210-100NAS - Readynas Duo 2TB Desktop... Bedienungsanleitung

NETGEAR

NETGEAR SC101 - Storage Central NAS Server Bedienungsanleitung

NETGEAR

NETGEAR ReadyNAS NV+ Bedienungsanleitung

NETGEAR

NETGEAR RND44751G - ReadyNAS NV+ NAS Server Bedienungsanleitung

NETGEAR

NETGEAR SC101T - Storage Central Turbo Network Drive Bedienungsanleitung

NETGEAR

NETGEAR ReadyRECOVER Montage- und Bedienungsanleitung

NETGEAR

NETGEAR ReadyNAS 2120 v2 Bedienungsanleitung

NETGEAR

NETGEAR RN12P0610-100NAS - ReadyNAS 3200 RN12P0610 NAS... Bedienungsanleitung

NETGEAR

NETGEAR ReadyNAS 102 Bedienungsanleitung

NETGEAR

NETGEAR ReadyNAS RMEM04 Bedienungsanleitung

NETGEAR

NETGEAR RNDP200U-100NAS Bedienungsanleitung

NETGEAR

NETGEAR ReadyNAS NVX Bedienungsanleitung

NETGEAR

NETGEAR ReadyNAS Duo Bedienungsanleitung

NETGEAR

NETGEAR ReadyNAS NV+ Bedienungsanleitung

NETGEAR

NETGEAR RN12P1210-100NAS - ReadyNAS 3200 RN12P1210 NAS... Bedienungsanleitung

NETGEAR

NETGEAR ReadyNAS RAIDiator 4.2 Bedienungsanleitung

NETGEAR

NETGEAR MA701 - 802.11b 11 Mbps Compact Flash Card Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung

HP P9000 Bedienungsanleitung