NETGEAR XSM7224S - ProSafe 10 Gigabit Stackable Handbuch

350 East Plumeria Drive

San Jose, CA 95134

USA

November 2010

202-10751-01

v1.0

Managed Stackable Switch

XSM7224S

Hardware Installation Guide

Managed Stackable Switch XSM7224S

No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated

into any language in any form or by any means without the written permission of NETGEAR, Inc.

P/N: Part Number TBD v1.0

Technical Support

When you register your product at http://www.netgear.com/register, we can provide you with faster expert technical

support and timely notices of product and software upgrades.

NETGEAR, Inc.

350 East Plumeria Drive

San Jose, CA 95134 USA

E-mail: [email protected]

Website: http://www.netgear.com

Phone: 1-888-NETGEAR, for US & Canada only. For other countries, see your Support information card.

Trademarks

NETGEAR, the NETGEAR logo, ProSafe, Smart Wizard, and Auto Uplink are trademarks or registered

trademarks of NETGEAR, Inc. Microsoft, Windows, Windows NT, and Vista are registered trademarks of Microsoft

Corporation. Other brand and product names are registered trademarks or trademarks of their respective holders.

Statement of Conditions

To improve internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes

to the products described in this document without notice. NETGEAR does not assume any liability that may occur

due to the use or application of the product(s) or circuit layout(s) described herein.

Revision History

Publication Part Number Version Publish Date

202-10751-01 v1.0 November 2010

Table of Contents |3

Chapter 1 Introduction

XSM7224S Front Panel and LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

XSM7224S Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Chapter 2 Hardware Installation

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Protecting Against Electrostatic Discharge . . . . . . . . . . . . . . . . . . . . . . . . . 8

Unpacking the Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Select a Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Install the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Check the Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Connect to Power and Check the LEDs . . . . . . . . . . . . . . . . . . . . . . . . 11

Fan Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Installing an Adapter and Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Creating a Stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Power Module Bay. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Installing a Power Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Removing a Power Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Connecting Equipment to the Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

RJ-45 Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Connecting a Console to the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Chapter 3 Troubleshooting

Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Additional Troubleshooting Suggestions . . . . . . . . . . . . . . . . . . . . . . . . . 19

Appendix A Technical Specifications

Specifications for XSM7224S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Specifications for GSM7328S and GSM7352S . . . . . . . . . . . . . . . . . . . . . 23

Appendix B Default Configuration Settings

Appendix C Notification of Compliance

Table of Contents

4|Contents

Managed Stackable Switch XSM7224S

Chapter 1. Introduction |5

1. Introduction

The NETGEAR ProSafe 10Gigabit Managed L2+ Stackable Switch XSM7224S is a

state-of-the-art, high-performance, IEEE-compliant network solution. It includes powerful

management features that you can use to eliminate bottlenecks, boost performance, and

increase productivity.

This guide describes hardware installation and basic troubleshooting for the XSM7224S Switch

This switch can be free-standing, or rack-mounted in a wiring closet or an equipment room. For

information about features for each product, see the NETGEAR website at

http://www.netgear.com.

XSM7224S Front Panel and LEDs

The following figure shows the front panel of the XSM7224S. The front panel contains LEDs,

a Reset button, a USB port, copper/fiber combo ports, and 10G SFP+ ports. The module

bays support any combination of ProSafe 10GBase-SR SFP+ Module AXM761, ProSafe

10GBase-LR SFP+ Module AXM762, or ProSafe 10GBase-LRM SFP+ Module AXM763.

See SFP+ Modules in Chapter 2.

Figure 1. XSM7224S Front Panel

LEDs

Reset button SFP+ Ports Combo Ports

USB Port

Console Port

6|Chapter 1. Introduction

Managed Stackable Switch XSM7224S

Table 1. LED Descriptions for XSM7224S

LED Description

ID This is the stack member ID (1–99) that the software assigns to the switch.

Stack Master • Green: The switch acts as a master unit in a stack of XSM7224S series

switches.

• Off: The switch acts as a slave unit in a stack of XSM7224S series switches.

Power • Solid green: The power module is present, is supplying power to the switch, and

is working normally.

• Solid yellow: The system is in boot-up stage.

• Blinking yellow: Power module is present but has failed.

• Off: Power is disconnected.

Fan • Solid green: The fan is operating normally.

• Solid yellow: The fan has failed.

• Off: No fan is detected.

10GBT Ports

(2 LEDs per port) 10/100M Link/ACT LED:

• Off: No 10/100M link is established on the port.

• Solid yellow: A valid 10/100M link is established on the port.

• Blinking yellow: The port is transmitting or receiving packets at 10/100Mbps.

Left side LED

1G/10G Link/ACT LED:

• Off: No 1G/10G link is established on the port.

• Solid Green – A valid 10Gbps link is established on the port.

• Blinking Green – Packet transmission or reception is occurring on the port at

10Gbps.

• Solid Yellow – A valid 1000Mbps link is established on the port.

• Blinking Yellow – Packet transmission or reception is occurring on the port at

1000Mbps.

Note: If port 21–24 media is changed to SFP+, the RJ-45 LEDs change to OFF

status.

SFP+ Ports

(1 SPD/Link/ACT

LED per port)

• Off: No SFP/SFP+ module link is established on the port.

• Solid green: A valid 10Gbps SFP+ module link is established on the port.

• Blinking green: The port is transmitting or receiving packets at 10Gbps.

• Solid yellow: A valid 1Gbps SFP module link is established on the port.

• Blinking yellow: Packet transmission or reception is occurring on the port at

1Gbps.

Note: If port 21–24 media is changed to copper, the SFP+ LEDs change to Off

status.

Right side LED

Chapter 1. Introduction |7

Managed Stackable Switch XSM7224S

XSM7224S Rear Panel

The rear panel has two fan trays, a power supply connector, a replaceable power supply, and

a bay for for an optional redundant power supply (APS300W).

Figure 2. XSM7224S Rear Panel

Safety Instructions

Use the following safety guidelines to ensure your own personal safety and to help protect

your system from potential damage.

To reduce the risk of bodily injury, electrical shock, fire, and damage to the equipment,

observe the following precautions.

• Observe and follow service markings.

- Do not service any product except as explained in your system documentation.

- Opening or removing covers that are marked with the triangular symbol with a

lightning bolt may expose you to electrical shock. Only a trained service

technician should service components inside these compartments.

• If any of the following conditions occur, unplug the product from the electrical outlet and

replace the part or contact your trained service provider:

- The power cable, extension cable, or plug is damaged.

- An object has fallen into the product.

- The product has been exposed to water.

- The product has been dropped or damaged.

- The product does not operate correctly when you follow the operating instructions.

• Keep your system away from radiators and heat sources. Also, do not block cooling

vents.

• Do not spill food or liquids on your system components, and never operate the product in

a wet environment. If the system gets wet, see the appropriate section in your

troubleshooting guide or contact your trained service provider.

• Do not push any objects into the openings of your system. Doing so can cause fire or

electric shock by shorting out interior components.

Replaceable

AC Power

Connector

Power Supply

Replaceable

Fan TraysSupply Bay

Optional Power

8|Chapter 1. Introduction

Managed Stackable Switch XSM7224S

• Use the product only with approved equipment.

• Allow the product to cool before removing covers or touching internal components.

• Operate the product only from the type of external power source indicated on the

electrical ratings label. If you are not sure of the type of power source required, consult

your service provider or local power company.

• To help avoid damaging your system, be sure that the voltage selection switch (if

provided) on the power supply is set to match the power available at your location:

- 115 volts (V), 60 hertz (Hz) in most of North and South America and some Far

Eastern countries such as South Korea and Taiwan

- 100 V, 50 Hz in eastern Japan and 100 V, 60 Hz in western Japan

- 230 V, 50 Hz in most of Europe, the Middle East, and the Far East

• Also, be sure that attached devices are electrically rated to operate with the power

available in your location.

• Use only approved power cables. If you have not been provided with a power cable for

your system or for any AC powered option intended for your system, purchase a power

cable that is approved for use in your country. The power cable must be rated for the

product and for the voltage and current marked on the product's electrical ratings label.

The voltage and current rating of the cable should be greater than the ratings marked on

the product.

• To help prevent electric shock, plug the system and peripheral power cables into properly

grounded electrical outlets.

• The peripheral power cables are equipped with three-prong plugs to help ensure proper

grounding. Do not use adapter plugs or remove the grounding prong from a cable. If you

must use an extension cable, use a three-wire cable with properly grounded plugs.

• Observe extension cable and power strip ratings. Make sure that the total ampere rating

of all products plugged into the extension cable or power strip does not exceed 80

percent of the ampere ratings limit for the extension cable or power strip.

• To help protect your system from sudden, transient increases and decreases in electrical

power, use a surge suppressor, line conditioner, or uninterruptible power supply (UPS).

• Position system cables and power cables carefully; route cables so that they cannot be

stepped on or tripped over. Be sure that nothing rests on any cables.

• Do not modify power cables or plugs. Consult a licensed electrician or your power

company for site modifications.

• Always follow your local and national wiring rules.

Chapter 2. Hardware Installation |9

2. Hardware Installation

This chapter explains how to install the hardware for the Managed Stackable Layer 2+ 10G

Switch XSM7224S.

Package Contents

Each switch is packed and shipped separately. The package contains the following items:

• Managed Stackable Layer 2+ 10Gigabit Ethernet Switch with preinstalled software

• Power cord

• USB to serial converter

• Rubber footpads for tabletop installation

• Rubber caps for the SFP+ sockets

• Rack-mounting kit

• Null-modem serial cable (RS-232) with 9-pin connectors

• Resource CD: The CD either includes these documents or links to access them:

- ProSafe 7200 Managed Switch CLI Manual, Version 9.0

- NETGEAR 7000 Series Managed Switch Administration Guide

- NETGEAR Installation Guide for the XSM7224S Stackable Managed Switch

- This Hardware Installation Guide

• ProSafe NMS100 Network Management System 30-day trial CD-ROM

Protecting Against Electrostatic Discharge

WARNING!

Static electricity can harm delicate components inside your

system. To prevent static damage, discharge static electricity

from your body before you touch any of the electronic

components, such as the microprocessor. You can do so by

periodically touching an unpainted metal surface on the switch.

10 |Chapter 2. Hardware Installation

Managed Stackable Switch XSM7224S

You can also take the following steps to prevent damage from electrostatic discharge (ESD):

1. When unpacking a static-sensitive component from its shipping carton, leave it in the

antistatic package until you are ready to install it. Just before unwrapping the antistatic

package, discharge static electricity from your body.

2. Before moving a sensitive component, place it in an antistatic container or package.

3. Handle all sensitive components in a static-safe area. If possible, use antistatic floor pads,

workbench pads, and an antistatic grounding strap.

Unpacking the Hardware

Check the contents of the boxes to make sure that all items are present before installing the

switch.

1. Place the container on a clean flat surface and cut all straps securing the container.

2. Unpack the hardware from the boxes.

Carefully remove the hardware and place it on a secure and clean surface. See

<pdf>“Select a Location” on page 2-10.

3. Remove all packing material.

4. Make sure that all items are present. See “Package Contents” on page -9.

Note: If any item is found missing or damaged, contact your local

NETGEAR reseller for replacement.

5. Inspect the products and accessories for damage. Report any damage immediately.

Installation

Install the equipment in the sequence presented in this section:

1. Select a Location. See “Select a Location” on page -10.

2. Install the Switch. See “Install the Switch” on page -11.

3. Check the installation. See “Check the Installation” on page -12.

4. Apply power and check the LEDs. See “Connect to Power and Check the LEDs” on

page -12.

Select a Location

The switch can be mounted in a standard 19-inch (48.26-centimeter) rack, wall-mounted, or

left freestanding (placed on a tabletop).

Andere Handbücher für XSM7224S - ProSafe 10 Gigabit Stackable

Inhaltsverzeichnis

Andere NETGEAR Schalten Handbücher

NETGEAR

NETGEAR GSM7228PS-100NAS Handbuch

NETGEAR

NETGEAR GS728TPv2 Bedienungsanleitung

NETGEAR

NETGEAR FS728TPv1 - ProSafe 24 Port 10/100 Smart... Stücklistenhandbuch

NETGEAR

NETGEAR GS408EPP Bedienungsanleitung

NETGEAR

NETGEAR GS716T - ProSafe Switch Bedienungsanleitung

NETGEAR

NETGEAR FE508 - Hub Bedienungsanleitung

NETGEAR

NETGEAR GSM7248R - ProSafe Switch Betriebsanleitung

NETGEAR

NETGEAR FSM726E - ProSafe Switch Bedienungsanleitung

NETGEAR

NETGEAR ProSafe GS116 Bedienungsanleitung

NETGEAR

NETGEAR FSM7328S - ProSafe Switch Bedienungsanleitung

NETGEAR

NETGEAR FSM726v3 - ProSafe Fast Ethernet L2 Managed... Bedienungsanleitung

NETGEAR

NETGEAR GSM712F - Managed Fiber Gigabit Switch Bedienungsanleitung

NETGEAR

NETGEAR ProSAFE M4300 series Bedienungsanleitung

NETGEAR

NETGEAR FS208 Bedienungsanleitung

NETGEAR

NETGEAR GS724Tv3 - ProSafe Gigabit Managed Switch Bedienungsanleitung

NETGEAR

NETGEAR GS108X Bedienungsanleitung

NETGEAR

NETGEAR FSM726 - ProSafe Managed Switch Bedienungsanleitung

NETGEAR

NETGEAR ProSafe GSM7324 Bedienungsanleitung

NETGEAR

NETGEAR GSM7248R - ProSafe Switch Bedienungsanleitung

NETGEAR

NETGEAR GS116 - ProSafe 16 Port Gigabit Desktop... Bedienungsanleitung

NETGEAR

NETGEAR FSM726S Bedienungsanleitung

NETGEAR

NETGEAR M4100 Series ProSAFE Bedienungsanleitung

NETGEAR

NETGEAR SW518 - Switch Bedienungsanleitung

NETGEAR

NETGEAR ProSafe XS712T Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung