NETGEAR WG602v4 - Wireless Access Point Handbuch

)NSTALLATION'UIDE

NETGEAR WG602v454 Mbps Wireless Access Point

Start Here

Please refer to the Reference Manual on your Resource CD for instructions on advanced

configuration options.

Estimated Completion Time: 30 minutes.

Tip: Before mounting the WG602v4in a high location, first set up and test the WG602v4

to verify wireless network connectivity.

First, Set Up the WG602v4

1. Connect the wireless access point to your computer and

modem

a. Unpack the box and verify the contents.

b. Prepare a PC with an Ethernet

adapter. If this PC is already part

of your network, record its

TCP/IP configuration settings.

Configure the PC with a static IP

address of 192.168.0.210 and

255.255.255.0 as the Subnet Mask.

c. Connect an Ethernet cable from

the WG602v4to the PC (point A

in the illustration).

d. Securely insert the other end of the

cable into the WG602v4Ethernet

port (point B in the illustration).

Ethernet

Port

Blue NETGEAR

Cable

WG602v4

Computer

e. Turn on your computer, connect the power adapter to the WG602v4and verify

the following:

• The power light should be lit. If the power light is not lit, check the

connections and check to see if the power outlet is controlled by a wall

switch that is turned off.

• The LAN light on the WG602v4should be lit (amber for a 10 Mbps

connection and green for a 100 Mbps connection). If not, make sure the

Ethernet cable is securely attached at both ends.

•The WLAN light should be lit.

2. Configure LAN and Wireless Access

a. Configure the WG602v4Ethernet port for LAN access.

• Connect to the WG602v4by opening your browser and

entering http://192.168.0.227 in the address field.

• When prompted, enter admin for the user name and

password for the password, both in lower case letters.

• Click the Basic Settings link and configure the IP Settings for your network.

b. Configure the wireless interface for wireless access. See the online help or the

Reference Manual for full instructions.

c. Test wireless connectivity using a PC with a wireless adapter configured

according to the wireless settings you just set in the WG602v4to establish a

wireless connection to the WG602v4.

Now that you have finished the setup steps, you are ready to deploy the WG602v4in

your network. If needed, you can now reconfigure the PC you used in step 1 back to

its original TCP/IP settings.

227

Deploy the WG602v4

1. Disconnect the WG602v4and position it where you will deploy it. The best location

is elevated, such as wall mounted or on the top of a cubicle, at the center of your

wireless coverage area, and within line of sight of all the mobile devices.

2. Position the antenna. Vertical positioning provides best side-to-side coverage.

Horizontal positioning provides best top-to-bottom coverage.

3. Connect an Ethernet cable from your WG602v4Access Point to a LAN port on your

router, switch, or hub.

4. Connect the power adapter to the wireless access point and plug the power adapter in

to a power outlet. The PWR, LAN, and WLAN lights should light up.

Tip: The WG602v4supports Power Over Ethernet (PoE). If you have a switch that

provides PoE, you will not need to use the power adapter to power the WG602v4.

This can be especially convenient when the WG602v4is installed in a high location

far away from a power outlet.

Now, Verify Wireless Connectivity

Using a computer with an 802.11g or 802.11b wireless adapter, verify connectivity by

using a browser such as Netscape® or Internet Explorer to connect to the Internet, or

check for file and printer access on your network.

Note: If you cannot connect, see to Troubleshooting Tips in this guide or the Reference

Manual on the Resource CD for the ProSafe Wireless Access Point.

February 2005

Troubleshooting Tips

Here are some tips for correcting simple problems you may have.

No lights are lit on the access point.

The access point has no power.

• Make sure the power cord is connected to the access point and plugged in to a

working power outlet or power strip.

• Make sure you are using the correct NETGEAR power adapter supplied with your

access point.

The Ethernet light is not lit.

There is a hardware connection problem.

• Make sure the cable connectors are securely plugged in at the access point and the

network device (hub, switch, or router).

• Make sure the connected device is turned on.

The WLAN light is not lit.

The access point’s antennas are not working.

• If the Wireless LAN activity light stays off, disconnect the adapter from its power

source and then plug it in again.

• Make sure the antennas are tightly connected to the WG602v4.

• Contact NETGEAR if the WLAN light remains off.

I cannot configure the access point from a browser.

Check these items:

• The WG602v4is properly installed, LAN connections are OK, and it is powered on.

Check that the LAN port LED is green to verify that the Ethernet connection is OK.

• If you are using the NetBIOS name of the WG602v4to connect, ensure that your PC

and the WG602v4are on the same network segment or that there is a WINS server on

your network.

• If your PC uses a Fixed (Static) IP address, ensure that it is using an IP Address in the

range of the WG602v4. The WG602v4default IP Address is 192.168.0.227 and the

default Subnet Mask is 255.255.255.0. The WG602v4default setting is for a static IP

address. If the network where you are connecting it is using DHCP, configure it

accordingly. See the Reference Manual on the Resource CD for the ProSafe Wireless

Access Point for more details.

I cannot access the Internet or the LAN with a wireless capable

computer.

There is a configuration problem. Check these items:

• You may not have restarted the computer with the wireless adapter to have TCP/IP

changes take effect. Restart the computer.

• The computer with the wireless adapter may not have the correct TCP/IP settings to

communicate with the network. Restart the computer and check that TCP/IP is set up

properly for that network. The usual setting for Windows on the Network Properties

is set to “Obtain an IP address automatically.”

• The access point’s default values may not work with your network. Check the access

point default configuration against the configuration of other devices in your network.

• For full instructions on changing the access point’s default values, see the Reference

Manual on the Resource CD for the ProSafe Wireless Access Point.

Technical Support

Thank you for selecting NETGEAR products.

To register your product, go to: http://www.NETGEAR.com/register

Go to http://www.NETGEAR.com/support for support information.

NETGEAR is a registered trademark of NETGEAR, Inc. in the United States and/or other countries. Other brand

and product names are trademarks or registered trademarks of their respective holders. Information is subject to

change without notice.

Regulatory Approvals

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio communica-

tions. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

Consult the dealer or an experienced radio/TV technician for help.

To assure continued compliance, any changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority to operate this equipment.

(Example - use only shielded interface cables when connecting to computer or peripheral

devices).

FCC Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with a minimum distance of 20

centimeters between the radiator and your body.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause

undesired operation.

This transmitter must not be co-located or operating in conjunction with any other antenna or

transmitter.

The antennas used for this transmitter must be installed to provide a separation distance of at

least 20 cm from all persons and must not be co-located or operating in conjunction with any

other antenna or transmitter.

Channel

The Wireless Channel sets the radio frequency used for communication.

•Access Points use a fixed Channel. You can select the Channel used. This allows you to

choose a Channel which provides the least interference and best performance. In the USA

and Canada, 11 channel are available. If using multiple Access Points, it is better if adjacent

Access Points use different Channels to reduce interference.

• In "Infrastructure" mode, Wireless Stations normally scan all Channels, looking for an

Access Point. If more than one Access Point can be used, the one with the strongest

signal is used. (This can only happen within an ESS.)

• If using "Ad-hoc" mode (no Access Point), all Wireless stations should be set to use the

same Channel. However, most Wireless stations will still scan all Channels to see if there

is an existing "Ad-hoc" group they can join.

Note:This equipment marketed in USA is restricted by firmware to only operate on 2.4G channel 1-11

Andere Handbücher für WG602v4 - Wireless Access Point

Andere NETGEAR Drahtloser Zugangspunkt Handbücher

NETGEAR

NETGEAR ME102 - Wireless Access Point Bedienungsanleitung

NETGEAR

NETGEAR WiFi 6 AX1800 Bedienungsanleitung

NETGEAR

NETGEAR ProSAFE WNDAP380R Bedienungsanleitung

NETGEAR

NETGEAR WAC124 Bedienungsanleitung

NETGEAR

NETGEAR ProSafe WNAP320 Bedienungsanleitung

NETGEAR

NETGEAR SSL312 - ProSafe SSL VPN Concentrator 25 Bedienungsanleitung

NETGEAR

NETGEAR ProSafe Premium WNDAP660 Bedienungsanleitung

NETGEAR

NETGEAR ME103 - 802.11b ProSafe Wireless Access... Bedienungsanleitung

NETGEAR

NETGEAR WNAP210 Bedienungsanleitung

NETGEAR

NETGEAR WAC124 Bedienungsanleitung

NETGEAR

NETGEAR ProSafe Premium WNDAP660 Bedienungsanleitung

NETGEAR

NETGEAR WAC120 Bedienungsanleitung

NETGEAR

NETGEAR WAX610 Bedienungsanleitung

NETGEAR

NETGEAR SSL312 - ProSafe SSL VPN Concentrator 25 Montage- und Wartungsanleitung

NETGEAR

NETGEAR WAC730 Bedienungsanleitung

NETGEAR

NETGEAR WG602 - 54 Mbps Wireless Access Point Bedienungsanleitung

NETGEAR

NETGEAR WG602 - 54 Mbps Wireless Access Point Bedienungsanleitung

NETGEAR

NETGEAR ProSAFE WNDAP380R Bedienungsanleitung

NETGEAR

NETGEAR WAC510 Bedienungsanleitung

NETGEAR

NETGEAR WAC104 Bedienungsanleitung

NETGEAR

NETGEAR ProSafe Premium WNDAP620 Bedienungsanleitung

NETGEAR

NETGEAR ProSafe WNAP320 Bedienungsanleitung

NETGEAR

NETGEAR Orbi RBR40 Bedienungsanleitung

NETGEAR

NETGEAR WAG302v2 - ProSafe Dual Band Wireless Access... Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung