Nethix WE110 Bedienungsanleitung
•6.3. Factory reset
•6.4. Miscelaneous commands
•7. Safety guidelines
•8. Warranty and support
•9. Return and repair
1. Overview
WE110 is a SMS and RING based remote control. It provides a digital
input and an output relay that make it suitable for remotely control
gates, doors, windows and in general to automate any access.
Mounting the device is extremely simple thanks to its magnets. Other
mounting options are available.
Read also the WE110 we110_manual_thermostat.
2. Technical characteristics
Characteristic Description
Communications Integrated GSM/GPRS Quad band modem
SIM CARD reader included Provided with
GSM Dual band antenna
Inputs/Outputs 1 dry contact digital input
1 relay output (1A-230VAC)
LED One RGB LED
Button Activates the output relay. Normally used for
opening the gate
3 02/2016
Power supply Low tension 12-24VDC - 9-32VDC
Consumption Average 100mA, transmitting 400mA, max
pulsed 1,8A
Size (L x W x H) 40 x 23 x 85mm
Weight 52 gr
Storage
temperature -25°C - +85°C
Working
temperature -15°C - +55°C
Humidity 0% - 80% (non condensing)
3. Pinout and connection
PIN Description
1 Relay B
2 Relay A
3 Power source VAC1
4 Power source VAC2
4 02/2016
5 Input
6 GND
7 SIM card slot
8 LED
9 Button
4. Installation and setup
•Disable the PIN for the SIM card to be used in the WE110, using
a standard GSM cell phone. Refer to the phone user manual for
details.
• Insert the SIM card in the slot.
• Connect the output relay to the controlled gate or device.
•Screw the antenna provided in the SMA RF connector, then
connect power leads and power on the device.
System startup takes approximately 45 seconds, during which the
LED in the front side show diagnostic information as detailed in the
following table:
LED status at boot time
LED color Status Descriprtion
Fast blinking,
each 0.320s The WE110 is booting
Turned-on for 5
seconds, then
it will reboot
Network registration
error or SIM error
5 02/2016
Fast blinking
for 3 seconds From this moment, the
WE110 is fully
operative
LED status at normal operation
There are two normal conditions that are shown with two different LED
status
• The system LED (green)
• The signal LED (red or blue)
System LED
LED color Status Descriprtion
Turned-on The relay is closed
Turned-off The relay is opened
Signal LED
LED color Status Descriprtion
Turned-on The signal is good
Slow blinking,
each 0.60s The signal is sufficient
Slow blinking,
each 0.60s The signal is not good
For example if the relay is closed and there is a sufficient signal, the
LED status will blink in the following way:
6 02/2016
All setup and control activities of the device are carried out sending
and receiving SMS messages.
Note
The text in bold denotes strings to be typed and sent to the
device.
For example, ADD means that a SMS containing the word ADD
will be sent to the device.
The first operation to execute in a new WE110 is to define the
administrator phone number:
ADMIN +391112223333
From this moment it will be possible to configure WE110 by sending
SMS from only the ADMIN number.
Set the SMS service center of the SIM provider:
CENTER +393359609600
The following table shows the service center numbers of the most
relevant providers:
SMS service center numbers
Country Operator Number
7 02/2016
Italy TIM +39335960960
0
Italy Vodafone +39349200020
0
Italy Wind +39320585850
0
Now it is possible to add a user that will be enabled to call WE110:
ADD +391112223333
Adding two or more users can be done with the same command and
up to ten users can be added. Notice the space between the numbers:
ADD +391112223333 +394445556666
Similarly, it is possible to remove a user from WE110:
CANC +391112223333
Removing two or more users can be done with the same command
and up to ten users can be removed. Notice the space between the
numbers:
CANC +391112223333 +394445556666
Note
Only the administrator user can add or remove users
At any moment the administrator can obtain the list of registered
users:
LIST 1
With this command the administrator receives one SMS with the first
ten users.
8 02/2016
To receive the users 11 to 20, the administrator can send the
command:
LIST 2
and so on with the next users.
4.1. Front panel button
The button located in the front panel, when pressed for 3 seconds,
activates the relay.
5. Using the device: APP
The easiest way to program and use WE110 is by downloading the
app:
The app provides a configuration wizard and an user-friendly interface:
9 02/2016
10 02/2016
Inhaltsverzeichnis
Andere Nethix Thermostat Handbücher
Beliebte Thermostat Handbücher anderer Marken
EWELLY
EWELLY EW-181 Bedienungsanleitung
Prolon
Prolon T1100 Montageanleitung
Computherm
Computherm Q20 Bedienungsanleitung
Heatmiser
Heatmiser neoStat Bedienungsanleitung
Aube Technologies
Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung
Mars
Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung
