Network Technologies Incorporated VEEMUX Series Bedienungsanleitung

SM-nXm-15V-LCD

Video Matrix Switch

Installation and Operation Manual

VEEMUX®Series

NETWORK

TECHNOLOGIES

INCORPORATED

Tel:330-562-7070

Fax:330-562-1999

1275 Danner Dr

Aurora, OH 44202

www.networktechinc.com

NTI

MAN067 Rev Date 10/26/2017

TRADEMARK

VEEMUX is a registered trademark of Network Technologies Inc in the U.S. and other countries.

in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,

without the prior written consent of Network Technologies Inc, 1275 Danner Drive, Aurora, Ohio 44202.

CHANGES

The material in this guide is for information only and is subject to change without notice. Network Technologies Inc reserves the

right to make changes in the product design without reservation and without notification to its users.

FIRMWARE VERSIONS

Front Panel LCD Firmware Version 1.2

Ethernet Control Firmware Version 1.20

TABLE OF CONTENTS

Introduction....................................................................................................................................................................1

Basic Operation ...........................................................................................................................................................1

Supported Web Browsers............................................................................................................................................1

Compatibilty.................................................................................................................................................................1

Ordering Information....................................................................................................................................................1

SM-nXm-15V-LCD....................................................................................................................................................1

Options......................................................................................................................................................................1

Materials ......................................................................................................................................................................2

Cables..........................................................................................................................................................................2

Default User Name and Passwords ............................................................................................................................2

Features and Functions................................................................................................................................................3

Installation......................................................................................................................................................................4

Connect the Sources and Monitors .............................................................................................................................4

Connect RS232 ...........................................................................................................................................................5

Connect to the Ethernet...............................................................................................................................................5

Power Up.....................................................................................................................................................................6

LED Matrix......................................................................................................................................................................6

Control Options.............................................................................................................................................................7

Front Panel LCD with Keypad Control.........................................................................................................................7

Scan Mode................................................................................................................................................................8

RS232 Control .............................................................................................................................................................8

Remote Connection..................................................................................................................................................8

Baud Rate.................................................................................................................................................................9

Unit Address .............................................................................................................................................................9

Command Protocol...................................................................................................................................................9

Autostatus............................................................................................................................................................10

NTI Switch Control Program For Windows 9X, NT, 2000, XP, Vista And 7..............................................................11

SerTest- RS232 Interface Test Program...................................................................................................................11

Main Options...........................................................................................................................................................11

Matrix Operations....................................................................................................................................................11

Ethernet Operations................................................................................................................................................12

Setup Options.........................................................................................................................................................12

Ethernet Control..........................................................................................................................................................13

Telnet Interface-Port 2000.........................................................................................................................................13

Telnet Interface-Port 2005.........................................................................................................................................14

Command Summary...............................................................................................................................................14

Command Detail.....................................................................................................................................................15

RU-Read Unit Size ..............................................................................................................................................15

RO-Read Connection for Output Port .................................................................................................................15

CS- Connect Output Port to Input Port................................................................................................................15

CA- Connect All Output Ports to Input Port.........................................................................................................15

SS_01- Enable Auto Status Mode.......................................................................................................................16

SS_00- Disable Auto Status Mode......................................................................................................................16

SX- Examine connections ...................................................................................................................................17

Terminate telnet session .....................................................................................................................................17

Web Interface...............................................................................................................................................................18

Enter the Password.................................................................................................................................................18

Main Menu.................................................................................................................................................................19

Video Switch Page..................................................................................................................................................19

Administration Menu...............................................................................................................................................20

Setup Pages........................................................................................................................................................21

User Management...............................................................................................................................................22

Add User..............................................................................................................................................................22

Edit User..............................................................................................................................................................23

Video Input Names..............................................................................................................................................23

Output Names......................................................................................................................................................24

Outputs Scanning Sequences.............................................................................................................................24

Update Firmware.................................................................................................................................................26

Change Password Page.........................................................................................................................................27

Help Page ...............................................................................................................................................................27

Update Web Server ................................................................................................................................................27

Logout Page............................................................................................................................................................28

Device Discovery Tool................................................................................................................................................29

How to Use the Device Discovery Tool .....................................................................................................................29

Infrared Control ...........................................................................................................................................................30

Features And Functions.............................................................................................................................................30

Keypad....................................................................................................................................................................30

LCD Display............................................................................................................................................................30

How To Use The IRT.................................................................................................................................................31

Change the Switch..................................................................................................................................................31

Change Output Port................................................................................................................................................32

Change Input Port...................................................................................................................................................32

Set Configuration....................................................................................................................................................33

Battery Replacement .................................................................................................................................................34

Specifications.............................................................................................................................................................34

IRT Troubleshooting ..................................................................................................................................................34

RS232 Upgrade OF the Front Panel LCD Firmware.................................................................................................35

RS232 Connection Cables..........................................................................................................................................37

Pinout of RS232 port on VEEMUX............................................................................................................................37

Specifications for Straight-Through Serial Cable for CPU Connection .....................................................................37

Pinout for Matrix Y-1 Cable........................................................................................................................................38

Rack Mounting Instructions.......................................................................................................................................38

Specifications..............................................................................................................................................................39

Troubleshooting..........................................................................................................................................................39

Safety Statements .......................................................................................................................................................40

Index.............................................................................................................................................................................40

Warranty Information..................................................................................................................................................40

TABLE OF FIGURES

Figure 1- Install Video Source Cables................................................................................................................................................4

Figure 2- Connect a monitor to the VEEMUX....................................................................................................................................4

Figure 3- Connect user terminal for RS232 control............................................................................................................................5

Figure 4- Connect the LAN to the VEEMUX......................................................................................................................................5

Figure 5- LED Matrix showing input 5 connected to output 5.............................................................................................................6

Figure 6- RS232 connection with Matrix-Y-1 cable............................................................................................................................9

Figure 7- Web interface Welcome page..........................................................................................................................................18

Figure 8- Web interface Login Prompt.............................................................................................................................................18

Figure 9- Administrator Menu ..........................................................................................................................................................19

Figure 10- Web interface Switch page.............................................................................................................................................19

Figure 11- Web interface Setup page..............................................................................................................................................21

Figure 12- Web interface Serial Setup page....................................................................................................................................21

Figure 13- Administration menu.......................................................................................................................................................22

Figure 14- Add User page................................................................................................................................................................22

Figure 15- Edit User settings ...........................................................................................................................................................23

Figure 16- Web interface Video Input Names page.........................................................................................................................23

Figure 17- Output Port Names.........................................................................................................................................................24

Figure 18- Outputs Scanning Sequences page...............................................................................................................................24

Figure 19- Web interface Update Firmware page............................................................................................................................26

Figure 20- Web interface Password page........................................................................................................................................27

Figure 21- Updating the Web Server...............................................................................................................................................27

Figure 22- Web interface Logout page.............................................................................................................................................28

Figure 23- Device Discovery Tool....................................................................................................................................................29

iii

NTI VEEMUX VIDEO MATRIX SWITCH

INTRODUCTION

The SM-nXm-15V-LCD (n = number of inputs (video sources), m = number of outputs (monitors)) video matrix switch (VEEMUX)

allows any of up to 32 video sources to output to any or all of up to sixteen (16) monitors. The configuration of the VEEMUX is

determined at time of order (i.e. 16x4,32x8, etc.). The bandwidth of the SM-nXm-15V-LCD is 200MHz and video resolutions

through 1900 x1200 are supported with no degradation. The switch can be controlled with the Front Panel Keypad, RS232

interface, Ethernet, or an optional Infrared Remote.

The VEEMUX can be ordered in many sizes and with several control options. The base unit includes a user keypad, an RS232

port, and an Ethernet port to make up a complete system. The infrared option, purchased separately, allows for maximum user

satisfaction in each unique configuration.

Basic Operation

The VEEMUX allows any source to be connected to any destination at any time with no restrictions or limitations.

•Video inputs accept any RGBHV, RGBS, or RGsB signal.

•Video outputs are compatible with any RGBHV or RGBS monitor, regardless of input. (RGsB monitor requires

RGsB input)

Supported Web Browsers

Most modern web browsers should be supported. The following browsers have been tested:

•Microsoft Internet Explorer 6.0 or higher

•Netscape 7.0 or higher

•Mozilla FireFox 0.9.2 or higher

Set your browser to always check if there is a newer version of the page than the version stored in cache. This action will ensure

that it will display the most up-to-date information.

Compatibilty

The SM-nXm-15V-LCD is made to support video inputs from VGA (15HD – H & V Sync) only.

Ordering Information

The SM-nXm-15V-LCD is built to a specific size ranging from 2, 4, 8, 12, or 16 monitors and 16 or 32 video sources. The “n” in the

part number represents the number of video sources. Select a switch built for 16, or 32 video sources. The “m” in the part number

represents the number of outputs (monitors). A switch built for 2, 4, 8, 12, or 16 monitors may be ordered. It is not necessary to

fully populate all of the connectors on the unit (ex. an SM-16x8 switch has the capability of supporting 16 video sources and 8

monitors, but it is capable of operating with only 14 video sources with 7 monitors connected.

SM-nXm-15V-LCD

Replace the “n” with 16, or 32

Replace the “m” with either 2, 4 ,8,12,or 16

The following list represents the available sizes that can be ordered:

SM-16x2-15V-LCD

SM-32x2-15V-LCD

SM-16x4-15V-LCD

SM-32x4-15V-LCD

SM-16x8-15V-LCD

SM-32x8-15V-LCD

SM-16x12-15V-LCD

SM-32x16-15V-LCD

SM-16x16-15V-LCD

Options

Infrared Control (see page 30)

This feature adds the ability to control the VEEMUX via an infrared remote.

This feature is ordered by adding the suffix "-IR" to the model number when ordering (i.e. SM-4X2-15V-LCD-IR)

NTI VEEMUX VIDEO MATRIX SWITCH

Materials

Materials Supplied with this kit:

•NTI SM-nXm-15V-LCD Video Matrix switch

•IEC Line cord, country specific

•4-#10-32 x 3/4" pan head screws and 10-32 cagenuts (server cabinet mounting hardware)

Cables

All cables are sold separately. The following tables list the available stocked cables with their length in feet. All VGA input and

output connectors on Matrix Switches are FEMALE. When using multi-coax high resolution VGA to BNC cables, the BNC

connectors are also FEMALE for input and output. Custom cables are available – contact NTI for pricing and distance / resolution

limitations.

NTI NAME

DESCRIPTION

VGA

VEXT-3/6/10/15/25/35/50/75/100-MM

VEXT-3/6/10/15/25/35/50/75/100

VINT-5B-6

Multi-coax high resolution VGA or SVGA video cable. Connectors are 15HD male-male

(used for INPUTS)- 3 thru 100 feet

Multi-coax high resolution VGA or SVGA video cable. Connectors are 15HD male-

female (used for OUTPUTS)-3 thru 100 feet

Multi-coax high resolution VGA to BNC cable. Connectors are 15HD male to 5 BNC’s-6

feet long

RS232

Matrix-Y-1 or see page 37 for

alternative cables

RS232 Interface Cable- Connectors are 9D male- female-female 12" long

(also see alternative cable specifications on page 37)

ETHERNET

Contact NTI for various lengths and

colors

Cat5 UTP Cable- Connectors are RJ45 male-Stocked cables are 2 thru 100 feet

Custom cables must have RJ45 connectors wired straight thru- pin 1 to pin 1, etc.

Default User Name and Passwords

The default Telnet password is admin (lower case letters only) . For instruction on using Telnet, see page

13.

(No username is required in order to use Telnet. You will only be prompted for a password.)

The default Web Interface user name is Administrator (upper case letter for "A" only).

The default Web Interface password is admin (lower case letters only). For instruction on using the Web

Interface, see page 18.

NTI VEEMUX VIDEO MATRIX SWITCH

FEATURES AND FUNCTIONS

1. LCD Display- for visual indication of connection between the monitor and a specific video source.

2. Keypad buttons- for user control over switch functions

3. Fuse holder- holder for replaceable overcurrent 2A 240VAC Fast-blo protection fuse

4. IEC Power Connector- for attachment of power cord

5. Power ON/OFF switch

6. Ethernet-RJ45 female connector-for connection of CAT5 cable to LAN for WEB interface

7. RS232- female 9D connector-for attaching RS232 interface cable from a CPU to control the functions of one or more

switches

8. VIDEO x - female 15HD connectors- for connection of video source cables

9. MONITOR x-female 15HD connectors-for connection of monitors

10. LED Matrix- for visual indication of all input-to-output connections (page 6)

NTI VEEMUX VIDEO MATRIX SWITCH

INSTALLATION

Connect the Sources and Monitors

1. Power OFF all video sources (inputs) that will be connected to the VEEMUX before connecting or disconnecting any cables.

2. Connect a VEXT-xx-MM cable from the video port of a video source to a 15HD female video connector labeled “VIDEO 1” on

the VEEMUX. (See Figure 1)

3. Connect additional video sources to remaining 15HD female “VIDEO x” connectors as desired.

Figure 1- Install Video Source Cables

4. Connect a monitor to the 15HD female connector labeled “MONITOR 1” on the rear of the VEEMUX (See Figure 2).

5. Connect additional monitors to remaining 15HD female “MONITOR x” connectors as desired.

Figure 2- Connect a monitor to the VEEMUX

NTI VEEMUX VIDEO MATRIX SWITCH

Connect RS232

RS232 control can be achieved using a separate user terminal or CPU with a terminal program. To make a terminal connection,

connect a serial cable (specifications on page 37) between the user terminal and the 9 pin DIN female connector on the VEEMUX

labeled "RS232". (See Figure 3)

Figure 3- Connect user terminal for RS232 control

Connect to the Ethernet

If the Telnet Interface (page 13) or Web Interface (page 14) will be used, an Ethernet connection to the Local Area Network (LAN)

must be made using CAT5 cable with RJ45 connectors. Wiring between the connectors should be straight through (pin 1 to pin

1, pin 2 to pin 2, etc.) Connect a CAT5 cable between the connector labeled "ETHERNET" and the LAN (see Figure 4).

Figure 4- Connect the LAN to the VEEMUX

NTI VEEMUX VIDEO MATRIX SWITCH

Power Up

1. Plug the VEEMUX into an AC power outlet.

2. Power ON the VEEMUX.

3. Power ON the video sources and monitors connected to the VEEMUX.

LED MATRIX

The LED Matrix is a grid of LEDs on the front panel of the VEEMUX. This grid is used to provide a visual indication of all

connections between video sources and destinations. To determine if an input (video source) is connected to an output (video

destination), follow the LEDs down and to the right (respectively) until they intersect. The illuminated LED at the point of

intersection indicates the input is connected to the output by the VEEMUX.

Figure 5- LED Matrix showing input 5 connected to output 5

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Network Technologies Incorporated Matrix-Umschalter Handbücher

Network Technologies Incorporated

Network Technologies Incorporated SM-X-15V-LC Series Bedienungsanleitung

Beliebte Matrix-Umschalter Handbücher anderer Marken

Broadcast Tools

Broadcast Tools SS 8.2 Bedienungsanleitung

Altimium

Altimium MATF32 Bedienungsanleitung

ALFAtron

ALFAtron ALF-MUK44N Bedienungsanleitung

Monoprice

Monoprice Blackbird 15377 Bedienungsanleitung

Kramer

Kramer XL 3216VS Bedienungsanleitung

PTN

PTN FMX12 Bedienungsanleitung

CYP

CYP nT15GX01 Bedienungsanleitung

Kramer

Kramer VP-2x2 Bedienungsanleitung

Kramer

Kramer Sierra Video 6432V5xl Bedienungsanleitung

TESmart

TESmart HMA0402A40 Bedienungsanleitung

Octava

Octava HD4XSTPMX Bedienungsanleitung

Intelix

Intelix FLX-88 Betriebsanleitung

Kramer

Kramer LASSEN XL 3232S Bedienungsanleitung

Roland

Roland XS-1HD Bedienungsanleitung

Kramer

Kramer VS-66HDCPxl Bedienungsanleitung

Atlona

Atlona AT-HDMI-22M Bedienungsanleitung

Link

Link HD8X8 Bedienungsanleitung

AMX

AMX AVS-OP-2020-117 Anleitungen und Rezepte