Nex Dryft A90 BLDC Bedienungsanleitung

Have more questions? Talk to us at care@nexlife.com

FEEL THE FUTURE

This handy guide will help you

put your Nex fan together.

INSTRUCTION

MANUAL

Classification | Internal

CONNECTION

WIRES

BOTTOM CANOPY

Figure 1 Figure 2

MOTOR

BLADE

THERMO BUFFER BLADE FIXING SCREW

Figure 5Figure 4Figure 3

CONNECTION

WIRES

CANOPY STOPPER

DOWN ROD

MOTOR

CONNECTION

WIRES

CANOPY STOPPER

DOWN ROD

ASSEMBLY & INSTALLATION: FAN

INSTALLATION & ASSEMBLY OF BLADE

Note :- Kindly use same serial number blade as these are precisely balanced for same weight.

1. Place the motor on thermo buffer to avoid any scratches as shown in (Figure 1).

2. Unscrew the blade screw from Motor and align the blade with the motor as shown in

(Figure 1).

3. Screw the Blade to the Motor and ensure a tight fit.

CONNECTION

WIRES

CANOPY

STOPPER

Figure 6A

Figure 6B

Classification | Internal

INSTALLATION OF HANGING

ASSEMBLY & CANOPIES TO MOTOR

1. Hold the down-rod vertically with Slit side downward.

2. Slide canopy stopper (4a) from top end of down rod & Ensure

stopper should be below down rod(3)slit hole. Now Pass the

connection wires through slit hole at the Bottom end of down

rod (3) and remove them from the top end of down rod (Figure

2).

3. Insert the bottom end of down rod (3) (with slit) on spindle (6)

and insert bolt (7) Place the plain washer (8), spring washer (9),

and fully tighten nut (10), insert the split pin (11) in the small

hole on the bolt end and open the ends, so that it does not fall

off. The assembly of bolt (7), plain washer (8), spring washer

(9), nut (10), split pin (11) is separately packed with hanger

assembly (18).

4. Align hole in downrod (3) and slot in canopy stopper (4a) and

push canopy stopper (4a) from top to rest it on bolt (3).Now

pass connection wire through canopy stopper slot & connect to

the terminal block. (Figure 6a).

5. Slide the bottom canopy (4) from top end of down rod (3) and

rest it on canopy stopper (4a) (Figure 4).

6. Slide the top Canopy(5) in Bottom canopy (4) and push it

downward. (Figure 5)

7. Slide the false ceiling cover (5b) from top end of down rod (3)

and rest it on top canopy (5) (Figure 5).

8. Remove the split pin (17), nut (16), spring washer (15), plain

washer (14), bolt (13), at the bottom end of hanger assembly

(12).(Figure 6)

9. Place hanger assembly (12) in ceiling hook in such a way that

rubber reel (18) rests on the ceiling hook.

10.Insert the top end of down rod (3) between the steel clamps of

hanger assembly (12). Match the holes with holes in down rod

(3). Insert bolt (13), place plain washer (14), spring washer (15),

and fully tighten nut (16), insert the split pin (17) in the small

hole on bolt end and open the ends, so that it does not fall off.

11. Assemble top canopy (5) and false ceiling cover (5b) together

and lift the Top canopy (5) and false ceiling cover (5b) to cover

hanger assembly and fix with screw (5a) (Figure 6).

12. Regulator not recommended with BLDC remote Fan

CONNECTION

WIRES

TERMINAL

BLOCK

TOP END OF

DOWN ROD

BOTTOM END OF

DOWN ROD

WITH SLIT

MOTOR

BODY

Canopy stopper

CANOPY CUT

Figure 7

Figure 8

Classification | Internal

IN CASE OF FALSE CEILING WHERE DOWN

ROD IS ALREADY INSTALLED IN CEILING

1. Assemble top canopy (5) and false ceiling cover (5b) together (figure 7) and slide it up from

bottom end of down rod (already mounted).

2. Slide the bottom canopy(4) from down side of top canopy(5).

3. Slide canopy stopper (4a) from bottom end of down rod (already mounted) (Figure 7).

4. Insert the bottom end of down rod (already mounted) (with slit) on spindle (6) and insert bolt (7)

Place the plain washer (8), spring washer (9), and fully tighten nut (10), insert the split pin (11)

in the small hole on the bolt end and open the ends, so that it does not fall off. The assembly of

bolt (7), plain washer (8), spring washer (9), nut(10) split pin (11) is separately packed with

hanger assembly (12). & connect connection wire with terminal block.

5. Push canopy stopper (4a) from top to rest it on bolt (7) (Figure 7). Slide down bottom canopy and

rest it on canopy stopper.

6. Lift the Top Canopy (5) and false ceiling cover (5b) assembly as per requirement to cover false

ceiling hole and Tighten the screw (5a) to fix it (Figure 6).

NOTE

If there, is not sufficient space to accommodate top canopy (5), kindly cut top canopy (5) from bottom

side below screw hole and assemble false ceiling cover (5b) in top canopy (4) and assemble as per

instruction (Figure 8).

TERMINAL

BLOCK

BOTTOM END OF

DOWN ROD

MOTOR

BODY

Down Rod (already mounted)

Top canopy

False Ceiling cover

Bottom Canopy

Canopy Stopper

CONNECTION

WIRES

TERMINAL

BLOCK

TOP END OF

DOWN ROD

BOTTOM END OF

DOWN ROD

WITH SLIT

MOTOR

BODY

Canopy stopper

CANOPY CUT

Classification | Internal

1. To optimize the air delivery and avoid turbulence ceiling fan should be approx. 7 ~ 8 feet from the

ground level and 1 feet below the ceiling/false ceiling (if Applicable).

2. Minimum distance between blade tip and wall & between 2 Fans blade tip should be almost equal

or more than the fan sweep size.

3. Don’t mix the blade of one set with another set as these blades are balanced and packed as a set for

efficient performance and safety.

4. In case of false ceiling, the hole in false ceiling must be in line with ceiling hook and minimum 1

inch gap should be available all around the down rod.

5. Ensure that the down rod &fan blade are placed away from any ceiling beam for proper assembly,

follow the down rod instruction given in the diagram

IMPORTANT

The diagram of fan are just the general representation of ceiling fan and not the actual fan. Read the

instructions carefully. Open the packing and arrange the fan parts as per the numers marked on

diagram. Assemble & install fan as per the assembly, wiring diagram and written instruction. Check the

assembled fan, ensure proper installation before switching ON the fan.

PRECAUTIONS

REMOTE CONTROL

DIAGRAM

Power ON/OFF

To increase or decrease speed

in small steps while running.

Speed 1 to 5

2 Hrs. timer

6 Hrs. timer

To stimulate natural breeze

by varying the speed

periodically.

BREEZE

1 3

FINE SPEEDTIMER

REMOTE PAIRING

INSTRUCTIONS

IF PAIRING FAILS REPEAT ABOVE STEPS

PERFORM WITHIN 10 SECONDS

STEP 1 Initially Switch OFF the fan from mains supply

STEP 2 Switch ON the fan from mains supply.

STEP 3 Press the "POWER" button on the remote. Then Press "Speed 1" button on the remote within 10secs.

Successful pairing will be confirmed by two beeps from the Controller

PAIRING ACKN-

OWLEDGEMENT

Classification | Internal

TURN "OFF" FAN

FROM MAINS

2 BEEPS

INDICATES

SUCCESSFUL

PAIRING

HOLD THE

REMOTE IN

HAND

1.TURN "ON" FAN FROM MAINS SUPPLY

2.PRESS "POWER" BUTTON ON REMOTE

3.THEN PRESS "SPEED 1" ON REMOTE

WITHIN 10 SECONDS

Note: If pairing fails, repeat the steps after switching OFF and powering ON the fan from the mains supply

Note: Multiple fans can be paired with single remote

REMOTE UN-PAIRING INSTRUCTIONS (FAN OPERATES WITH TWO REMOTES)

INSTRUCTION 1: PCB Controller have 2 memories for remote.

INSTRUCTION 2: Remote 1 & Remote 2 both can be paired with the ceiling fan

INSTRUCTION 3: Firstly Remote 1 gets paired with PCB. Then Remote 2 gets paired. Pairing should happen within 10 secs.

Both memories of the controller are filled with Remote 1 & Remote 2. Now the fan will operate as per Remote

1 & Remote 2 command.

INSTRUCTION 4: You can remove Remote 1 from pairing list and pair the PCB with Remote 3

INSTRUCTION 5: Once you remove Remote 1 from pairing list, memory of the controller is filled with Remote 2 & Remote 3.

Now you can operate the fan with Remote 2 & Remote 3. After that, PCB won't respond to the commands of Remote 1.

SINGLE REMOTE PAIRING INSTRUCTIONS (FAN OPERATES ONLY WITH SINGLE REMOTE)

INSTRUCTION 1: If you want to operate with single remote means you want to pair the PCB with single remote you can pair, it

for 2 times within 10 seconds.

That means both the memories are filled with single remote. Now you can operate the fan with single remote

only (Remote 1).

TROUBLE-SHOOTING

INSTRUCTION

Problem Causes Solutions

Excessive gap between

Bottom canopy and Top Cover

A. Opposite Placement of Canopy

Stopper

A. Ensure the slotted bush of canopy

stopper must be on upper side

Power is ON but fan is

not working

Noisy operation

A. Circuit breaker tripped A. Reset the breaker

B. Loose connection of wire B. Tighten the wire connections

C. Fan turned OFF with the remote C. Press the power button to turn

ON the fan

D. Remote not paired with the fan D. Follow the remote pairing

instructions to pair the remote

A. Place the canopy stopper

in down rod

A. Bottom canopy touching the

top cover of Fan

B. Tight the mounting screw of the bladeB. Fan blade does not tighten properly

C. Input wire coming out from the

down rod and touching the top cover

C. Reduce the length of the wire

to avoid touching the top cover

Excessive Shaking Down rod not fitted tightly Tighten the bolt and nut as per

Instruction Manual

Fan speed increasing

& Decreasing

Fan is operating in breeze Mode Press the breeze/all 5 speed/fine

speed button to exit the breeze mode

Fan speed not changing when

using speed buttons of remote

Frequent commands received

by remote

Give 1-2 sec delay between

remote commands

B. Remote batteries drained B. Replace the old remote batteries

with the new batteries

Initial Jerk & Starting Problem Shackle kit is loose Tighten the shackle kit properly

Remote does not work A. Remote not paired with the fan A. Follow the remote pairing

instructions to pair the remote

Fan restart Fault detected Fan will restart once fault condition

no longer exists

Fan not working Fan turned off after timer completed

pre-set time

Restart the fan by using any of 1-5

speed button or power button

B. Bottom Canopy does not rest on

Canopy stopper

B. Pull Bottom Canopy downward

up to canopy stopper

All 2 canopies not fitting

in false ceiling

Down rod length is short because

of false ceiling

Remove the top canopy of the Fan

and fix the Ceiling cap above Bottom

Canopy at wider diameter groove side.

Classification | Internal

WARNING

THE INSTALLATION OF THE FANS SHOULD BE AS PER INSTRUCTION MANUAL TO AVOID ANY

DAMAGE TO FANS AND OTHER MOVING PARTS. DAMAGE OF ANY MOVING PARTS DUE TO

IMPROPER INSTALLATION MAY LEAD TO INJURY.

Room Size Fan Sweep

Less than 8 X 8 ft 600mm (24 ”)

8-10 ft X 8-10 ft 900mm (36 ”)

11-13 ft X 11-13 ft 1200mm (48 ”)

14-16 ft X 14 -16 ft 1300mm (52 ”) 1400mm (56 ”)

SELECTION GUIDE

Ceiling Fan

recommend Sweep

for different room sizes.

WIRING DIAGRAM

Figure 9

DOWN ROD DIAGRAM

Figure 10

RED

SUPPLY

FAN MOTOR BODY

N N

BLACK

Classification | Internal

ALL DIMENSIONS ARE IN mm

OD of Downrod

must be Ø 18.5 mm

minimum

Ø 18.5

Ø 8

Down Rod

SLIT MUST

BE STRAIT

2.5 MINIMUM

1.6

Ø 7.5

Thickness of Down rod

must be 1.6 mm minimum

This Dimension Must be

8mm From Down Rod end to

ø7.5mm Hole End

INSTALLATION OF SUPPORT

CABLE WITH FAN

Fig- 1

CAUTION

Installation of Secondary Support Cable

The purpose of Secondary support Cable is to temporarily hold the fan with ceiling hook, in case

of failuse of primary suspension system, which may happen due to faulty installation, inadequate

tightening of fasteners like nut & bolts etc. The fan should be switched off immediately & faulty

system should be corrected before using again.

Fig- 3

Un wind the support cable (2) and remove the

metal clamp (3).

Pass the cable through the shaft hole/ support

clip 1 (Hole below Down rod assembly hole)

so that it stops at the beaded end.

Thread the Cable (2) thro' the two holes on

cable clamp (3) & then thro" the ceiling hook

(4). Loop it & thread the free and thro another

set of hole in the clamp. Ensure that the Cable

is slack & approximately about an inch losse

and in no case supporting the fan directly as

shown in Fig - 3 & Fig - 4. Then fully tighten

the clamp by tightening nut & screw to ensure

that the secondary support is rigidly held.

Fig- 2 Fig- 4

Push the free end of cable (2) thro' the hole in

the down rod (thro' which supply

wires are not run) till it comes out of the

shackle end.

Fold the free and of the Cable (2). Raise the

canopy to appropriate position. Likewise place

the condensor cover in it's desire position.

Inhaltsverzeichnis

Andere Nex Lüfter Handbücher

Nex

Nex Glyde A50 Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Hinkley

Hinkley HIGHLAND Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung