Nexcom EBC 300 Series Bedienungsanleitung

www.nexcom.com

Single Board Computer

EBC 300 Series

User’s Manual

07-13-2006 Build

Nov-15-2006 Edit

EBC 300 User’s Manual 1 Preface

Preface

This publication, including all photographs, illustrations and software, is protected under international

transmitted in any form or by any means without the prior written consent from NEXCOM International

Co., Ltd.

Version 1.2

Disclaimer

The information in this document is subject to change without prior notice and does not represent

commitment from NEXCOM International Co., LTD. However, users may update their knowledge of any

product in use by constantly checking its manual posted on our website: http://www.nexcom.com.

NEXCOM shall not be liable for direct, indirect, special, incidental, or consequential damages arising out

of the use of any product, nor for any infringements upon the rights of third parties, which may result from

such use. Any implied warranties of merchantability of fitness for any particular purpose is also

disclaimed.

Acknowledgements

The EBC 300 series is a trademark of NEXCOM international CO., LTD. All other product names

mentioned herein are registered trademarks of their respective owners.

Regulatory Compliance Statements

This section provides the FCC compliance statement for Class A devices and describes how to keep the

system CE compliant.

Federal Communications Commission (FCC) For Class A Device

This equipment has been tested and verified to comply with the limits for a Class A digital device, pursuant

to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. Operation of this equipment in a residential area

(domestic environment) is likely to cause harmful interference, in which case the user will be required to

correct the interference (take adequate measures) at their own expense.

EBC 300 User’s Manual 2 Preface

CE Certification

The product(s) described in this manual complies with all applicable European Union (CE) directives if it

has a CE marking. For computer systems to remain CE compliant, only CE-compliant parts may be used.

Maintaining CE compliance also requires proper cable and cabling techniques.

WARNINGS

Read and adhere to all warnings, cautions, and notices in this guide and

the documentation supplied with the chassis, power supply, and accessory

modules. If the instructions for the chassis and power supply are inconsistent

with these instructions or the instructions for accessory modules, contact

the supplier to find out how you can ensure that your computer meets

safety and regulatory requirements.

CAUTION

Electrostatic discharge (ESD) can damage NSA components. Do the

described procedures only at an ESD workstation. If no such station is

available, you can provide some ESD protection by wearing an antistatic

wrist strap and attaching it to a metal part of the computer chassis.

Safety Information

Before installing and using the EBC 300, note the following precautions:

Read all instructions carefully.

Do not place the unit on an unstable surface, cart, or stand.

Follow all warnings and cautions in this manual.

When replacing parts, ensure that your service technician uses parts specified by the manufacturer.

Avoid using the system near water, in direct sunlight, or near a hearing device.

EBC 300 User’s Manual 3 Preface

EBC 300 User’s Manual 4 Table of Content

Table of Content

Preface……………...……………..……………………………………….………….……..……………..2

Disclaimer………………………..………………………………..…………………………………….. 2

Acknowledgements……………………………………………..……………………………..…..…… 2

Regulatory Compliance Statements……………………..…………………………………….……………2

Federal Communications Commission (FCC) For Class A Device……………..……….…………..…..…1

CE Certification………………………………………………………………………….……….………...3

Safety Information……………………………………………………………………….………..………..3

Table of Content………………………………………………………………………………….…………4

Chapter 1 General Information

1.1 Main Feature…………………………………………………….…………………………….……….. 7

1.2 Specifications……………………………………………………..…………………………………….7

1.3 Power Consumption Measurement…………………..…………………………………………………10

1.4 Board Layout…………………………………………………………………….………………….….10

Chapter 2Jumper Setting

2.1 Before You Begin……………………………………………..….……………………………………12

2.2 Precautions………………………………………………………………………………………...…..12

2.3 Setting Jumpers………………………………………………………………………………………..13

2.4 Location of Jumpers……………………………………………………………………………….…..14

2.5 Function of Jumper…………………….…….……………………………………………………..…..16

Chapter 3 Expansion

3.1 System Memory………………………………………………………………………………….…….25

3.2 Installing Compact Flash………………………..……………………………………………………..26

EBC 300 User’s Manual 5 Chapter 1

Chapter 1

General Information

EBC 300 User’s Manual 6 Chapter 1

1.1 Main Feature

Support Intel Celeron M 600MHz processor with 512K L2 cache and 400MHz FSB

Support Intel® Pentium® M processor or Intel® Celeron® M processor in 478-pin, Micro-FCPGA

package (mPGA479M Socket)

• Intel® 82852GM and Intel® ICH-4 chipsets

• Onboard 256 MB Non-ECC DDR 200/266/333/400 SDRAM

• Realtek® RTL8110SC Gigabit Ethernet Controller x 1 supporting one GbE LAN port

• DB-15 VGA Connector

• Support IDE HDD

• CompactFlash Socket

• USB 2.0 Port x 6, COM x 1

1.2 Specifications

Figure 1.1: Block Diagram of EBC 300

EBC 300 User’s Manual 7 Chapter 1

System Architecture -3.5” Embedded SBC

CPU Support

- Standard: Support Intel Celeron M 600MHz processor with 512K L2 cache

and 400MHz FSB

- Optional: Support Intel® Pentium® M processor or Intel® Celeron® M

processor in 478-pin, Micro-FCPGApackage (mPGA479M Socket)

Memory

- Onboard 256 MB Non-ECC DDR SDRAM

- 200/2666/333/400

BIOS

- Award system BIOS

- ACPI: Only support Software Shutdown by 5Vsb Provided (S0 /S5 only)

- Advanced Power Management support

- 4M bits flash ROM

Support Pentium M Speed Step (Customized by Nexcom)

Chipset

- Intel® 82852GM

- ICH-4

LAN - Realtek® RTL8110SC Gigabit Ethernet Controller x 1 supporting one GbE

LAN port

Display

- Intel® 852GM integrated graphics solution w/ Intel® Extreme Graphics 2

technology

- Up to 64 MB of dynamic video memory allocation

- 350-MHz integrated 24-bit RAMDAC that can drive a standard progressive

scan analog monitor with pixel resolution up to 1600x1200 at 85 Hz,

2048x536@75Hz

- DB15 CRT VGAConnector x 1

- CRT: Wide Screen Resolution support 848x480 and 1366x768 only

- LVDS: LFP (local flat panel) LVDS interface/Single- or dual-pixel LVDS

panel support up to UXGApanel resolution (1600x1200)/DF13-20DP, 20-pin

connector x 1 for LVDS panel output

- Wide Screen Resolution support 848x480 and 1366x768 only

IDE - HDD: Support IDE with 44 pin connector ×1 (Primary)

EBC 300 User’s Manual 8 Chapter 1

- Internal CompactFlash socketx1

Support One Type II CompactFlash Card (Secondary)

- On Board Power LED and HDD Active LED Pin Header

Audio - REALTEK ALC655-LF AC97 CODEC

- Microphone in, Speaker out (external)

I/O Interface

- SIO×1, with 1x16C550 UARTs, One DB9 Connector

- USB2.0 connector x 6 (two direct output, 4 from Jst Box Header)

- HDD: Support IDE with 44 pin connector ×1 (Secondary)

- Internal CompactFlash socket x 1

Support One Type II CompactFlash Card (Primary)

- On Board 2 pin header for Reset switch

- 8 GPIO lines via header (GPI 0~3 and GPO0~3)

- TTL Level (0/5V)

- On Board HDD Active LED Pin Header

- Reserved 3 PIN FAN Connectors x 1 (for CPU)

- On board 3 pin header for I2C, one pin for GND

- PC/104 Plus Connector x 1

Expansion Slot - PC/104 Plus Connector x 4 (PCI Only)

I/O on Bracket

- VGA

- RJ-45

- Mic-In

- Speaker Out

- COM

- USB x 2

System Management

- Derived from Super IO to support system Voltage, fan speed, temperature

monitoring

- Watchdog Timer: Watchdog timeout can be programmable by Software

from 1 second to 64 Sec. (Tolerance 10% under room temperature 25°C)

Real Time Clock

- On chip RTC with battery back up

- External Li-ion Battery x 1 (Socket type field replaceable)

- The Battery Socket should be Flat direction.

Tolerance less 2 sec ( 24 hours ) under 25 °C environment

Dimensions - 146mm(L) x 105mm(W)

Power Supply

- AT Mode: +5V Power in, No Power On push Button, Software Shutdown

function and LAN remote wake up; BIOS and H/W is default to AT Mode

- ATX Mode: +5V / +12V /-12V / -5V / 5Vsb Power In

When Change to ATX Mode, the BIOS default setting is as follow:

POWER -SUPPLY TYPE [ATX]

AUTO PWR-FAILURE RESUME [ON]

EBC 300 User’s Manual 9 Chapter 1

Environments

- Board-level operating temperatures: -20°C to 60°C

- Storage temperatures: -20°C to 80°C

- Relative humidity: 10% to 90% (Non-condensing)

Certification

- CE

- FCC ClassA

Ordering Information

EBC 300-C65-256M

3.5” Low Power Embedded Board with Celeron M 600MHZ 512KB L2 on Board with VGA/

LVDS/Audio/COM/ USB2.0 / Gigabit LAN

EBC 300-SKT-256

3.5” Low Power Embedded Board with Pentium M / Celeron M CPU Socket with VGA/

LVDS/Audio/COM/ USB2.0 / Gigabit LAN

1.3 Power Consumption Measurement

Power Requirement:

System Configuration OS: WinXP / Memory: 256MB / Storage: 40GBTest

Program : K Power + Burning Test

Voltage +5V

(A)

+12V

(A)

+5Vsb

(A)

-12V

(A)

Theoretical Current:

R&D Design Max. Power Loading 14.6A 1.176A 0.3A 0.235A

Heavy :

Maximum HD/CPU and Memory Loading 7A 0.05A (AT)

0.05A (ATX) 0.20 (ATX) For PC/104

Normal: ( without K power test )

25% HD / 70% CPU and 50% Memory Load

3.14A (AT)

3.13A (ATX)

0.05A (AT)

0.05A (ATX) 0.20A (ATX) N/A

Idle:

OS in idle state

2.96A (AT)

2.94A (ATX)

0.05A (AT)

0.05A (ATX) 0.19A (ATX) N/A

Note: -12V is reserved for PCI-104 expansion requirement, the table only show the R&D design max. power support

EBC 300 User’s Manual 10 Chapter 1

1.4 Board Layout

Figure 1.2: Overview of EBC 300

Inhaltsverzeichnis

Andere Nexcom Hauptplatine Handbücher

Nexcom

Nexcom PEAK650VL2B Bedienungsanleitung

Nexcom

Nexcom Neu-X300-H310 Bedienungsanleitung

Nexcom

Nexcom PEAK 637 Bedienungsanleitung

Nexcom

Nexcom NEX 614 Bedienungsanleitung

Nexcom

Nexcom NEX 609 Bedienungsanleitung

Nexcom

Nexcom NEX 614A Bedienungsanleitung

Nexcom

Nexcom NSA 3180A Bedienungsanleitung

Nexcom

Nexcom COM Express Type 6 ICES 673 Bedienungsanleitung

Nexcom

Nexcom NEX 605 Bedienungsanleitung

Nexcom

Nexcom Peak 550 Bedienungsanleitung

Nexcom

Nexcom NEX 883 Bedienungsanleitung

Nexcom

Nexcom NEX 812 Bedienungsanleitung

Nexcom

Nexcom NEX 650 Bedienungsanleitung

Nexcom

Nexcom EBC575 Series Bedienungsanleitung

Nexcom

Nexcom Peak 602VL Bedienungsanleitung

Nexcom

Nexcom ICES 675 Bedienungsanleitung

Nexcom

Nexcom NEX 912 Bedienungsanleitung

Nexcom

Nexcom NEX 910 Bedienungsanleitung

Nexcom

Nexcom PEAK 715-HT Bedienungsanleitung

Nexcom

Nexcom EBC 580 Bedienungsanleitung

Nexcom

Nexcom PEAK 779VL2 Bedienungsanleitung

Nexcom

Nexcom PEAK 886VL2 Bedienungsanleitung

Nexcom

Nexcom PEAK 886 Bedienungsanleitung

Nexcom

Nexcom Peak 555A Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung